Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
EN 2 TPN15.1E LA Revision List 1. Revision List Manual xxxx xxx xxxx.0 10.19 AL 715G7004 Ambilight Board 10.20 AL • First release. 715G6981 Ambilight Board. • Chapter 11: Added styling sheets 11.8 6300 series 40", 11.9 4x00 series 48", 11.10 6300 series 48"...
EN 4 TPN15.1E LA Technical Specs, Diversity, and Connections Connections Rear Connectors Side Connectors HDM I2 HDMI 1 AUDIO IN VGA / DVI S CART (RGB/CVBS) TV ANTENNA SERV .U (Optional) 19790_001.eps Figure 2-1 Connection overview Note: The following connector colour abbreviations are used 6 - PC IN:VGA (acc.
Page 5
Technical Specs, Diversity, and Connections TPN15.1E LA EN 5 - Shield 9 - Cinch: Digital Audio - Out - D1- Data channel BK - Coaxial 0.4 - 0.6V / 75 W - D0+ Data channel - Shield 10 - Service / UART - D0- Data channel - Ground...
Spare Parts the following points: • Route the wire trees correctly and fix them with the For the latest spare part overview, consult your Philips Spare mounted cable clamps. Part web portal. • Check the insulation of the Mains/AC Power lead for external damage.
Page 7
Precautions, Notes, and Abbreviation List TPN15.1E LA EN 7 result in sets which have the same CTN (Commercial Type 6 = play 16 : 9 format, 12 = play 4 : 3 Number; e.g. 28PW9515/12) but which have a different B.O.M. format number.
Page 8
6.5 MHz. L' is Band (VESA standard for communication I, L is all bands except for Band I channel and display). Using E-DDC, LG.Philips LCD (supplier) the video source can read the EDID Loudspeaker information form the display.
Page 9
SOPS Self Oscillating Power Supply Serial Peripheral Interface bus; a 4-wire synchronous serial data link standard S/PDIF Sony Philips Digital InterFace SRAM Static RAM Service Reference Protocol Small Signal Board Spread Spectrum Clocking, used to reduce the effects of EMI...
EN 10 TPN15.1E LA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: 4.7 Assembly/Panel Removal (for 24"PHx5210) 4.1 Cable Dressing 4.8 Set Re-assembly 4.2 Service Positions Notes: 4.3 Assembly/Panel Removal (for 22"/24"Pxx4000) • Figures below can deviate slightly from the actual situation, 4.4 Assembly/Panel Removal (for 32"/39"/40"Pxx4x00) due to the different set executions.
EN 16 TPN15.1E LA Mechanical Instructions XA04 ECN431 CN431 CN8601 CN8602 CN9100 OPTION BOARD (1058) CN438 CN115 ECN701 ECN115 CN701 CN115 CN408 MAIN POWER SUPPLY (1054) (1053) CN601 ECN601 LOUDSPEAKER (1187) KEYBOARD CONTROL (1057) LOUDSPEAKER (1185) IR/LED BOARD (1056) LED BOARD(Logo) (1068) 19792_103.eps Figure 4-12 Cable dressing (55"...
Page 17
Mechanical Instructions TPN15.1E LA EN 17 Assembly/Panel Removal (for 22"/24"Pxx4000) 2. At the indicated areas [2] the cover is securd by clips. Be Instructions below apply to the 24PHK4000/12, but will be very careful with releasing those. similar for other 22"/24"Pxx4000 models. Caution note: At the right bottom of the rear cover is the IR sensor area, be very careful when you releasein the clips otherwise will damage the IR sensor.
Page 18
EN 18 TPN15.1E LA Mechanical Instructions 4.3.2 IR/LED panel 1. Release the connector [5] from the SSB. Caution: be careful, as these are very fragile connectors! 2. Remove fixation screws [6] that secure the speakers, refer 1. Unplug the connector[4] from the IR/LED panel. Figure 4-16 for details.
Page 19
Mechanical Instructions TPN15.1E LA EN 19 4.3.5 Power Supply Unit (PSU) 4. Remove the IR/LED as described earlier. 5. Remove the fixations screws that fix the metal clamps to the front bezel. Take out those clamps. Caution: it is mandatory to remount all different screws at their 6.
Page 20
EN 20 TPN15.1E LA Mechanical Instructions 4.4.2 Rear Cover 1. Remove the fixation screws [2], [3] and [4] that secure the rear cover. Refer to Figure 4-18 Figure 4-19 for details. 2. Gently lift the rear cover from the TV. Make sure that wires Refer to Figure 4-18 Figure 4-19...
Page 21
Mechanical Instructions TPN15.1E LA EN 21 4.4.5 Power Supply Unit (PSU) 4.4.8 LCD Panel Caution: it is mandatory to remount all different screws at their 1. Remove the SSB as described earlier. original position during re-assembly. Failure to do so may result 2.
Page 22
EN 22 TPN15.1E LA Mechanical Instructions 4.5.2 Rear Cover 1. Remove the fixation screws [2] and [3] that secure the rear cover. Refer to Figure 4-22 for details. 2. Gently lift the rear cover from the TV. Make sure that wires Refer to Figure 4-22 for details.
Page 23
Mechanical Instructions TPN15.1E LA EN 23 4.5.5 IR/LED Board 3. Take the speakers out. When defective, replace the both units. Refer to Figure 4-24 Figure 4-25 for details. 1. Remove the fixation screws [1] from the stand bracket, pull 4.5.8 LCD Panel out the assy from the set.
Page 24
EN 24 TPN15.1E LA Mechanical Instructions 19792_104.eps Figure 4-26 Stand removal[1] 19792_105.eps Figure 4-27 Stand removal[2] back to 2015-Oct-30 div. table...
Page 25
Mechanical Instructions TPN15.1E LA EN 25 4.6.2 Rear Cover 1. Remove the fixation screws [1,2,3] that secure the rear cover. 2. Lift the rear cover from the TV. Make sure that wires and Refer to Figure 4-28 for details. flat foils are not damaged while lifting the rear cover from Warning: Disconnect the mains power cord before removing the set.
Page 26
EN 26 TPN15.1E LA Mechanical Instructions 4.6.3 AmbiLight Panel 1. Gently release the clamps and unplug the two connectors [4, 5] that secure the ambilight panels. Release the clips from the FFC connector that connect with the keyboard [6]. Refer to Figure 4-29 for details.
Page 27
Mechanical Instructions TPN15.1E LA EN 27 4.6.6 IR/LED Board Refer to Figure 4-31 for details. 1. Remove the fixation screws [1] from the stand bracket, pull out the assy from the set. Refer to Figure 4-31 for details. 2. Carefully Releas the cover secured by clips, then unplug the connector [2] from the IR/LED board.
Page 28
EN 28 TPN15.1E LA Mechanical Instructions Assembly/Panel Removal (for 24"PHx5210) 1. Remove fixation screws [1] that secure the base assy, pull Instructions below apply to the 24PHH5210/88, but will be out the base assy from the set. Then remove the fixation similar for other 24"PHx5210 models.
Page 29
Mechanical Instructions TPN15.1E LA EN 29 4.7.2 Speakers 2. Remove fixation screws [1] that secure the speakers, refer Figure 4-33 for details. 3. Gently lift the speakers from the TV. Make sure that wires Refer to Figure 4-33 for details. and cables are not damaged while lifting the speakers from 1.
Page 30
EN 30 TPN15.1E LA Mechanical Instructions 4.7.5 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. 1. Gently unplug all connectors from the PSU. 2.
Service Modes and Fault Finding TPN15.1E LA EN 31 5. Service Modes and Fault Finding Index of this chapter: Life Timer 5.1 Test Points During the life time cycle of the TV set, a timer is kept (called 5.2 Service Modes “Op.
Page 32
EN 32 TPN15.1E LA Service Modes and Fault Finding – Automatic user menu time-out (menu switches controls will not have I+ button, but an “INFO” button back/OFF automatically. instead. – Auto Volume levelling (AVL). How to Exit SDM How to Activate SDM •...
Page 33
Service Modes and Fault Finding TPN15.1E LA EN 33 How to Exit SAM • Displaying and or changing Tuner ID information. Use one of the following methods: • Error buffer clearing. • Switch the set to STANDBY by pressing the mains button •...
Page 34
EN 34 TPN15.1E LA Service Modes and Fault Finding Default value Item Item value 22" 24" 32" 39" 40" 48" 55" Description LVDS Driving LVDS Driving LVDS Format VESA JEIDA VESA JEIDA VESA NS 10bit NS 10bit LVDS Format 8bit 8bit 8bit 8bit...
Page 35
Service Modes and Fault Finding TPN15.1E LA EN 35 Stepwise Start-up Standby Soft Mode Command Received, Switch previously in Standby Off(Mains Soft Mode (Power tact Standby Power Plug) switch) Digital Digital background background tasks started tasks completed TV Wakeup commands Received Standby (TV Wakeup...
Page 36
A description on how to upgrade the main 1. ComPair helps to quickly get an understanding on how to software can be found in the DFU or on the Philips website. repair the chassis in a short and effective way.
Service Modes and Fault Finding TPN15.1E LA EN 37 • FUS_clustername_version.zip: Contains the file downloaded which is needed to upgrade the TV main software and the software download application. • NVM_clustername_version.zip: Default NVM content. Must be programmed via ComPair. 5.5.7 How to Copy NVM Data to/from USB When copying data to and from a USB memory stick, the folder “repair”...
Page 38
EN 38 TPN15.1E LA Service Modes and Fault Finding Fault Finding and Repair Tips 5.7.10 Display option code Note: • It is assumed that the components are mounted correctly Attention: In case the SSB is replaced, always check the Panel with correct values and no bad solder joints.
Alignments TPN15.1E LA EN 39 6. Alignments Index of this chapter: In case you have a colour analyser: 6.1 General Alignment Conditions • Measure with a calibrated (phosphor- independent) color 6.2 Hardware Alignments analyser (e.g. Minolta CA-210) in the centre of the screen. 6.3 Software Alignments Consequently, the measurement needs to be done in a 6.4 Option Settings...
Page 40
EN 40 TPN15.1E LA Alignments Table 6-2 White tone default settings Colour temperature Picture mode Screen size Green Blue Colour temperature Cool (11000K) 22PFH4000/88 119 Picture mode Screen size Green Blue 22PFK4000/12 Normal (9000K) 22PFH4000/88 128 22PFT4000/12 22PFK4000/12 22PFT4000/60 22PFT4000/12...
Screen size Green Blue select STORE and press OK on the RC. Warm (6500K) 22PFH4000/88 128 • The new option setting is only active after the TV is 22PFK4000/12 switched “off” / “stand-by” and “on” again with the mains 22PFT4000/12 switch (the NVM is then read again).
Page 42
EN 42 TPN15.1E LA Alignments 6.5.1 Reset of Repaired SSB CTN_ALT BOM# Panel Type Display Code 39PFT4100/12 TPT400LA-J6PE1 SC1X Instruction 39PFT4100/60 TPT400LA-J6PE1 SC1X After NVM replacement, reload MAC address via SAM 39PFH4200/88 TPT400LA-J6PE1 SC1X menu.This ensures the correct MAC address to be available in 39PFK4200/12 TPT400LA-J6PE1 SC1X CSM for future repair actions.
Circuit Descriptions TPN15.1E LA EN 43 7. Circuit Descriptions Index of this chapter: Introduction 7.1 Introduction The TPN15.1E LA is a new chassis launched in Europe in 7.2 Power Supply 2015. The whole range is covered by NT72453 platform. 7.3 DC/DC Converters The major deltas versus its predecessor support DVB-TC;...
Page 44
EN 44 TPN15.1E LA Circuit Descriptions 7.1.3 SSB Cell Layout DC/DC COMMON INTERFACE NT72453 HDMI HDMI AUDIO IN Analog Input SPDIF OUT TUNER Headphone SERVICE CONNECTOR SCART Power Button 19790_200.eps Figure 7-1 SSB layout cells (top view) back to 2015-Oct-30 div.
Page 45
The following displays can be distinguished: specifications! This part is available in the regular market. • CCFL/EEFL backlight: power panel is conventional IPB Consult the Philips Service web portal for the order codes of the • LED backlight: boards. - side-view LED without scanning: PSL power panel - side-view LED with scanning: PSLS power panel Important delta’s with the TPN15.1E LA classis platform are:...
Page 46
EN 46 TPN15.1E LA Circuit Descriptions 7.2.3 Connector overview Table 7-1 Connector overview Connector 22"&24" 4000 32" 4x00 39"&40" 4x00 40" 6300 48" 4x00 48"&50" 6300 Number CN9101 CN8602 CN9101 CN8604 CN9101 CN8601 CN9101 CN8101 CN9101 CN8101 CN9101 CN8101/CN8102 Descriptio to SSB to panel to SSB...
Page 47
Circuit Descriptions TPN15.1E LA EN 47 AUDIO AMP 1.3A AUDIO_12V AD87588 MAIN CHIP BUCK CONVERTER DV11 BUCK CONVERTER NT72453 +5V_STB 1050mA M5723B PWR_12V TPS54428 U701 2866 mA(5V) 285mA U706 1404 mA PWR_ON_2 PWR_ON_2 MAIN CHIP NAND FLASH 11mA K9F1G08U0D NT72453 -SIB0 10mA POWER SWITCH...
Page 48
EN 48 TPN15.1E LA Circuit Descriptions Front-End DVB-S(2) reception Video and Audio Processing - The Front-End for the DVB-S(2) application consist of the NT72453MBG-BA following key components: The NT72453MBG-BA is the main audio and video processor (or System-on-Chip) for this platform. It has the following features: •...
IC Data Sheets TPN15.1E LA EN 49 8. IC Data Sheets This chapter shows the internal block diagrams and pin configurations of ICs that are drawn as “black boxes” in the electrical diagrams (with the exception of “memory” and “logic” ICs).
EN 50 TPN15.1E LA IC Data Sheets Diagram 10-7-1 System Power, B01, M5723B (IC U701) Block diagram Current Sense Current Sense M5723B HDRV HDRV VREF VREF 100mΩ 100mΩ 0.6V 0.6V CONTROL CONTROL LDRV LDRV 80mΩ 80mΩ UVLO UVLO Compensation Compensation Thermal Thermal PGND...
Page 51
IC Data Sheets TPN15.1E LA EN 51 Diagram 10-7-7 NT72453_STBC/FLASH, B07, MX30LF1G08AA (IC U405) Block diagram MX30LF1G08AA High Voltage Circuit Memory Array Control Logic Page Buffer Address Y-DEC R/B# Counter Data IO[7:0] Buffer Pinning information R/B# 19790_300.eps Figure 8-3 Internal block diagram and pin configuration back to 2015-Oct-30 div.
Page 52
EN 52 TPN15.1E LA IC Data Sheets Diagram 10-7-10 Tuner/T2 demod, B10, Si2166-B22 (IC U201) Block diagram Si2166 1.2, 3.3V RESETB DiSEqC DSP & CTRL GPIO SYNCHRO TS_ERR/ S_ADC_IP GPIO_1 QPSK / 8PSK S_ADC_IN ADC (I) VITERBI Satellite TS_SYNC S_ADC_QP QPSK TS_VAL ZIF Tuner...
Page 54
EN 54 TPN15.1E LA IC Data Sheets Diagram 10-7-11 SPK AMP/HP OUT, B11, AD87588 (IC U601) Block diagram AD87588 Pinning information 19790_301.eps Figure 8-6 Internal block diagram and pin configuration back to 2015-Oct-30 div. table...
Page 88
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 88 10.7 B 715G6947 SSB 10-7-1 System Power System Power Backlight ON/OFF Control BL_DIMMING_912 DV33 BL_DIMMING_912 18 AUDIO_12V AUDIO_12V 14 PWR_12V NC/1K PWR_12V 13,17 +5V_STB R738 +5V_STB DC POWER INPUT +5V_SW DV33SB +5V_STB +5V_SW 9,11,13,16,17,18...
Page 114
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 114 10-9-2 IR&LED board layout Layout LED Board (top side) LED1 Layout LED Board (bottom side) 2012-10-26 LED Board 715G5964 layout top/bottom 19790_518.eps back to 2015-Oct-20 div.table...
Page 118
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 118 10-11-2 IR/LED board layout Layout LED Board (top side) Q301 U201 Layout LED Board (bottom side) CN201 2012-10-26 LED Board 715G7055 layout top/bottom 19791_501.eps back to 2015-Oct-20 div.table...
Page 120
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 120 10-12-2 IR/LED board layout Layout LED Board (top side) CN201 C203 R226 R203 R223 U202 R212 R204 R211 Q201 R202 Q202 R222 R216 R224 R217 U201 U203 LED204 LED202 LED201 Layout LED Board (bottom side) 2014-11-04...
Page 121
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 121 10.13 E 715G6316 Keyboard control panel 10-13-1 Direction switch Key function Resistance Voltage Center 2-5 short Menu Right 1-5 short 0.5V Left 4-5 short 0.81V Down 3-5 short VOL- 1.65V CN01 6-5 short VOL+ 2.27V...
Page 122
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 122 10-13-2 Key board layout Layout Keyboard control panel (top side) SW01 Layout Keyboard control panel (bottom side) 2013-09-17 Keyboard control panel 715G6316 layout top/bottom 19610_546.eps back to 2015-Oct-20 div.table...
Page 123
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 123 10.14 E 715G7088 Keyboard control panel 10-14-1 CN01 CN01 KEY1 CONN CONN 0.1uF 50V 0.1uF 50V TACT SW 6P TACT SW 6P SW01 SW01 Right Center Down Left 2014-05-28 Keyboard control panel 715G7088 19791_502.eps back to...
Page 124
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 124 10-14-2 Key board layout Layout Keyboard control panel (top side) SW01 Layout Keyboard control panel (bottom side) 2014-06-06 Keyboard control panel 715G7088 layout top/bottom 19791_503.eps back to 2015-Oct-20 div.table...
Page 125
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 125 10.15 E 715G7188 Keyboard control panel 10-15-1 CONN TO SSB JOYSTICK Direction switch Key function Resistance Voltage Center 2-5 short Menu CN01 Right 1-5 short 0.5V KEY 1 AMBI_SPI_CLK Left 4-5 short 0.81V AMBI_SPI_MOSI 0.1uF 50V...
Page 126
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 126 10-15-2 Key board layout Layout Keyboard control panel (top side) Layout Keyboard control panel (bottom side) SW01 SW11 2014-11-06 Keyboard control panel 715G7118 layout top/bottom 19792_511.eps back to 2015-Oct-20 div.table...
Page 127
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 127 10.16 ALC 715G7046 LED Board( LOGO) 10-16-1 Lited LED Lited LED 3V3SB 3V3SB LED301 LED302 R301 R303 2R2 1/16W 5% 2R2 1/16W 5% R302 Q301 CN301 1K 1/16W 5% BC847C LOGO 3V3SB 2014-10-06 Lited LED...
Page 128
Circuit Diagrams and PWB Layouts TPN15.1E LA EN 128 10-16-2 LED LOGO Board layout top/buttom Layout LED LOGO Board (top side) CN301 Q301 Layout (bottom side) LED LOGO Board 2014-11-01 LED LOGO Board 715G7046 layout top/bottom 19792 513.eps back to 2015-Oct-20 div.table...
Need help?
Do you have a question about the 22PFH4000/88 and is the answer not in the manual?
Questions and answers