Download
Share
Print this page
Beninca CP.BULL8 OM Manual
  1. Manuals
  2. Brands
  3. Beninca Manuals
  4. Gate Opener
  5. CP.BULL8 OM
  6. Manual
Beninca CP.BULL8 OM Manual

Beninca CP.BULL8 OM Manual

Hide thumbs Also See for CP.BULL8 OM:

Advertisement

Quick Links

Download this manual See also: Manual
L8542646
03/2013 rev 1
CP.BULL8 OM
UNIONE NAZIONALE COSTRUTTORI
AUTOMATISMI PER CANCELLI, PORTE
SERRANDE ED AFFINI

Advertisement

loading
Need help?

Need help?

Do you have a question about the CP.BULL8 OM and is the answer not in the manual?

Questions and answers

Related Manuals for Beninca CP.BULL8 OM

Summary of Contents for Beninca CP.BULL8 OM

  • Page 1 L8542646 03/2013 rev 1 CP.BULL8 OM UNIONE NAZIONALE COSTRUTTORI AUTOMATISMI PER CANCELLI, PORTE SERRANDE ED AFFINI...
  • Page 2 ENCODER 230V: T0,315 115V: T0,5 J1 DAS Close DAS 8K2 SHIELD J1 DAS Open DAS N.C. 230V: T0,315 115V: T0,5 BLINK LAMP 230Vac BLINK TRASF 230V: F5A 115V: F10A...
  • Page 3 2ch:ON 2ch:Off 2ch:Off SCA 24Vac Service IIch serl:Off serl:Off serl:on 3W max Light Radio 230V tst1:Off tst1:Off tst1:Off Relè 24Vac tst2:Off tst2:Off tst2:Off 24Vac COM NC 24Vac 24Vac COM NC 24Vac 2ch:Off serl:Off tst1:On tst2:On...
  • Page 4 EC Declaration of conformity Declaration pursuant to Directives 2004/108/EC(EMC); 2006/95/EC(LVD) Manufacturer: Automatismi Benincà SpA Address: Via Capitello, 45 - 36066 Sandrigo (VI) - Italy Declares that the product: Command central for 1 230 Vac motor, for sliding doors: CP.BULL 8OM is compliant with the conditions of the following EC Directives: •...

  • Page 5: Technical Data

    WIRE DIAGRAM Wire connections shown in Fig. 1 are described hereunder: Terminals Function Description CP.BULL8 OM: Input, 230Vac 50Hz (L-Phase/N-Neutral) Power supply CP.BULL8 OM 115: Input, 115Vac 60Hz (L-Phase/N-Neutral) Earth (compulsory) Connection antenna to the built-in receiver ANT/SHIELD Antenna (ANT-signal/SHIELD-screen). +12V COMMON Common for control inputs.
  • Page 6 COM (+12V) Common for limit switches. 12-0-12 Secondary Connection of secondary winding of 24V transformer Motor connection, 230Vac – single phase: M1/COM/M2 Motor M1-Phase/ COM-Common/ M2-Phase CAP/CAP Capacitor Connection to capacitor FLASH/FLASH Flashing light Connection to flashing light, 230Vac 40W max. TRASF Primary Connection to transformer primary winding...
  • Page 7 The intervention threshold of the anti-crashing device (Encoder) during braking is adjusted *. SEAR 0-99-(0%) 99:maximum sensitivity - 0: minimum sensitivity Activated only with SERL:ON Logic. The activation time of the service light is adjusted. 1-240-(60s) The force of the motor brake is adjusted. Ibra 0-99-(50%) 0: disabled braking - 1:minimum braking - 99: maximum braking...
  • Page 8 Check of photocells on PHOT O input is enabled or disabled. TST1 On: check is enabled. If check is not successful, no operation is enabled. (OFF) Off: AUX output can be preset as SCA, or by 2CH, SERL and TST2 logics. Check of photocells on PHOT C input is enabled or disabled.
  • Page 9 MAINTENANCE CYCLES (maci) This function enables to activate the maintenance request notice after a number of manoeuvres determined by the installer. To activate and select the number of manoeuvres, proceed as follows: Press button <PG>, the display will show OFF, which indicated that the function is disabled (default value). With the buttons <+>...

  • Page 10: Error Messages

    DIAGNOSTICS In the event of malfunctions, by pressing key + or - the status of all inputs (limit switches, control and safety) can be displayed. One segment of the display is linked to each input. In the event of failure it switches on according to the following scheme. P.P.
  • Page 11 AUTOMATISMI BENINCÀ SpA - Via Capitello, 45 - 36066 Sandrigo (VI) - Tel. 0444 751030 r.a. - Fax 0444 759728...