Installing The Extractor - Caple DD606BK Instruction Manual

I N S T A L L I N G T H E E X T R A C T O R
1. Before carrying out the appliance installation, please check that
all components are not damaged, in such a case contact your
retailer and do not carry out any installation operation.
Before the installation of the Downdraft, please remove the
safety piece you can see in the picture (Fig.1). Furthermore,
please read carefully all of the following installation instructions.
- Use an air exhausting pipe whose maximum length does not
exceed 5 meters.
- Do not use flexible ducting.
- Limit the number of elbows in the piping, since each elbow reduces the air capacity of 1 linear
meter. (eg. if you use no. 2 x 90° elbows, the length of piping should not exceed 3 meters).
- Avoid abrupt direction changes.
- Use a 150mm constant diameter rigid ducting pipe for the whole length (or equal surface area).
- Only use ducting approved by the standards in force.
The manufacturer shall not be deemed responsible for air capacity or noise problems caused by
failure to comply with the above instructions and no warranty on the product shall be provided.
2. Before making the hole, check that there are no structural or other parts inside the cabinet,
where the appliance is to be placed, which could hinder a proper installation. Check that the
dimensions of the Downdraft and the ones of the hob are compatible with the cabinet so that
the installation can be carried out properly.
3. Make a rectangular opening in the back part of the cook top
(842x100mm for the 90cm model and 542x100mm for the 60cm
model). If the DDMEXT10 is already installed, remove the screws
and the motor in order to insert the downdraft in the hole made.
4. Put the Downdraft in the opening, inserting it from above as
shown in (Fig. 2).
5. Fix the downdraft inside the cabinet, using the special fixing
brackets supplied with the product (Fig. 3). Insert the brackets in
the lower side of the downdraft (Fig. 3), in such a way that there
is a 2mm distance between the lower side of bracket and the
bottom of the cabinet (Fig. 3).
This distance will allow the traction to be positioned downwards
of the product, at the moment of fixing, in order to have the
stainless steel trim perfectly adhering with the work surface.
Before inserting the screws, please make sure that the appliance
is perfectly perpendicular with the work surface.
2 mm
8 Instruction manual DD606BK
Please keep this instruction manual for future reference
1
2 mm
3
2 mm
16
5
16
1
1 2
2 mm 3
3 4
6. Once the installation is complete and after connecting the appliance to the mains power, lift up
the downdraft and remove the door block (Fig. 4); then open the door (Fig. 5) and fit the filters
in place (Fig. 6). In the version of the Downdraft using the the DDMEXT10, install the power
unit orienting the air outlet to the desired position, either downwards or upwards (Fig. 7). The
motor can be installed either on the front or rear side of the downdraft. After having installed
1 2
the motor, then connect the air ducts.
2
3 4
16 16
4
7. For versions using an external motor, place the external motor in a suitable area and fit the
exhaust air flue as illustrated. Then fit the air outlet ducts between the external motor and the
downdraft. Select an air outlet from the five possibilities (Fig. 8) and fit the union supplied with
the appliance.
8. Place the metal box containing the wiring in an easily accessible area to allow maintenance
interventions where necessary (Fig.9). Connect the connectors (9-pole connector) to control the
actuator and safety control and button pad connector (Fig. 10).
6
5
6
7
7
7 7
2
9
9
9 9
4
Please keep this instruction manual for future reference
1 1
3 3
2 mm 2 mm
5 5
8
8
8 8
10
10
10 10
Instruction manual DD606BK
2 2
4 4
6 6
9