Advertisement
Advertisement
Table of Contents
Summary of Contents for PVI VuMATRIX-FX
- Page 1 VUMATRIX FX HDMI OVER IP MATRIX EXTENDER QUICK START GUIDE QUICK START GUIDE...
-
Page 2: Product Specifications
Pro Video instruments PRODUCT SPECIFICATIONS Transmitter: Power Supply 12V – 1.5A DC, 600 mA typical consumption Power over Ethernet POE 802.3af Dimensions 210 x 123 x 40 mm Weight 680 g HDMI Video Support Up to 4K UHD 4:4:4 @30Hz HDCP Compliance HDCP 2.2 HDMI Audio Support... - Page 3 Pro Video instruments CONFIGURE TRANSMITTER OUT OF BOX USING REMOTE CONTROL: 1) Power on the unit by connecting the power supply cable. Allow the unit 2 minutes to boot, until the ON LED light is lit solid green, and the On Screen Display shows a number (Transmitter ID, 0 by default). 2) On the Remote, press the POWER and 7 keys together to put the remote in Transmitter Mode.
- Page 4 Pro Video instruments CONFIGURE RECEIVER OUT OF BOX USING REMOTE CONTROL: 1) Power on the unit by connecting the power supply cable. Allow the unit 2 minutes to boot, until the ON LED light is lit solid green, and the On Screen Display shows a number (Transmitter ID, 0 by default). 2) On the Remote, press the POWER and 8 keys together to put the remote in Receiver Mode.
- Page 5 3) Power on the Receiver and allow to boot. Connect your TV to the receiver via HDMI Out. With the TV set to the HDMI input, you will see the PVI test screen and “Waiting for Transmitter” message. 4) Connect the CAT5e or CAT6 link cable to the UTP LAN ports of the Transmitter and Receiver. Once connection is established, the UTP and LINK lights will be solid.
- Page 6 Pro Video instruments GIGABIT SWITCH CONNECTION GUIDE Gigabit Switch configuration allows you to combine any number of transmitters and receivers that can be supported by your network switch. If using POE, it is not necessary to connect the power adapter of the transmitters or receivers.
-
Page 7: Appendix A: Changing Ip Address Of Transmitter/Receiver
Pro Video instruments APPENDIX A: CHANGING IP ADDRESS OF TRANSMITTER/RECEIVER NOTE: If the default IP address is changed and then the address is lost, refer to Appendix C for direction on how to reset the unit to factory defaults. To change the IP address of an individual Transmitter or Receiver: •... -
Page 8: Appendix B: Gigabit Switch Recommended Settings
Pro Video instruments APPENDIX B: GIGABIT SWITCH RECOMMENDED SETTINGS The VuMATRIX FX system requires that all transmitters and receivers must be connected to the same network (VLAN) with a Gigabit Switch (or switches), and a Gigabit Wi-Fi Router (if using the VuMATRIX FX Control App). The Gigabit Switch MUST support Multicast Layer 2, IGMP, and Jumbo Frames. -
Page 9: Appendix C: Factory Reset
Pro Video instruments APPENDIX C: FACTORY RESET NOTE: Only perform these steps if needed to recover if the IP address is lost, or as directed by PVI Technical Support. Using the Remote: 1) If resetting the Transmitter, press Power + 7 on the remote to put it in Transmitter Mode. If resetting the Receiver, press Power + 8 to put the remote in Receiver Mode. - Page 10 Pro Video instruments TECH SUPPORT – CONTACT US For any needs not covered in this Quick Start Guide, visit www.pvisupport.com, and look for VuMATRIX FX under “Knowledgebase”. Should you need any additional support, to submit a support ticket, please go to www.pvisupport.com and click “Submit a Ticket”.
Need help?
Do you have a question about the VuMATRIX-FX and is the answer not in the manual?
Questions and answers