Table of Contents
Advertisement
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
Do not unpack any contents until you verify all requirements on PAGE 3.
If you have any questions, visit MantelMount.com or call
WARNING!
!
This product contains small parts that can be a
choking hazard. Do not let children play with any of
these small parts! Keep children away from the work
area during installation.
WARNING!
!
Do not let children operate, pull on, or hang from
MantelMount.
Do not operate MantelMount when anyone is near or
behind the mount. MantelMount is very strong and can
result in crushing injuries.
WARNING!
!
MantelMount must be installed to a wall or structure
that is able to hold five times the combined weight of
all equipment. If you are unsure about your structure,
a contractor must evaluate your installation.
WARNING!
!
Exceeding the weight capacity can result in
serious personal injury or damage to equipment!
The combined weight of all components must not
exceed 125 lbs (57 kg).
IMPORTANT:
MantelMount has three different adjustments
that must be made after the installation is
complete in order to operate properly.
The side-to-side swivel stops are
adjusted with two screws with
locknuts so that the TV does not
swivel into the mantel.
Tilt is removed with two screws on
each side of the swivel mechanism.
The TV should always be
vertically parallel to the wall
The bottom travel stop is adjusted
with two screws and locknuts so
the TV and mount do not lower all
the way into the mantel.
MantelMount MM860
MM860 Installation Instructions
Please read this entire manual before you begin.
www.MantelMount.com
(800)-897-9755.
!
CAUTION:
This product is intended to be installed by
professional installation contractors, or persons
familiar with the tools and methods required for
this installation. If you are not sure about your
ability to perform this installation, you must
contact a professional. MantelMount is not
responsible for damage or injury caused by
incorrect installation or improper use.
!
CAUTION:
Do not use this product in any way, or for any
purpose, that is not specifically described in these
instructions. MantelMount is not responsible for
damage or injury caused by incorrect installation
or improper use.
U.S. Pat. No. 8,864,092
Other Patents Pending
PAGE 1
Advertisement
Table of Contents
Related Manuals for MantelMount MM860
Summary of Contents for MantelMount MM860
- Page 1 IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE 3. If you have any questions, visit MantelMount.com or call (800)-897-9755. WARNING! CAUTION:...
- Page 2 Before you begin, please verify that all components are included and undamaged. If any parts are missing or damaged, contact MantelMount. Never proceed with missing or damaged parts! Lay out all components and make sure you identify that each one has a match in the diagram.
- Page 3 Please verify that your installation meets all of these CRITICAL requirements: MantelMount is designed for use only with decorative Wall must be WOOD STUD FRAME only. There must be at fireplaces that are not the primary heat source for a least 2 studs available for mounting.
- Page 4 {12} {12} {03} {10} {12} {05} {10} {04} {10} {12} {12} {12} {06} {10} Should be more than Fixed 8 INCHES 8 INCHES {12} {27} {27} {08} {11} {07} {11} {12} {12} {30} {12} {09} {11} PAGE 4 MantelMount MM860...
- Page 5 Bottom of Vertical Brace Vertical Brace {16} {59} 8 to 11 INCHES MORE THAN {16} 8 INCHES {19} Bottom of TV Bottom of Sound Bar Use this distance in Step 9 {29} {59} For Sound Bar Only MantelMount MM860 PAGE 5...
- Page 6 TV to the top of various mantel sizes. However, the MM860 Lift Housing {30} is often located even higher on the wall than the TV. To locate the TV so it has enough clearance and doesn’t hit the mantel, you will need to know how much higher the Housing is than the bottom of the TV.
- Page 7 CAUTION: MantelMount MM860 comes with an RF Remote Control. This Remote does not need to be pointing at the mount in order to control the mount; in fact, the Remote will send commands to the mount even from other rooms in the house. It is very important to operate the Remote only when the mount is in sight.
- Page 8 Adapter Brackets for 2x4 bracing: (view facing the wall) MM860 includes brackets that make it easier to install horizontal 2x4 bracing inside the wall. This is because all the attachment holes in the brackets can be reached for drilling 1.5"...
- Page 9 Lag Bolts through the holes in the front flange of the Lift Housing {30}. Any studs that were cut can be reattached to the new sections of 2x4. {20} {17} {13} {11} {13} {11} MantelMount MM860 PAGE 9...
- Page 10 Step 9. Use a level to ensure the cutout is plumb. DOWN Button: Lowers the Mount NON-RECESSED: Use the Cardboard Template to mark the location of the Housing. MantelMount is located in the same spot for all installations. Distance from mantel to opening...
- Page 11 Return to STEP 18 for other side. Proceed to Step 19 to set the Soft Stop. d. Press the Program Button after the Soft Stops are set in order to exit Program Mode. Repeat for the other side. MantelMount MM860 PAGE 11...
- Page 12 CAUTION: Auto Raising Heat Monitor (ARHM): Never allow children to play around, hang from, This unique safety feature of the MantelMount MM860 will or operate MantelMount. Property damage or monitor the temperature above your fireplace at all times and personal injury can occur.
- Page 13 Ensure that cables do not get pulled or pinched between brackets These covers can be used to hide cables when the mount is raised. that are routed through the Housing. Cable Cover {60} simply pulls open. Access Cover {32} requires removing two screws {18}. MantelMount MM860 PAGE 13...
- Page 14 • PC or laptop can manually upload the latest Firmware to the MM860 if needed • MM860 can be configured in a web browser using the default IP Address 192.168.150.111 • The MM860 Utility and latest firmware must be loaded onto the PC or Laptop before Installation Optional:...
- Page 15 MantelMount MM860 Utility Software Package (3 Modules): This utility must be loaded onto a PC or laptop in order to configure the MantelMount MM860 The MM860 Utility and MM860 Firmware are available for download at MantelMount.com - (Dealer) MM860 Utility...
- Page 16 Automation System to set up the MM860. Drivers are located at MantelMount.com (Dealers) Completed Scan Open the Configuration Module: Use the “Device” Page to adjust the MM860 parameters if needed. These settings are stored onboard the MM860. Module 2: MM860 Configuration Module 2:...
-
Page 17: Remote Control
Memory 1 position. When the TV is turned o , the TV Status: MM860 will wait up to 10 seconds to be sure, then raise the mount. ALPS TV Settings: (Auto Lowering Power Sensing): If the ALPS feature is false triggering, verify what the TV is actually using... - Page 18 PAGE 18 MantelMount MM860...
- Page 19 MantelMount MM860 PAGE 19...
-
Page 20: Customer Service
Monitors the temperature and raises Full Manufacturer Warranty: the TV automatically if the temp. behind the TV is above 130°F MantelMount will replace or repair any product or part that proves defective due to improper workmanship Patent Pending or material during the warranty period.
Need help?
Do you have a question about the MM860 and is the answer not in the manual?
Questions and answers