Emco -star Instruction Book page 35

EMCO-REX SURFACE PLANER
T chnical data:
e
Cutt r h
e
Cutting circule diameter of kniv
Spe d 3000 r • P · m ·
e
Cutting sp
Sp d 37
ee
Cutting sp
Planing width 8
Max. d
e
L ngth of tabl
e
Th surfac
e
1
d pth of cut
a=
e
The d pth of cut to which th
e
CORRECT OPERATIO N OF SURFACE PLANER
quir
The r
e
(Sk tch 2).
e
On av rag
e
this setting th
For planing, th
push d against th
e
this nd should b
e
push th
e
The concav
conv x sid
e
To plan
e
Th e board is then held with the p laned face p ressed a g ainst rhe fence cJ11cl ;,. ;, 71,ch
11
dia. with 3 kniv
ad 2 27 /32
e
} as an attachm
d 39 1/4 ft/s c
ee e
oo
r.p.m.
} as an indep
d 47 ft/s c
ee e
11
pth of cut 7 / 64
11
26 3/4"
e
plan r is us d for planing boards and batt
e e e
workpi c
e
'
Sk tch 5
e
machine is s
e
d d pth of cut is s t by raising or low
e e e
, it will be found advisabl
e
plan d surfac will b
e e e
workpi c is laid on th
e e e
cutt r h ad. As soon as th
e e e
pr ss d down onto th
e e e
workpi c against th cutt
e e e
sid of a board is always plan
e e
on the tabl , it could not b
e e
an edge (narrow sid of board), th
e
· - 33 -
11
s l 3/16 x l/8
e
s 2 2 9 / 32
11
e
nt
e
nd nt machin
e e
e
cutting circl
e
t is shown on a scal
e
ring the front table by m
e
to s t th depth of cut to 1/32
e e e
r than at 7 / 64
much smooth
e e
front tabl , pr
e e
front of th
e
back tabl with on
e e
r head.
e
d (se Sk tch 6). If th
e e e
h ld l vel whil
e e e
f nce is fitted squar
e
e
x 8 1/4
11
11
e
ns, for b v lling, and for jointing.
e e e
Front table (infe
Back tabl (outf
e
Cutting circl
e
Workpi c
e e
D pth of cut
e
Th kniv s ar
e e e
xactly flush with th
e
(Sk tch 5, No. 2).
e
If, as shown in Sketch 5, th
table is s t lower than this by an
e
11
1
amount a a strip of thickn
1,
will b plan d off the workpi
e e
Th h ight of th
e e
M 60. 20-04 is adjust
th knob M 60. 20. 3 (Sk
e
M 60.20-22 at the sid
e
ans of the knob M 60.20.3
e
(maximum 7 / 64
11
•
11
ss d down with both hands, and slowly
e e
workpi c has pass
e e e
hand whil th
e e e
board wer
e
it is f d over th kniv
e e e
to th tab I
e e
l
d tabl )
e e
2
d tabl )
ee e
3
4
a
s t so that th y ar
e e e
back tabl
e e
front
e
11 11
ss 0
e
ce.
e
front table
e
d by turning
e
tch 2).
e
(Sketch 2).
e
11
sinc at
)
e
d the cutt ad,
r h
e
e e
other continues to
laid down with its
e
s.
e
surface.
e
r! ,,v:1-r.. . � ·
,:;