Summary of Contents for Cosentino Silestone
- Page 1 Silestone ® Manual for Professional INTENDED FOR: MARBLE WORKERS, PROFESSIONAL FITTERS, AND ARCHITECTS On Top...
-
Page 2: Table Of Contents
Content FABRICATION CUTTING PRECAUTIONS EDGES GENERAL SAFETY ADVICE TECHNICAL DATA ABRASIVES POSITIONING CHART INSTALLATION PROFESSIONAL CLEANING AND MAINTENANCE TECHNICAL ADVICE REPORT... -
Page 3: Fabrication
Fabrication Color Where more than one slab is required to make Table Nº the kitchen worktop, check that the slabs match in colour and appearance by putting them together. Dimensions To do this, the information on the specifications Factory Date label for each slab should be used. -
Page 4: Precautions
To cut a Silestone® slab or one for ECO by Cosentino®, the first cut should The cutting disk should be perfectly aligned with the cutting direction. be made along the length of the slab, and the second on the width, as Rotational speed: 2500 rpm for 20 cm radius disk;... -
Page 5: Edges
The trays with the concentric coupling screw directed towards the polishing area to keep authorised by Cosentino. are used for straight edges, whether it is the material cool and prevent it from burning. -
Page 6: General Safety Advice
Always pay attention to the safety and prevention Do not eat, drink or smoke while using it. measures set out in the “Guide to Good Practice for working with Silestone® and ECO by Cosentino® Cosentino® does not accept responsibility for any products” manufactured by Cosentino®. -
Page 7: Abrasives Positioning Chart
Abrasives Positioning Chart Straight Edge PRESSURE GRAIN SPEED PRESSURE COUNTERPRESSURE position 70 cm/min 1,2 Bar 1 Bar position 70 cm/min 1,2 Bar 1 Bar position 70 cm/min 1,2 Bar 1 Bar position 70 cm/min 1,2 Bar 1 Bar position 70 cm/min 1,2 Bar 1 Bar position... -
Page 8: Installation
Step 7 Step 8 Step 9 Use “Juntax” pigments, solumastic and Silestone® y ECO by Cosentino® cannot be Supply your customer with a Cleanpack Colorsil silicones, to achieve smooth, fitted between walls, furniture, etc. Allow (Care kit) to ensure correct use of the even joints in the worktop. -
Page 10: Professional Cleaning And Maintenance
Cleaning & Maintenance Prevention For the correct manufacturing and fitting of Silestone®, it is important to take increased precautions, in order to speed up working times and avoid unnecessary cleaning and stains. Below, we have included two good practice procedures to be followed during fitting:... -
Page 11: Technical Advice Report
Technical Advice Report The recommendations and proposals in this including risk assessments, planning corrective document should only be used as guidelines actions, specific technical advice reports, for the implementation of the organisational, training and information, preventative technical measures and individual habits. medicine etc, which correspond to the health Under no circumstances should the specified and safety departments of the companies or... - Page 12 * To check terms and conditions please go to www.silestone.com COSENTINO HEADQUARTERS Ctra. Baza a Huércal-Overa, km 59. 04850 Cantoria, Almería (Spain) +34 950 444 175 info@cosentino.com www.cosentino.com www.silestone.com F SilestonebyCosentino T @Silestone_ESP V 04/2018...
Need help?
Do you have a question about the Silestone and is the answer not in the manual?
Questions and answers
With a large double under mount stainless kitchen sink should there be supports and can there be a seam in the middle of the sink? Does the seam that goes to the faucet compromise the gasket of the faucet in any way?
Yes, the area around the sink must be solid and properly supported to prevent bowing. A seam in the middle of the sink is not recommended, as it could compromise the faucet gasket.
This answer is automatically generated