Table of Contents
Advertisement
Easy Set-Up Instructions
• Note this unit has already been programmed at the factory.
All you need to do is program a phone number to dial.
• Call the EMS5 unit or use your Master Station phone.
• Enter **08601 you will hear three beeps.
• Enter *03 (number to dial) # you will hear three beeps.
• Enter # # to exit programming.
For other programming options refer to manual.
Janus is a brand of Avire
984-0013-03
EMS5 Call Director
Avire Inc
415 Oser Avenue, Suite Q, Hauppauge, New York 11788
Phone: 631 864 3699 Toll Free: 800 527 9156
Fax: 631 864 2631 Email: sales.us@avire-global.com
www.avire-global.com
www.januselevator.com
i
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for AVIRE Janus Call Director EMS5
- Page 1 For other programming options refer to manual. Avire Inc 415 Oser Avenue, Suite Q, Hauppauge, New York 11788 Phone: 631 864 3699 Toll Free: 800 527 9156 Fax: 631 864 2631 Email: sales.us@avire-global.com www.avire-global.com www.januselevator.com Janus is a brand of Avire...
- Page 2 Installation Instructions Model No: EMS5 Avire Inc 415 Oser Avenue, Suite Q, Hauppauge, New York 11788 Phone: 631 864 3699 Toll Free: 800 527 9156 Fax: 631 864 2631 Email: sales.us@avire-global.com www.avire-global.com www.januselevator.com Janus is a brand of Avire 984-0013-03...
- Page 3 Wiring Diagram 984-0013-03...
-
Page 4: Table Of Contents
TABLE OF CONTENTS SECTION TITLE PAGE WIRING AND LAYOUT CONSIDERATIONS INSTALLATION INSTRUCTIONS PROGRAMMING INSTRUCTIONS PROGRAMMING THE EMS5 TO PLAY VOICE MESSAGES ADDITIONAL PROGRAMMING COMMANDS EMS5 ONBOARD DISPLAY CODES PROGRAMMING INSTRUCTIONS FOR HANDSFREE PHONES CONNECTED TO EMS5 VIII OPERATING INSTRUCTIONS OPERATING FAQ’s TROUBLESHOOTING GUIDE MOUNTING DIAGRAM SPECIFICATIONS... -
Page 5: Iwiring And Layout Considerations
WIRING AND LAYOUT CONSIDERATIONS 1. Wiring from the EMS5(s) to Elevator Phones or phone devices: You will need one pair of wires from each elevator phone (or phone device) to the EMS5(s). Cabling can be telephone communication cable, which is normally 20-22 gauge twisted pair. -
Page 6: Installation Instructions
INSTALLATION INSTRUCTIONS 1. Ideally, it is best to mount each EMS5 Call Director™ side by side. This will reduce field-wiring problems. 2. Use the 3-Keyholes on the back-box case of the EMS5 to mount the unit on a dry or concrete wall. - Page 7 6. Plug in the connector for the battery to the P1 connector 7. Mount the EMS5 unit on the wall using the 3-keyhole pattern holes on the back box and close back the front cover. 8. Plug in the power supply, the LED labeled “COM-ERROR” (on the Master EMS5 only) will start flashing and quit after 30 seconds.
-
Page 8: Programming Instructions
PROGRAMMING INSTRUCTIONS The EMS5 is pre-programmed at the factory to function as an intercom system. It will work using all the default codes described in this manual. There is no need for additional programming. If you are planning to connect a phone line to the unit then you must follow the programming instructions below: ACCESSING PROGRAMMING MODE There are three methods you can use to program the EMS5 call director. -
Page 9: Programming The Ems5 To Play
b. * 02 followed by the second phone number to be dialed, # to end c. * 03, followed by the third phone number to be dialed, # to end PROGRAMMING THE EMS5(s) TO DIAL ON A RING-DOWN LINE Follow the steps below to program the EMS5 for a Ring down line: a. -
Page 10: Vadditional Programming Commands
• Note: Outgoing messages will start to play only on an outgoing call from an elevator port when the voice detection circuit of the EMS5 detects that the call has been answered and the call waiting beeping stops. • Note: Incoming messages will start to play only on an incoming call when the EMS5 is set up to answer incoming calls and after it plays the diddle- diddle sound. - Page 11 re-connected. The AUX1 will also re-open if the unit is reset. If there are multiple EMS5 call directors only the AUX1 of the master EMS5 needs to be connected. *5 D E F # - Optional programming command, Default *5000#. •...
-
Page 12: Ems5 Onboard Display Codes
If the Hang up command was “#*”, you must program: *873(#*) # *Note: The EMS5 will send the Hang-up tones in all of the following cases: 1. When the EMS5 detects the CPC from the line. 2. When the User hangs up the phone connected on Local Service Port. *880# - Disables Call Progress Tones –... -
Page 13: Programming Instructions For Handsfree Phones Connected To Ems5
CPC: CPC Signal Detected. LB: LOW or BAD BATTERY XX: ACTIVE CALL FROM AN ELEVATOR (XX=01-64). Note: If more then one Elevator is active the Display should show all numbers and switch between each number every second. Example: Ports1, 3, 6 became active. Display should show 01 then 03 then 06 then back to 01, 03, 06 and so one... - Page 14 4. Press “0” to alert hearing impaired passenger with blinking light. 5. At end of call, hang up handset. RECEIVING A CALL FROM THE ELEVATOR PHONE AT THE ANSWERING SERVICE: 1. The operator picks up handset to answer incoming call. 2.
-
Page 15: Operating Faq's
CALLING AN ELEVATOR PHONE FROM THE ANSWERING SERVICE 1. Operator dials the phone number that the EMS5 is connected to. 2. The Master Station phone will ring and if the attendant is there they will pick up. 3. If the operator needs to call directly to an elevator without talking to the attendant they should dial “*”... -
Page 16: Xtroubleshooting Guide
NO - CHECK TELCO LINE FOR DIAL TONE. • IS DIAL TONE PRESENT? YES - REPLACE THE EMS5. NO - CONTACT THE TELEPHONE COMPANY. If you have any questions or problems, please call Avire technical support for assistance at 1-800-527-9156. 984-0013-04... -
Page 17: Mounting Diagram
MOUNTING DIAGRAM (Diagram not drawn to scale) 984-0013-04... -
Page 18: Specifications
SPECIFICATIONS MECHANICAL Size: 8 3/8”W X 14 1/8”H X 2 5/16”D Weight: 9 lbs ELECTRICAL Phone line requirements: (TELCO) Standard (analog) loop start voice grade touch-tone telephone line, PBX or key system station analog telephone line. 120VAC to 16-18 AC Power: (Transformer supplied) VAC @ min. -
Page 19: Warranty Policy
If trouble is experienced with this equipment, NFLTE02B33770 for repair or warranty information, please contact Avire at 1-800-527-9156 or e-mail at www.januselevator.com. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Need help?
Do you have a question about the Janus Call Director EMS5 and is the answer not in the manual?
Questions and answers