Table of Contents
Advertisement
Quik Bridge® Euro Repeater SAW Installation Instructions
Note
When DIP switch 8 is set to ON, the AC Failure and Jam Detection features are disabled.
2.
To use the repeater with the Euro Concord, you may set DIP switch 8 to either the OFF or
ON position.
Repeater No. 01
ON
1 2 3 4 5 6 7 8
Repeater No. 04
ON
1 2 3 4 5 6 7 8
Repeater No. 07
ON
1 2 3 4 5 6 7 8
Repeater No. 10
ON
1 2 3 4 5 6 7 8
Repeater No. 13
ON
1 2 3 4 5 6 7 8
Repeater No. 16
ON
1 2 3 4 5 6 7 8
Repeater No. 19
ON
1 2 3 4 5 6 7 8
Repeater No. 22
ON
1 2 3 4 5 6 7 8
Repeater No. 25
ON
1 2 3 4 5 6 7 8
Repeater No. 28
ON
1 2 3 4 5 6 7 8
Repeater No. 31
ON
1 2 3 4 5 6 7 8
Figure 5. DIP Switch Settings for Repeater Identification Numbers
Programming the Repeater into the panel
Before the panel can supervise the repeater, the repeater must be programmed into panel memory.
¾
To program the repeater into the panel:
1. Refer to the panel installation instructions for the sensor pro-
gramming procedure.
2. When the panel prompts you for a group number, we recom-
mend that you use group number 4. Group number 4 super-
vises the repeater and causes an instant alarm if the tamper is
tripped.
3. Trip one of the repeater tamper switches when the procedure
prompts you for sensor activation.
To trip the antenna tamper, remove one end of the antenna
from its terminal.
To trip the cover tamper switch, the switch must first be
closed. To close the switch, insert a wire jumper between the
terminals of the cover tamper switch as shown in Figure 6.
To trip the switch, remove the jumper.
Repeater No. 02
Repeater No. 03
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Repeater No. 05
Repeater No. 06
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Repeater No. 08
Repeater No. 09
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Repeater No. 11
Repeater No. 12
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Repeater No. 14
Repeater No. 15
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Repeater No. 17
Repeater No. 18
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Repeater No. 20
Repeater No. 21
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Repeater No. 23
Repeater No. 24
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Repeater No. 26
Repeater No. 27
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Repeater No. 29
Repeater No. 30
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Figure 6. Closing the Cover
Tamper Switch
5
Advertisement
Table of Contents
