1. Manuals
  2. Brands
  3. Sherman digitec Manuals
  4. Welding System
  5. DIGITIG 200AC / DC MULTIPRO
  6. User manual

Sherman digitec DIGITIG 200AC / DC MULTIPRO User Manual

Welding rectifier inverter
Hide thumbs
Table of Contents

Advertisement

Quick Links

V1.2 18/08/23
USER MANUAL
Welding RECTIFIER Inverter
DIGITIG 200AC / DC MULTIPRO

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DIGITIG 200AC / DC MULTIPRO and is the answer not in the manual?

Questions and answers

Related Manuals for Sherman digitec DIGITIG 200AC / DC MULTIPRO

Summary of Contents for Sherman digitec DIGITIG 200AC / DC MULTIPRO

  • Page 1 V1.2 18/08/23 USER MANUAL WELDING RECTIFIER Inverter DIGITIG 200AC / DC MULTIPRO...
  • Page 2 WARNING! Before installing and commissioning, please read these instructions 1. GENERAL Commissioning and operation of the device can be made only after a careful reading of this handbook. Due to the continuous development of technical equipment, some of its functions can be modified and operation may differ in detail from the description in the manual.
  • Page 3 Poisoning prevention vapors and gases evolved at the time of welding of coatings for welding electrodes and evaporation of metals: • Use ventilation and exhaust installed in limited air exchange. • Blow fresh air when working in a confined space (tanks) •...
  • Page 4 3. GENERAL DESCRIPTION DIGITIG 200AC / DC MULTIPRO is used for manual welding, and the DC alternating structural steel coated electrodes (MMA method) and quality steels and non-ferrous metals tungsten inert gas (TIG). In the design and construction of equipment we used the latest advances in technology PWM (pulse width modulation) and IGBTs (insulated gate bipolar transistors with gate) so that the welder is characterized by small size and low weight.
  • Page 5 1. A device to be used only in a single-phase, three-wire, with earthed neutral. 2. The inverter units DIGITIG 200AC / DC MULTIPRO are adapted to cooperate with 230V 50Hz fused 25 A time-delayed action. Power supply should be stable, with no voltage drops.
  • Page 6 IGBT Inverter Technology IGBT Inverter Technology DIGITIG 200 ACDC MULTIPRO Current Arc Force Slope Up Down Slope ISTART i = the Base Current PULSE Duty AC Balance AC PULSE Frenquecy frenquency USER H. F H. F ASH% LIFT MEMORY MEMORY TECWELD Peter Polak Sherman 41-943 Piekary Sl.
  • Page 7 8. FUNCTIONAL DESCRIPTION switches and DIAL 8.1 Front and rear panel IGBT Inverter Technology IGBT Inverter Technology DIGITIG 200 ACDC MULTIPRO Current Arc Force Slope Up Down Slope ISTART i = the Base Current PULSE Duty AC Balance AC PULSE Frenquecy frenquency USER ASH%...
  • Page 8 A - button mode selection source (two-stroke engine / czterotakt) Button active only TIG welding. Mode selection is signaled by lighting up symbol symbol symbol symbol symbol dwutaktu mode or the corresponding diode dwutaktu mode or the corresponding diode dwutaktu mode or the corresponding diode dwutaktu mode or the corresponding diode dwutaktu mode or the corresponding diode czterotaktu mode.
  • Page 9 E - Memory settings The device has a memory of the last setting, ie after switching off and then return to the last set parameters. You can also store a total of 20 sets of settings for TIG HF and MMA. To recall previously saved set of settings, press the button until you see the corresponding number set in the display memory (H).
  • Page 10 H - Display memory parameter set USER The display shows the number of the parameter set that was loaded or under the current set will be saved. I - display of welding parameters REMOTE ASH% The display shows the parameters during setup and during welding. The illumination of the corresponding LED on the side of the display indicates a unit parameter.
  • Page 11 ARC FORCE ARC FORCE allows the arc. Shortening the length of the arc is accompanied by an increase in the welding current, which results in stabilizing the arc. Decreasing the value will give a soft arc and a smaller depth of penetration, while increasing the value results in deeper penetration and the possibility of short-arc welding.
  • Page 12 10.2.1 arc initiation and conduct of TIG welding HF Device DIGITIG 200AC / DC MULTIPRO equipped with the ionizer enabling non-contact arc ignition. To ignite the arc mode dwutaktu must approach the electrode to the workpiece at the distance of 2 millimeters and press the button in the...
  • Page 13 welding the lead button is pressed. Releasing the button on the handle causes the start of the current phase of descent and ending the welding process. To ignite the arc mode czterotaktu must approach the electrode to the workpiece at the distance of 2 millimeters and press the button on the handle of the torch to turn the ionizer.
  • Page 14 10.2.4 TIG mode 4T : 10.2.4 TIG mode 4T : • Press and hold the handle. Starts the flow of protective gas; • 0 ~ t1 : Time gas pre. Can be adjusted in the range of 0 ~ 1.0 sec; 0 ~ t1 : Time gas pre.
  • Page 15 12. OPERATION MANUAL Operation of the device DIGITIG 200AC / DC MULTIPRO should take place in an atmosphere free of corrosive components and dusty. Do not place the device in dusty, near the working grinders, etc. Dust and pollution control boards metallic filings, wires and connections inside the unit may cause an electrical short, and consequently damage to the welding machine.
  • Page 16 The device should be stored at -10 ° C to + 40 ° C and relative humidity 80% free of corrosive fumes and dusts. Transportation of packaged devices should be covered means of transport. For transport the packaged unit must be secured against slipping and ensure the correct position. 15. COMPLETE SPECIFICATION 1. Source DIGITIG 200AC / DC MULTIPRO 1 piece. 2. Holder for TIG welding 1 piece.
  • Page 17 17. GUARANTEE Guarantee granted for a period of 12 months for business entities or consumers for 24 months from the date of sale. The guarantee will be respected by the advertiser after the presentation of proof of purchase (invoice or receipt) and warranty card inscribed with the product name, serial number, date of sale and point of sale bearing the stamp.

  • Page 18: Declaration Of Conformity

    41-909 Bytom ul. 3 Cross POLAND Declare that the said product: inverter welder Trade name: DIGITIG 200AC / DC MULTIPRO Type: TIG 200P AC / DC Manufacturer's trademark: to which this declaration relates complies with the following directives of the European Union and...

Table of Contents

Save PDF