Advertisement
Quick Links
Advertisement
Related Manuals for BIOMET Clotalyst
Summary of Contents for BIOMET Clotalyst
- Page 1 Artist Proof: 01-15-10 Clotalyst ® Autologous Serum Collection System...
- Page 2 Clotalys t Autologous Serum ® • The kit is designed for the preparation of autologous serum that is to be mixed with PRP and autograft or allograft for bone graft handling prior to application to an orthopedic surgical site. • The Clotalyst Autologous Serum Collection System produces approximately 6ml of ® autologous serum from only 12ml of patients’ own citrated blood. The serum output can be mixed with platelet rich plasma (PRP) produced by the GPS III system. ®...
- Page 3 Clotalys t Autologous Serum ® Platelet gel derived from the GPS III System in combination with Clotalyst Autologous Serum ® ® • The Clotalyst Kit includes GPS III disposable and all components necessary ® ® to produce PRP. • The Clotalyst System is designed to clot PRP in less than 15 seconds. ® • The kit produces 6ml of PRP and 6ml of Clotalyst autologous serum. ®...
- Page 4 Note: Leave grey stopper on opposite end of reagent syringe when attaching plunger. Remove grey stopper on reagent syringe. Unscrew blue cap on port No. 2 of disposable and attach reagent syringe. While holding the Clotalyst ® disposable vertically, inject all of reagent. Remove the reagent syringe from the disposable. Remove protective cover on white cap and discard. Screw the...
- Page 5 Technique (continued) Step 2: Load (continued) Unscrew red cap on port No. 3 and attach syringe containing 12ml of citrated blood. While holding disposable vertically, inject all blood. Remove the empty syringe. Remove protective cover on the white cap and discard. Screw white cap onto port No. 3.
- Page 6 Step 3: Incubate Gently mix by inverting disposable at least 12 times (without producing foam). Preheat Clotalyst heater 10 minutes prior to use. ® Place disposable into Clotalyst heater. The glass ® beads inside the disposable should be distributed evenly when it is placed into the heater. Press the incubation button to start cycle. When the incubation cycle is complete (25 minutes), the heater will beep four times.
- Page 7 Technique (continued) Step 4: Spin Preparation (Counter Balance) Place Clotalyst disposable in the centrifuge with the ® empty Clotalyst orange counterbalance (800-0760) ® in the opposite side of the centrifuge. Step 5: Spin Close centrifuge lid and set speed to 3200 RPMs and time to 5 minutes. Press green button to start centrifuge cycle. Once cycle is complete, press red button to open lid. Step 6: Autologous Serum Extraction Gently remove the disposable from the centrifuge without disturbing the stratified layers. Unscrew the...
- Page 8 Technique (continued) Step 6: Autologous Serum Extraction (continued) To maximize harvest volume, the disposable may be tilted towards port No. 3 as autologous serum is extracted. Step 7: Storage Store Clotalyst autologous serum at 18–26°C (64– ® 78ºF) for up to 4 hours prior to use. Discard remaining serum if not used within the provided time frames.
- Page 9 Clotalys t System Ordering Information ® Clotalyst System ® Description Catalog Number Clotalyst Kit includes GPS III Separator with Blood Draw and Reagent ® ® 800-0722 800-0723 Clotalyst Kit includes GPS III Mini Separator with Blood Draw and Reagent ® ® Clotalyst Heater (Heater Cord included) 800-0755 ® Clotalyst Non-Sterile Counterbalance (Not included in Clotalyst kit) 800-0760 ® ® Drucker 230 Volt 50-60Hz Centrifuge 755VES Accessories Description Catalog Number...
- Page 10 4. sPiN: Close centrifuge lid. Set RPM to 3.2 (x1000) and the time to 15 minutes. Press the start button. Once spin is complete, open the centrifuge Please note: the ACD-A and Clotalyst™ Reagent included in this kit are only for and remove the GPS™ III Separator.
- Page 11 PROCEDURE ONE: Use of GPS™ III Mini Separator to prepare platelet-rich that may be present in the separator. Place the Clotalyst™ Separator in a plasma (PRP)(Figure 1) Biomet Biologics™ centrifuge. 8. BALANCE: Place the orange Clotalyst™ counterbalance (800-0760) 1. DRAW: Draw 3ml ACD-A into 30ml syringe. Attach to 18-gauge apheresis directly opposite from the Clotalyst™...
- Page 12 All trademarks herein are the property of Biomet, Inc. or its subsidiaries unless otherwise indicated. This material is intended for the sole use and benefit of the Biomet Biologics sales force and physicians. It is not to be redistributed, duplicated or disclosed without the express written consent of Biomet. For product information, including surgical techniques, indications, contraindica- tions, warnings, precautions and potential adverse effects, see the Biomet Biologics website at www.biometbiologics.com P.O. Box 587, Warsaw, IN 46581-0587 • 800.348.9500 x 1501 ©2010 Biomet Orthopedics • biomet.com Form No. BBI0039.1 • REV053110...
Need help?
Do you have a question about the Clotalyst and is the answer not in the manual?
Questions and answers