Page 5
Product Guide Key Managed Bolt Mechanism CUE is a keypad lock designed to operate for shared or assigned use applications. In shared use functionality, the user chooses any available locker and enters a self-selected 4-digit code to lock and the same code to later unlock. Once unlocked, the locker is available for a different user.
Page 6
Product Guide Key Managed Bolt Mechanism Programming Instructions Register/Add Manager Key(s) Manager Key(s) can be registered to a lock after Initial Setup has been completed. Go to the lock requiring Manager Key(s). Press =` 55 `. The LED will turn on. Touch the Programming Key to the key slot until a two-tone beep is heard.
Page 7
Product Guide Key Managed Bolt Mechanism LED Usage Indicator (for shared use functionality only) When in shared use functionality, each lock can be programmed to have the LED flash or not flash while the lock is in use. The default setting is ON (red LED flashes while lock is in use).
Page 8
The front unit may not be properly connected to the rear unit. Remove the lock from the door and check the cable connection. ▪ If error condition persists, contact Digilock support. Battery Replacement It is not necessary to uninstall the lock from the door.
Page 9
Product Guide Key Managed Latch Mechanism CUE keypad locks with a deadlatch are designed to operate for assigned use applications. In assigned use functionality, the user is assigned a specific locker and a 4-digit code or User Key to operate the lock. A Programming Key unique to the lock system programs up to 25 Manager Keys to the locks for management access, external power, and inspection.
Page 10
Product Guide Key Managed Latch Mechanism Programming Instructions Register/Add Manager Key(s) Manager Key(s) can be registered to a lock after Initial Setup has been completed. Go to the lock requiring Manager Key(s). Press =`55`. The LED will turn on. Touch the Programming Key to the key slot until a two-tone beep is heard. Touch each Manager Key to the key slot.
Page 11
Product Guide Key Managed Latch Mechanism Operating Instructions Operate with an assigned User Code ▪ To unlock: Press = [assigned 4-digit code] `*. ▪ To relock: Close the door. Operate with an assigned User Key ▪ To unlock: Touch the assigned User Key to the key slot. ▪...
Page 12
The lock is binding which means that either door alignment or items in the locker are preventing the lock from operating. Press on the door while operating the lock. If error condition persists, contact Digilock support for assistance. 2 sets of three beeps: The batteries are low.
Page 13
Product Guide Code Managed Bolt Mechanism CUE is a keypad lock designed to operate for shared or assigned use applications. In shared use functionality, the user chooses any available locker and enters a self-selected 4-digit code to lock and the same code to later unlock. Once unlocked, the locker is available for a different user.
Page 14
Product Guide Code Managed Bolt Mechanism Programming Instructions Program a New 6-digit Owner Code The Owner Code can only be programmed by using the current Owner Code. Press =` [current Owner Code] `. A two-tone beep will be heard and the LED will turn on. Press = [new Owner Code] `.
Page 15
Product Guide Code Managed Bolt Mechanism Assign User Code (for assigned use functionality only) Make sure that the lock is set for assigned use functionality. Once a User Code is assigned, the previously assigned User Code will no longer operate the lock. Assign a User Code (default User Code = 1234): Press =` [Manager Code] `.
Page 16
The lock is binding which means that either door alignment or items in the locker are preventing the lock from operating. Press on the door while operating the lock. If error condition persists, contact Digilock support for assistance. 2 sets of three beeps: The batteries are low.
Page 17
Product Guide Code Managed Latch Mechanism CUE is a keypad lock designed to operate for assigned use applications. In assigned use functionality, the user is assigned a specific locker and a 4-digit code to operate the lock. Owner and Manager Codes provide management access and inspection. Lock Parts Front Unit Rear Unit...
Page 18
Product Guide Code Managed Latch Mechanism Programming Instructions Program a New 6-digit Owner Code The Owner Code can only be programmed by using the current Owner Code. Press =` [current Owner Code] `. A two-tone beep will be heard and the LED will turn on. Press = [new Owner Code] `.
Page 19
The lock is binding which means that either door alignment or items in the locker are preventing the lock from operating. Press on the door while operating the lock. If error condition persists, contact Digilock support for assistance. 2 sets of three beeps: The batteries are low.
Page 21
0.75 in (19 mm) Programming Key with external power Manager Key (up to 25) with external power 3.23 in (82 mm) User Key Strike plate 0.19 in (4.83 mm) 0.14 in Phone: 707 766 6000 | www.digilock.com | sales@digilock.com (3.57 mm)
Page 22
side view 0.75 in (19 mm) 3.70 in (94 mm) 1.53 in 2.83 in 0.75 in (39 mm) (72 mm) (19 mm) 0.45 in 3.70 in (11.5 mm) (94 mm) Door Thickness 0.75 in 0.19 in (19 mm) (4.83 mm) 1.53 in 2.83 in 2.32 in...
Page 23
0.75 in (19 mm) Programming Key with external power Manager Key (up to 25) with external power 3.23 in (82 mm) User Key Strike plate 0.19 in (4.83 mm) 0.14 in Phone: 707 766 6000 | www.digilock.com | sales@digilock.com (3.57 mm)
Page 24
side view 0.75 in (19 mm) 3.70 in (94 mm) 1.53 in 2.83 in 0.75 in (39 mm) (72 mm) (19 mm) 0.45 in 3.70 in (11.5 mm) (94 mm) Door Thickness 0.75 in 0.19 in (19 mm) (4.83 mm) 1.53 in 2.83 in 2.32 in...
Page 25
Brushed nickel or brass finish 2.32 in Accommodates multiple door thickness (59 mm) 0.75 in (19 mm) Power jumper Strike plate 3.23 in (82 mm) 0.19 in (4.83 mm) 0.14 in Phone: 707 766 6000 | www.digilock.com | sales@digilock.com (3.57 mm)
Page 26
(72 mm) (59 mm) 0.14 in (3.57 mm) 0.45 in (11.5 mm) Door Thickness 0.75 in 0.19 in (19 mm) (4.83 mm) 2.32 in (59 mm) 0.14 in (3.57 mm) top view Phone: 707 766 6000 | www.digilock.com | sales@digilock.com...
Page 27
Brushed nickel or brass finish 2.32 in Accommodates multiple door thickness (59 mm) 0.75 in (19 mm) Power jumper Strike plate 3.23 in (82 mm) 0.19 in (4.83 mm) 0.14 in Phone: 707 766 6000 | www.digilock.com | sales@digilock.com (3.57 mm)
Page 28
(72 mm) (59 mm) 0.14 in (3.57 mm) 0.45 in (11.5 mm) Door Thickness 0.75 in 0.19 in (19 mm) (4.83 mm) 2.32 in (59 mm) 0.14 in (3.57 mm) top view Phone: 707 766 6000 | www.digilock.com | sales@digilock.com...
Page 29
Installation Guide Cue front unit (code and key) Cue rear unit (latch & bolt)
Before Lock Installation � �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� Surface Mount Installation �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� For door thickness measuring between .01" - .91" (0.2 mm - 23 mm) ��������������������������������������������������������������������������������������������������� Required Components ������������������������������������������������������������������������������������������������������������������������������������������������������������������������� Installation ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� Door Preparation � ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ Strike Plate Installation �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� Required Components ������������������������������������������������������������������������������������������������������������������������������������������������������������������������� Installation �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� Door Mounting Holes Drill Instructions and Templates � ���������������������������������������������������������������������������������������������������������������������������������� Drill Instructions � ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� Template for Standard & Vertical Body � ������������������������������������������������������������������������������������������������������������������������������������������ Metal Door Preparation �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������...
Before Lock Installation The door must be prepared for lock installation. Strike Plate A strike plate must be installed. Angled Strike Plate Security Strike Plate Double Door Strike Plate Door Mounting Holes The door must have door mounting holes.
Surface Mount Installation For door thickness measuring between .01" - .91" (0.2 mm - 23 mm) Required Components 1 - Front Unit Key Managed Code Managed 1 - Rear Unit Deadbolt Deadlatch 2 - Phillips Head Screws 1* - Phillips Head Screwdriver (#2) 2 - Split Lock Washers *Not included...
Installation For illustration, a bolt rear unit is used. REAR VIEW FRONT VIEW Withtherearunitbehindthedoor,extendthecablethroughthedoor’smountinghole� REAR VIEW FRONT VIEW Attachthecabletothefrontunit�Atriplebeepindicatessuccessfulconnection� REAR VIEW FRONT VIEW Holdthefrontandrearunitsagainstthedoorandsecurewiththemountingscrews�...
Page 34
REAR VIEW FRONT VIEW Testthelockwhilethedoorisopen� For bolt units: Press = ` to extend the bolt. Press = ` again to retract the bolt For latch units: Press = ` to retract the latch Latch will extend automatically after approximately 6 seconds. Repeat test with the door closed.
Door Preparation Strike Plate Installation Required Components Strike Plate 1. A strike plate must be installed. Angled Strike Plate Security Strike Plate Double Door Strike Plate 1* - Phillips Head Screwdriver (#1) *Not included Do not use an electric screw gun unless it is equipped with a torque adjuster and is set to low.
Installation 0 . 3 2 ( 8 m Mark Here Position the strike plate on the door frame centering Allow .32" (8 mm) from door edge and mark the position of the adjustment slot holes. it with the center of the desired location of the door mounting holes.
Plate Center Template Center line Mark Door Edge Template Center line Door Mounting Holes Drill Instruction and Template Drill Instructions Edge of Strike Plate Door Edge Mark Template Strike Mark Strike Edge Marker Plate Drawn Template Marker Center Template Center line Mark Door Edge Mark Door Edge Align both the center line and strike plate edge of the...
Page 38
Template for Door Mounting Holes Templates may not print to scale. Check all measurements before proceeding. Before printing, turn off auto scaling in printer setup and print at 100%. All measurements in thousandths of an inch and millimeters ALIGN EDGE OF ALIGN EDGE OF STRIKE PLATE HERE STRIKE PLATE HERE...
Metal Door Preparation Compatibility Guide Digilock is compatible with a majority of 3-hole configuration, latch, and handle door types. Some doors may require modification to clear obstructions. Single Point Latch Standard Lift Handle Box Locker Padlock Hasp...
Removal of 3-hole Lock Plug Remove any obstructions to the door mounting holes. Rear View of Front View of Locker Door Locker Door with Lock Plug with Lock Plug...
Close the door and mark the area to nothing is protruding above the hasp on the marked cut-line. cut the padlock hasp. surface of the door. Smooth out rough or sharp edges. 707 766 6000 | sales@digilock.com | www.digilock.com IG-NXT-U-DEN 121715...
Need help?
Do you have a question about the NEXTLOCK CUE Series and is the answer not in the manual?
Questions and answers