Related Manuals for Staber Industries HXW2304
Summary of Contents for Staber Industries HXW2304
- Page 1 STABER CLOTHES WASHER HXW2304 HXW2305 HXW2404 HXW2405 HXW2504 HXW2505 Operator’s Manual Installation/Operation/Maintenance/Parts Part Number 818235 Printed in USA...
- Page 2 FORWARD We are pleased that you have selected a Staber clothes washer as one of your appliances. Your clothes will be washed using a tumble action inner tub. Please register your new Staber washer on our Internet web site, www.staber.com. An average of sixteen gallons of water per cycle moves through your clothes to clean them, therefore less water and detergent is used than in agitator washers.
-
Page 3: Important Safety Instructions
Model, Series and Serial numbers are used to identify your new Staber clothes washer. These numbers should always be referred to when consulting the Customer Assistance Center concerning service, parts, or other information you may require. For your convenience and ready reference, enter Model, Series, and Serial numbers below. -
Page 4: Important Grounding Instructions
TWENTY-FIVE YEAR LIMITED WARRANTY FROM DATE OF PURCHASE STABER INDUSTRIES DOES NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion may not apply to you. -
Page 5: Installation
CAUTION: Use great care when loading, unloading or working around clothes basket with top lid raised. DO NOT allow any items to fall between inner and outer tubs. If this should occur DO NOT START WASHER. The item must be removed from the tub or damage to the clothes basket or water system may occur. - Page 6 BENEFITS OF STABER WASHER Washes more clothes per load than a traditional agitator washer and saves on drying time with superior moisture extraction. 2. Gentle wash action ensures less wear and tear on clothes (clothes last longer). 3. Conserves water, energy, and money spent on laundry products. TO WASH CLOTHES, FOLLOW THESE SIMPLE INSTRUCTIONS STEP 1 After raising top outer lid, open access doors to clothes basket.
- Page 7 STEP 1 STEP 4 FOUR THINGS THAT AFFECT THE CLEANLINESS OF YOUR CLOTHES 1. The amount of Agitation: Equipped with a patented inner and outer tub, the Staber washer is designed to increase the agitation rate allowing for minimal use of chemicals, heat and time per wash load. 2.
-
Page 8: Operation
OPERATION CONTROLS Temperature Controls temperature of wash water only. Clothes washer is designed to use cold water for rinses. Water level Controls amount of water entering clothes washer during each fill. Use High setting for all normal loads containing a fully or loosely packed tub. -
Page 9: Maintenance Procedures
MAINTENANCE PROCEDURES REMOVE FRONT PANEL Disconnect the appliance from the power source. Remove the four 5/16 headed screws located at the bottom of the front panel. After the screws have been removed, grasp the panel on both sides and pull forward. Allow the panel to drop free of the top assembly and set aside. - Page 10 DRAIN HOSE PUMP SUMP HOSE REPLACE DRIVE BELT Remove the front panel as directed under "REMOVE FRONT PANEL". Remove belt and inspect pulleys for wear and tightness. Install new belt on pulleys, check belt tension and adjust as necessary. Install front panel on clothes washer as directed under "INSTALL FRONT PANEL"...
- Page 11 14 Reinstall control panel to housing. Insert bottom of control panel into housing first. Then slide the panel into place and secure with six philips head screws. NOTE: Do not over tighten the screws or you will strip the holes and the screws will not hold.
- Page 12 REPLACE PRESSURE SWITCH Disconnect the appliance from the power source. Remove the six philips head screws that hold the control panel to the top. Allow the control panel to slide down, pull the top of the control panel out and lift up. Lay the control panel face down on the top.
-
Page 13: Troubleshooting
PROBLEM Power On light does not illuminate when timer knob is pulled out. Lid locked light does not illuminate during spin cycle. Water does not enter the clothes washer. Water flows continuously. Washer does not agitate. TROUBLESHOOTING CAUSE Clothes washer not plugged in. Electrical outlet does not have AC power. - Page 14 TROUBLESHOOTING PROBLEM Water does not drain from clothes washer. Washer does not spin Washer walks across floor. Washer spins with a full tub of water. Water leaks from washer. Timer does not advance in prewash, wash or rinse cycles. CAUSE Obstruction in sump area of outer tub.
- Page 15 ITEM PART NUMBER DESCRIPTION 813271M Wiring Harness 813226 Motor Controller 813203 Lid Lock 814201 Pump 814237 Water Valve 813215 Pressure Switch 813209 Switch - Temperature 813223 Switch - Water Level 813211 Switch - Program Selector (Wash Cycle) 813267 Timer 813213 Indicator Light - Red 813214 Indicator Light - Green...
- Page 16 PARTS ITEM PART NUMBER 813217 818225 818265 818229 817216 817222 818219 817219 817305 818261 818225 818265 818263 817220 817217 817307 818225 818265 818263 817101 811203 811201 812201 817249 817239M 817105 817253 818201 817111 818227 817265 817267 814201 814213 814217 814215 814221 817135 813225...
- Page 17 PARTS...
- Page 18 Inner Tub Assembly Drive Shaft Assembly Bolt 1/4-20 x 5/8 S.S. Support Shaft Assembly Power Cord Control Panel Screw Panel Overlay - HXW2304, HXW2305 Small White Knob Small Black Knob White Indicator Dial Black Indicator Dial Large White Knob Large Black Knob...
- Page 19 PARTS...
- Page 20 4800 Homer Ohio Lane Groveport, Ohio 43125 614.548.0098 phone www.staber.com Product information and specifications are shown herein as of the time of printing. Staber Industries, Inc. reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligation.
Need help?
Do you have a question about the HXW2304 and is the answer not in the manual?
Questions and answers