Related Manuals for Triton IVORY 4
Summary of Contents for Triton IVORY 4
- Page 1 IVORY 4 electric shower Installation and operating instructions nstallers please note these InstructIons are to be left wIth the user 2180775H April 2012...
-
Page 2: Table Of Contents
Children may not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. To check the product suitability for commercial and multiple installations, please contact Triton’s specification advisory service before installation. -
Page 3: Important Safety Information
IVORY 4 electric shower PLEASE READ THIS IMPORTANT SAFETY INFORMATION Products manufactured by Triton are safe and without risk provided they are installed, used and maintained in good working order in accordance with our instructions and recommendations. WARNING: DO NOT operate shower if frozen, or suspected of being frozen. It must thaw out before using. -
Page 4: Introduction
Liquid could seep through the joint between the cover and backplate and possibly damage the sealing rubber. Replacement parts can be ordered from Triton Customer Service. See ‘spare parts’ for details and part numbers. -
Page 5: Main Components
6. Solenoid valve 7. Can and element assembly 8. Thermal cut-out - TCO 9. Earth connection 10. Outlet pipe 11. Start/Stop micro switch - Pressure relief device (see page 20) Cover (fig.2) 12. Ivory 4 front cover Inlet Outlet Fig.2... -
Page 6: Electrical Requirements
IVORY 4 electric shower ELECTRICAL REQUIREMENTS Fig.3 Triton Showers, Triton Road, Nuneaton, Warwickshire, CV11 4NR WARNING! W-006-A xxxx THIS APPLIANCE MUST BE EARTHED The installation, supply cable and circuit protection must conform with BS 7671 (IEE wiring regulations) and be sufficient for the amperage required. - Page 7 IVORY 4 electric shower A 45 amp double pole isolating switch with 9.3 In any event, it is essential that individual site conditions are assessed by a competent a minimum contact gap of 3 mm in both poles must be incorporated in the circuit.
-
Page 8: Water Requirements
IVORY 4 electric shower WATER REQUIREMENTS The installation must be in accordance with Water Regulations/Bylaws. Supply Source ............Mains pressure cold water *Minimum running pressure and flow to 100kPa (1.0 bar) at 8 litres per minute ..... the inlet of the shower for full performance for 7.5Kw - 8.5Kw - 9.5Kw... -
Page 9: Siting Of The Shower
IVORY 4 electric shower SITING OF THE SHOWER WARNING! IMPORTANT: If installing onto a tiled wall The shower must not be positioned W-008-A always mount the unit on the surface of the where it will be subjected to freezing tiles. NEVER tile up to the unit. -
Page 10: Fitting The Shower To The Wall
IVORY 4 electric shower FITTING THE SHOWER TO THE WALL Fig.7 WARNING! Check there are no hidden cables or pipes before drilling holes for wall W-005-A plugs. Use great care when using power tools near water. The use of a residual current device (RCD) is recommended. -
Page 11: Pipe Access Points
IVORY 4 electric shower Pipe access points Fig.8 Left hand side top The shower cover has been designed with rear of the backplate two "cut out" bottom pipe access points and the backplate has been designed with one "cut out" top rear - (fig.8) shows the top access "Cut out"... - Page 12 IVORY 4 electric shower If installing a feed pipe from the rear or bottom, Fig.9 the centre of the inlet valve to the wall surface is 21mm (fig.9). Note: If entry is from the rear, the nut of the compression fitting will be partially behind the surface of the wall (fig.9).
-
Page 13: Plumbing Connections
IVORY 4 electric shower PLUMBING CONNECTIONS IMPORTANT Plumbing to be carried out before wiring ENSURE WATER ENTRY PIPEWORK LINES UP • DO NOT use jointing compounds on any WITH SHOWER INLET CORRECTLY BEFORE pipe fittings for the installation. TIGHTENING THE COMPRESSION FITTINGS. -
Page 14: Electrical Connections
IVORY 4 electric shower ELECTRICAL CONNECTIONS SWITCH OFF THE ELECTRICITY SUPPLY AT THE MAINS. Fig.11 shows a schematic wiring diagram. The cable can be surface clipped, hidden or via 20mm conduit. Note: Conduit entry can only be from rear. Route the cable into the shower unit and connect to the terminal block (fig.12) as follows:... - Page 15 IVORY 4 electric shower 1. With the cover off the shower - turn the POWER selector spindle clockwise until the flat section is at the bottom (fig.13). 2. With the cover off the shower - turn the stabi- liser valve spindle fully clockwise until resistance is felt (fig.14).
-
Page 16: Commissioning
IVORY 4 electric shower COMMISSIONING Fig.17 Power selector • Carefully guide the cover onto the backplate to OFF making sure the wires are not trapped. • While applying slight pressure to the front cover, secure in place using the three retaining screws. -
Page 17: Operating The Shower
IVORY 4 electric shower OPERATING THE SHOWER Fig.19 Make sure the commissioning procedure has been carried out. Power selector To start the shower Turn the power selector to either Cold, Economy or High and the water will flow. To stop the shower... - Page 18 IVORY 4 electric shower Note: The preferred knob position on WARNING! ECONOMY will give a different After any servicing of mains water temperature to the same position on HIGH. supply, always flush out the pipework W-002-A To decrease the shower temperature to remove any debris.
-
Page 19: Operating Functions
IVORY 4 electric shower OPERATING FUNCTIONS WARNING! DO NOT use abrasive or aggressive *TP – Temperature Protection W-007-A cleaning products when cleaning the During normal operation if the temperature shower as they may damage the unit. exceeds the showering safety limit the power to the elements will be removed completely, although water will continue to flow. -
Page 20: Instructions For Installers And Service Engineers Only
IVORY 4 electric shower INSTRUCTIONS FOR INSTALLERS AND SERVICE ENGINEERS ONLY CLEANING THE FILTER It is recommended that the filter is periodically cleaned in order to maintain the performance of the shower. It is essential that this operation is carried out by an installer or service engineer. -
Page 21: Spare Parts
IVORY 4 electric shower SPARE PARTS Rear of outlet Ref. Description ..........Part No. Inlet Filter Assembly ..........P22611004 Solenoid Valve ............. P22610801 Stabilising Valve ........... P22640800 Pressure Switch Module ........P22611003 Can Assembly (8.5kW)......... 83314800 Can Assembly (9.5kW)......... 83314810 Can Assembly (10.5kW)........ -
Page 22: Fault Finding
IVORY 4 electric shower FAULT FINDING IMPORTANT: Switch off the electricity at the mains supply and remove the circuit fuse before attempting any fault finding inside the unit. Fault finding Problem/Symptom Cause Action/Cure Shower Interrupted 1.1.1 Blown fuse or circuit breaker. Check inoperable, no power supply. - Page 23 4.2.3 If mains fed, make sure that the mains stopvalve is fully open and there are no other restrictions in the supply while IVORY 4 electric shower shower is in use, or see 4.2.4. X-008-A 4.2.4 Fit pump to give minimum pressure (see rating label).
-
Page 24: Water/Cable Entry Points Diagram
IVORY 4 electric shower Entry Points Diagram Key: Water Entry Points Cable Entry Points... - Page 25 IVORY 4 electric shower...
- Page 26 IVORY 4 electric shower...
- Page 27 IVORY 4 electric shower WEEE Directive – Policy Statement As a producer and a supplier of electric showers, Triton Showers is committed to the protection of the environment via our own environmental policy and the compliance with the WEEE directive.
- Page 28 Triton is a division of Norcros Group (Holdings) Limited E-mail: serviceenquiries@tritonshowers.co.uk Extended Warranty AVAILABLE NOW. Call 0844 980 0740 for more details. 4-12-2012 - 2 yr elec TRITON reserve the right to change product specification without prior notice. E&OE. © TRITON SHOWERS 2013...
Need help?
Do you have a question about the IVORY 4 and is the answer not in the manual?
Questions and answers
where are the 3 cover fixing screws position