Samsung DW80R9950 Series Installation Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Dishwasher
  5. DW80R9950 Series
  6. Installation manual

Samsung DW80R9950 Series Installation Manual

Hide thumbs Also See for DW80R9950 Series:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Dishwasher
Installation manual
DW80R9950* Series
DW9900R_DD68-00208B-00_EN.indd 1
12/29/2018 1:57:35 PM

Advertisement

Table of Contents
loading

Related Manuals for Samsung DW80R9950 Series

Summary of Contents for Samsung DW80R9950 Series

  • Page 1 Dishwasher Installation manual DW80R9950* Series DW9900R_DD68-00208B-00_EN.indd 1 12/29/2018 1:57:35 PM...

  • Page 2: Installation

    Contents Safety instructions Important safety instructions Before using your dishwasher Installation Product dimensions Cabinet dimensions Specifications Scan the QR code* to view our helpful installation videos. * Requires reader to be installed on your smartphone. English DW9900R_DD68-00208B-00_EN.indd 2 12/29/2018 1:57:35 PM...

  • Page 3: Important Safety Instructions

    It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher. Samsung is not liable for damages resulting from improper use.

  • Page 4: California Proposition 65 Warning

    Safety instructions California Proposition 65 Warning WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov Read all instructions before using the appliance. Install and store the dishwasher inside, away from exposure to weather. CAUTION • Do not install the dishwasher near electrical components. Keep the dishwasher away from open flames.

  • Page 5: Before Using Your Dishwasher

    Make sure to use a new water supply line. Old lines are susceptible to breakage because they become hardened and may cause property damage due to a water leakage. The dishwasher must be connected to a hot water supply with a temperature between 120 °F (49 °C) ~ 149 °F (65 °C).

  • Page 6: Parts Required

    Installation Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you are not at risk of injury when washing dishes. STEP 1 Check the parts and tools Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher.
  • Page 7 Not provided Power cable Twist on wire Strain relief Electrical tape & connector Standard duct tape Hot water supply 90° Fitting ( ") Tube fittings Hose clamp line Air gap Rubber connector NOTE For the hot water supply line – We strongly recommend using "...

  • Page 8: Tools Required

    Installation Tools required Electric drill Safety glasses Gloves Flashlight Adjustable wrench Wire stripper Pliers Nipper Tape measure Pencil Phillips screwdriver Flat screwdriver Tubing cutter Cutting knife Hole saw Level Torx t20 Hex L-wrench English DW9900R_DD68-00208B-00_EN.indd 8 12/29/2018 1:57:40 PM...
  • Page 9 NOTE New installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher.
  • Page 10 Installation If this is a new installation, follow these steps: 1. Using a 2 inch hole saw, cut a hole into the side of the cabinet that holds the sink as shown in Figure 1-1 below. 2. If the base inside the sink cabinet is raised above the kitchen floor and is higher than the connections on the dishwasher, make a hole in the base inside the cabinet and in the cabinet side as shown in Figure 1-2.

  • Page 11: Product Dimensions

    Product dimensions Front view Rear view Junction box " (605 mm) Side view " (60 mm) " (520 mm) 25" (636 mm) You must arrange the water supply line, power cable and drain hose in the space behind the dishwasher. English 11 DW9900R_DD68-00208B-00_EN.indd 11 12/29/2018 1:57:41 PM...

  • Page 12: Cabinet Dimensions

    Installation Cabinet dimensions NOTE This dishwasher is designed to be enclosed on the top and on both sides by a standard 24" (610 mm) minimum residential kitchen cabinet unit. The installation cabinet must be clean and free of any obstructions. 24"...

  • Page 13: Step 3 Check Water Supply Requirements And Cautions

    STEP 3 Check water supply requirements and cautions • The hot water supply line pressure must be between 20 ~ 120 psi (140 ~ 830 kPa). • Adjust the water heater to deliver water between 120 °F (49 °C) ~ 149 °F (65 °C). - The dishwasher must be connected to a hot water supply between 120 °F (49 °C) ~ 149 °F (65 °C).
  • Page 14 Installation STEP 4 Check the electrical requirements and cautions The electrical requirements for the dishwasher are as follows: • In the United States, install in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/ Provincial and Municipal codes and/or local codes.

  • Page 15: Step 5 Unpacking And Inspecting The Dishwasher

    STEP 5 Unpacking and inspecting the dishwasher Unpack the dishwasher in an open area free of obstruction both around the packaging and overhead. We recommend that you retain all of the packing materials until the dishwasher is fully installed and operational to ensure you have removed all the product’s components from the packing materials prior to disposal.
  • Page 16 Installation Inspecting Mechanical 1. Check the plastic base assembly to ensure that it is intact 2. Check the dishwasher’s feet to ensure they are in place and can be adjusted so you can level and secure the dishwasher. 3. Check all the visible components on the bottom of the dishwasher to ensure they are intact and secure.

  • Page 17: Step 6 Preparing The Dishwasher

    STEP 6 Preparing the dishwasher 1. Attach the protective sticker (A). - To prevent damage, put the protective sticker on the bottom of the counter top as shown in the picture. NOTE • Before putting the protective sticker, clean the counter top as shown in the picture. •...
  • Page 18 Installation 3. Use the provided nut connector to connect the water hose to the dishwasher. Follow these steps: 01 Disconnect the 90° fitting (A) from the hose (B). 02 Remove the seal (C) and the nut (D) from the 90° fitting. 03 From the provided nut connector, separate the seal (E) and the nut (F), and then assemble them to the 90°...
  • Page 19 Figure 4 Junction box Strain relief 90° fitting CAUTION Do not overtighten the 90° Fitting. (Below 280 lb·in (31.6 N·m)) Doing so may damage the water inlet valve and cause a water leak. English 19 DW9900R_DD68-00208B-00_EN.indd 19 12/29/2018 1:57:43 PM...
  • Page 20 Installation STEP 7 Placing the dishwasher and connecting the hot water supply line 1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (See STEP 8, Leveling the Dishwasher.) 2.
  • Page 21 Figure 5 Side gasket Junction box Side gasket 1 inch Drain hose Hot Water Supply Line Power cable Inlet valve built-in hook Hot Water Supply Line Elbow ( " (9.5 mm)) CAUTION Do not overtighten the 90° Fitting. (Below 280 lb·in (31.6 N·m)) Doing so may damage the water inlet valve and cause a water leak.

  • Page 22: Step 8 Leveling The Dishwasher

    Installation STEP 8 Leveling the dishwasher 1. Open the door and place the level against the top of the tub on the inside and check if the the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level.
  • Page 23 NOTE • If the leveling legs are rotated to the left (clockwise), they are loosened and the front of the dishwasher is raised. If they are rotated to the right (counter clockwise), they are tightened and the front of the dishwasher is lowered. •...

  • Page 24: Step 9 Securing The Dishwasher

    Installation STEP 9 Securing the dishwasher You must fix the dishwasher to the countertop or cabinet side walls for additional stability and safety. To the countertop If the countertop is made of wood or the material will not be damaged by drilling, follow this.
  • Page 25 To the sides If the countertop is made of granite, marble, or any other material that can be damaged by drilling, follow this. 1. Put a large towel into the bottom of the dishwasher(covering the filter) to prevent wood shavings or a dropped screw from falling into the sump.
  • Page 26 Installation Good 22" (560 mm) 22" (560 mm) Do not to exceed 22" (560 mm) distance between the Caps CAUTION Make sure the tub is not distorted by pressure from the screws. If the tub is distorted, loosen the screws a little. Replace the plastic caps. Use the paper ruler to measure the specified distance on A and B.
  • Page 27 STEP 10 Securing 1. Check the parts on the sink to which the drain hose will be connected. 2. There are several ways to insert the drain hose into the drain hose connector of the sink, as shown in the following figures. You must connect the drain hose in accordance with the water pipe installation regulations in your region.
  • Page 28 Installation 4. Slide a hose clamp over the end of the drain hose. Attach the drain hose to the sink connector, slide the hose clamp to the end of the hose, and then tighten the hose clamp. NOTE You must use a hose clamp. Failure to do so may cause water leakage. 5.
  • Page 29 Figure 9 1 in. (25 mm) (16 mm) (22 mm) If necessary, cut off the dotted line of the drain hose to fit the size. Figure 10 To prevent backflow for models without the air gap, secure the drain hose to the Dishwasher Sink side wall of the kitchen cabinet using cable...

  • Page 30: Step 11 Wiring Connections

    Installation STEP 11 Wiring connections 1. Before connecting the power cable to the dishwasher, make sure the circuit breaker is off. 2. In the junction box located at the front bottom right of the dishwasher, find the three power wires from the dishwasher including the grounding line. 3.
  • Page 31 Figure 12 WARNING • Electrical Shock Hazard To avoid electrical shock, do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de-energized.

  • Page 32: Step 12 Completing The Installation

    Installation STEP 12 Completing the installation 1. Open the door and remove all foam, paper packaging, and unnecessary parts. 2. Turn on the circuit breaker you turned off before you began the installation. 3. Open the water supply valve to supply water to the dishwasher. 4.
  • Page 33 Kick plate Gasket CAUTION Make sure the kick plate does not interfere with the dishwasher's door opening and closing. English 33 DW9900R_DD68-00208B-00_EN.indd 33 12/29/2018 1:57:47 PM...

  • Page 34: Specifications

    Specifications Power supply 120 V, 15 A, 60 Hz AC Water pressure 20 ~ 120 psi (140 ~ 830 kPa) Dimensions x 25 x 33 (Width×Depth×Height) (605 x 636 x 860 mm) 120 °F (49 °C) Minimum inlet water temperature NOTE Specifications are subject to change without notice for quality improvement purposes.

Table of Contents