Table of Contents
Advertisement
M.E.P. - operator's handbook - P35 corking machine
1. Read carefully this operator's handbook before operating our P35 corking machine.
2. M.E.P. guarantees his P35 corking machine in case of breakages caused by faulty
components or incorrect assembly.
3. Our P35 corking machine has a 12-month warranty. 12 month period begins on shipping date
from Brewcraft USA. This guarantee is valid only for the first owner of the corking
machine.
4. Warranty only consists in replacing the damaged parts and it does include neither refunds
for losses caused by the shutdown of the machine nor any cost of labor or any transport cost
to send the filling machine to a repair shop.
5. Any repair or modification made to the machine by unauthorized personnel will make the
warranty void.
6. We cannot be held responsible for damages due to incorrect use of the corking machine,
or failure to carry out maintenance and lubrication, or problems or damage incurred during
transport.
7. M.E.P. reserves the right to introduce changes without previous notice to the P35
corking machine; however, the supply of spare parts of the previous models will be
guaranteed.
CONDITIONS OF SALE AND WARRANTY
1
Advertisement
Table of Contents
Summary of Contents for MEP P35
- Page 1 2. M.E.P. guarantees his P35 corking machine in case of breakages caused by faulty components or incorrect assembly. 3. Our P35 corking machine has a 12-month warranty. 12 month period begins on shipping date from Brewcraft USA. This guarantee is valid only for the first owner of the corking machine.
-
Page 2: Table Of Contents
Our P35 corking machine meets the requirements of those wine-growers who need a rapid and precise corking. Our P35 corking machine is almost entirely made of stainless steel to make cleaning easier. Moreover all those parts which could come into contact with the corks are made of materials that... -
Page 3: Description Of The P35 Corking Machine
M.E.P. - operator's handbook - P35 corking machine SAFETY SYMBOLS: General Danger Caution: Refer to the Operators Handbook Caution: 230 Volt Tension Caution: Rotating Gears - Severing of Fingers... -
Page 4: Operating Directions
M.E.P. - operator's handbook - P35 corking machine OPERATING DIRECTIONS Our P35 corking machine is provided with an upper cork container which is fitted up with a mechanical mixing device that lines the corks up and pushes them through the descent duct for the corking to be carried out successfully. -
Page 5: Technical Details
M.E.P. - operator's handbook - P35 corking machine TECHNICAL DETAILS Standard equipment: cork size diameter 22-26 x 50 mm. bottle height up to 390 mm. corking time approximately 1,8 seconds Optional equipment: cork descent duct and cork pusher for corks with diameter up to 28 mm. -
Page 6: Instructions For Use
M.E.P. - operator's handbook - P35 corking machine INSTRUCTIONS FOR USE - Positioning. The P35 corking machine should be placed on an even ground. Make sure that the screws which hold the safety guards are screwed tight, especially those which hold the switch-board. - Page 7 M.E.P. - operator's handbook - P35 corking machine INSTRUCTIONS FOR USE CONTINUED Fill up the cork container and close the lid. When the lid is open, the respective sensor is not operated (see picture 3) and the corking machine cannot start.
-
Page 8: Vacuum / Azote
M.E.P. - operator's handbook - P35 corking machine CAUTION The corking machine can be used by only an operator at a time and no one else should be near when the feeding cable is connected and the corking machine is operating. - Page 9 M.E.P. - operator's handbook - P35 corking machine Azote Vacuometer connection Vacuum regulator Oil level of the pump Picture 5. CAUTION It is important to check the oil level of the air-pump before starting work. The oil level of the pump can be checked through a round indicator that can be seen through the fissures of the wheeled support (see picture 5: oil level of the pump);...
-
Page 10: Faults And Remedies Check List
M.E.P. - operator's handbook - P35 corking machine FAULTS AND REMEDIES CHECK LIST - When the machine is operating the green light (see picture 4) must be on. If it is not so, you must check that the pin of the plastic front guard starts the respective sensor in the correct way and the lid of the cork container is closed. - Page 11 (see picture 6). In case one does not succeed in carrying out the above mentioned adjustment (especially it could not be successful with synthetic stoppers) it is advisable to adjust the tightening of the jaws. Our P35 corking machine is set to compress the corks to a diameter of 16 mm.
- Page 12 If the vibrations continue it is advisable to loosen the bolts of the back guard (reference 108 on the table "Components of the P35 corking machine") and lubricate all the pins and bearings inside. In case the problem persists turn to the manufacturer.
-
Page 13: Maintenance
A long machine working life is dependent upon constant and methodical compliance with the following instructions: take off the back plate (reference 108 on the table "Components of the P35 corking machine") and lubricate the bearings, the slide and the pins inside the machine;... -
Page 14: Electric System Of The P35 Corking Machine
Electric system Fuse D� O loll � . , 1 16 A 10 WATT I I I I rl I I ii � 2 3 4 na na 10 11 12 20 21 } Pulsante push-button j ..� ..) Starting C : : Quick-stop push-button... - Page 15 Electric system for vacuum Fuse � lolll D: : D 16 A 10 WATT � 1111 11111111111 0 220 PUMP Commutator indicator o---n) Main o---1:tJ circuit board Vacuum indicator Sensor Electrovalve Electrovalve for gas for vacuum...
-
Page 16: Components Of The P35 Corking Machine
Components of the P35 Corking Machine... - Page 17 M.E.P. - operator's handbook - P35 corking machine POS. DESCRIPTION REF. POS. DESCRIPTION REF. 0,75 KW motor tap0201 Base tap1028 Reducer tap0202 Push-button sensor tap0225 Flange tap0203 M4x30 screw tap0309 Motor guard tap1317 Support tap0502 Right side plate tap1301 10 mm. diam. pin...
- Page 18 M.E.P. - operator's handbook - P35 corking machine POS. DESCRIPTION REF. POS. DESCRIPTION REF. Spring tap0008 103 Spring tap0004 Spacer tap1212 104 Cone tap0713 Left side plate tap1215 105 Block tap0719 Shaft tap1209 106 Lower safety guard tap1320 Cork container...
-
Page 19: Components Of The Wheeled Support
M.E.P. - operator's handbook - P35 corking machine COMPONENTS OF THE WHEELED SUPPORT POS. DESCRIPTION REF. POS. DESCRIPTION REF. Frame tap1330 Vacuum tank tap0233 Back plate tap1332-1 M12 nut tap0346 Front plate tap1332 Washer for M2 screw tap0345 M6x25 stainless screws...
Need help?
Do you have a question about the P35 and is the answer not in the manual?
Questions and answers