Advertisement
Quick Links
PLFY-P
For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner
unit.
Zum sicheren und ordnungsgemäßen Gebrauch der Klimaanlage das Installationshandbuch gründlich durch-
lesen.
Veuillez lire le manuel d'installation en entier avant d'installer ce climatiseur pour éviter tout accident et vous
assurer d'une utilisation correcte.
INSTALLATIEHANDLEIDING
Voor een veilig en juist gebruik moet u deze installatiehandleiding grondig doorlezen voordat u de airconditioner
installeert.
Para un uso seguro y correcto, lea detalladamente este manual de instalación antes de montar la unidad de
aire acondicionado.
Per un uso sicuro e corretto, leggere attentamente questo manuale di installazione prima di installare il condiziona-
tore d'aria.
Para segurança e utilização correctas, leia atentamente este manual de instalação antes de instalar a unidade
de ar condicionado.
English (GB)
Deutsch (D)
Français (F)
Nederlands (NL)
Español (E)
Italiano (I)
Português (P)
Advertisement
Related Manuals for Mitsubishi Electric City Multi PLFY-P VCM-E3 Series
Summary of Contents for Mitsubishi Electric City Multi PLFY-P VCM-E3 Series
- Page 1 PLFY-P English (GB) For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner unit. Deutsch (D) Zum sicheren und ordnungsgemäßen Gebrauch der Klimaanlage das Installationshandbuch gründlich durch- lesen. Français (F) Veuillez lire le manuel d’installation en entier avant d’installer ce climatiseur pour éviter tout accident et vous assurer d’une utilisation correcte.
-
Page 2: Installing The Indoor Unit
1. Safety precautions ..................2 4. Electrical work ...................6 2. Installing the indoor unit ................2 5. Installing the grille ..................9 3. Refrigerant pipe and drain pipe ..............4 6. Test run ....................11 Note: : Indicates an action that must be avoided. tions”. - Page 3 2. Installing the indoor unit (mm) locations (Fig. 2-2) accessory with the grille), make an opening in the ceiling so that the main unit can be installed as shown in the diagram. (The method for using the template and the gauge are shown.) * Before using, check the dimensions of template and gauge, because they change due to fluctuations of temperature and humidity.
- Page 4 2. Installing the indoor unit Suspend the main unit as shown in the diagram. 1. In advance, set the parts onto the suspension bolts in the order of the washers (with insulation), washers (without insulation) and nuts (double). (with insulation) and nuts (double) are to be set later. 2.
- Page 5 Flare nut O.D. Liquid pipe Gas pipe Pipe size Tightening torque Pipe size Tightening torque Liquid pipe Gas pipe (mm) (N·m) (mm) (N·m) (mm) (mm) 49 - 61 49 - 61 34 - 42 34 - 42 Apply refrigerating machine oil over the entire flare seat surface. Wrap the enclosed large-sized pipe cover around the gas pipe, making sure that the end of the pipe cover touches the side of the unit.
- Page 6 1. Remove 2 screws to detach the electric component cover. 2. Route each cable through the wiring intake into the electric component box. (Procure power supply cable and control cable locally.) 3. Securely connect the power supply cable and control cable to the terminal blocks.
- Page 7 Minimum wire thickness (mm²) Local switch (A) Breaker for wiring Total operating current of the indoor Ground-fault interrupter *1 (NFB) unit Main cable Branch Ground Capacity Fuse *1 The Ground-fault interrupter should support inverter circuit. The Ground-fault interrupter should combine using of local switch or wiring breaker. Indoor unit Sample chart Type 1...
- Page 8 indoor unit TB5 is a shielding wire connection. For specifications about the con- necting cables, refer to the outdoor unit installation manual. ler. junction cable. MA Remote controller 2-wire) M-NET Remote controller (Nonpolarized 2-wire) Wireless remote controller (When installing wireless signal receiver) troller board.
-
Page 9: Installing The Grille
5. Installing the grille Accessory name Q’ty Remark Grille Screw with washer 25 (mm) Gauge Fastener Band 5.2. Preparing to attach the grille (Fig. 5-2) relative to the ceiling. If the unit is not properly positioned in the ceiling, there may rectly. - Page 10 5. Installing the grille tach the white glass tube that comes with the main unit so that the tube covers the connector. Close the opening of the glass tube with the band. Fastener (Accessory) White glass tube Connector of the main unit Connector of the grille Band (Accessory) Receiver (for SLP-2ALW)
- Page 11 nals. Warning: The following 3 methods are available. Press to save the setting. Press to return to the previous screen. Press to bring up the Main menu. Operation settings will appear. When the backlight is off, pressing any button turns the backlight on and it will stay lit for a certain period of time depending on the screen.
- Page 12 Test run 1 Press the button to go through the operation modes in the order of “Cool” Test run Remain Remain and “Heat”. (Fig. 6-5) Cool mode: Check the cold air blow off. Pipe Heat mode: Check the heat blow off. Cool Auto * Check the operation of the outdoor unit’s fan.
- Page 17 ■ ~220-240V ~220-240V TB15...
- Page 18 6000 0,01...
- Page 22 Service menu Test run menu Test run Test run Enter maintenance password Input maintenance info. Drain pump test run Function setting Check Self check Service menu: Select: Cursor Cursor...
- Page 23 Test run Remain Remain Pipe Cool Auto Switch disp. Mode Vane...
- Page 24 This product is designed and intended for use in the residential, commercial and light-industrial environment. Importer: Mitsubishi Electric Europe B.V. Capronilaan 46, 1119 NS, Schiphol Rijk, The Netherlands French Branch 25, Boulevard des Bouvets, 92741 Nanterre Cedex, France German Branch...