Advertisement
Quick Links
Advertisement
Summary of Contents for Lyman Case Trim Xpress
- Page 1 Lyman ® Case Trim Xpress Instruction Manual SAVE THESE INSTRUCTIONS...
-
Page 2: Save All Warnings And Instructions For Future Reference
ORIGINAL INSTRUCTIONS Congratulations on your purchase of the Lyman Case Trim Xpress. Please read all instructions prior to use. Throughout the instruction manual you will find TRIMMING TIPS, these helpful tips will assist the user in set up, opera- tion and troubleshooting the trimmer. - Page 3 To reduce the risk of injury, user must read instruction manual Wear ear protection Wear eye protection Wear dust mask Warning Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.
- Page 4 f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool.
-
Page 5: Vibration Information
If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in order to avoid a safety hazard. Case Trim Xpress Specifications: 29V DC , 11W 0.38A AC ADAPTOR... -
Page 6: Unpacking And Setup
SECTION 1 UNPACKING AND SETUP Replacement Parts (Not Shown) A. Cap (Part #7810240) (#7810245) 29V DC Power Supply B. Bushing (See Chart on back) (#7994460) EU Cordset 230V C. Spring (Part #7810241) (#7994461) UK Cordset 230V D. Adjuster Barrel (Part #7810242) (#7994462) SA Cordset 230V E. - Page 7 SECTION 2 Setting Trim Length The Case Trim Xpress is supplied with 10 different bushings covering a wide range of popular bottleneck cases. Additional bushings can be purchased for calibers that are not covered by the supplied bushings. Please refer to the bushing chart on back for caliber information and part numbers.
- Page 8 different times there is a chance your size die setting could vary thus giving the user inconsistent results. 5. Insert the case to be trimmed. Push the case and bushing against the compres- sion spring with even pressure until the case bottoms out.
- Page 9 SECTION 3 Operating Instructions 1. The Case Trim Xpress can be mounted to your reloading bench. There are 4 mounting holes that can be used to directly mount the trimmer. The trim- mer can also be used unmounted and hand held against the bench. The trimmer is equipped with non-slip rubber feet that will help prevent the trim- mer from sliding when in use.
- Page 10 4. Main body of trimmer can be wiped with a damp clean cloth if needed. 5. The Case Trim Xpress is provided with a lifetime carbide cutter head, under normal use the cutter will give the user years of clean, consistent cuts.
- Page 11 10. If the Case Trim Xpress is stored in a humid environment or for a length of time you can add a light coat of oil to the Adjuster Barrel and cutter head to prevent corrosion. The internals of the Case Trim Xpress do not require any maintenance, there- fore the housing should not be opened for any reason.
- Page 12 Lyman (Part #7821701) ® 17 Hornet 22 Hornet Bushings Available For Case Trim Xpress Orange Blocks indicate Bushings included with Trimmer (Part #7821704) (Part #7821705) (Part #7821702) (Part #7821703) 300 AAC 30 30 Win 218 Bee .223 Rem .222 Rem 17 Rem Fireball 6.8 Rem SPC...
Need help?
Do you have a question about the Case Trim Xpress and is the answer not in the manual?
Questions and answers