Table of Contents
Advertisement
Quick Links
Habasit AG
Postfach, CH-4153 Reinach-Basel
Phone
++41 61 715 15 15
Fax
++41 61 715 15 55
Edition:
01/0206
Flexproof-Cutter AF-61/8x30
The AF-61/8x30 is a preparing device (die-cutting tool) for 8x30 mm
Flexproof finger geometry. It is designed mainly for Habasit machine tapes
and belts up to 3 mm thickness.
The AF-61/8x30 has a movable cutting head with two blades. It can be
positioned by a pin in steps of 8 mm, ensuring the required accuracy. The
fingers are thus cut manually step by step by means of a lever.
The AF-61/8x30 is designed and suitable for occasional on-site preparation of
Hamid tapes and belts.
Operating Instructions
4123
Page 1 of 14
Subject to alteration
4123INS.FAB-en0306ITA
Advertisement
Table of Contents
Related Manuals for Habasit AF-61/8x30
Summary of Contents for Habasit AF-61/8x30
- Page 1 Flexproof finger geometry. It is designed mainly for Habasit machine tapes and belts up to 3 mm thickness. The AF-61/8x30 has a movable cutting head with two blades. It can be positioned by a pin in steps of 8 mm, ensuring the required accuracy. The fingers are thus cut manually step by step by means of a lever.
-
Page 2: Table Of Contents
Flexproof-Cutter AF-61/8x30 Operating instructions 4123 Page of 14 Edition: 01/0206 Subject to alterations Table of contents: General information ..........................3 Application............................. 3 Important safety terms .......................... 3 Scope of supply............................. 4 Ordering of accessories/spare parts..................... 4 Warranty..............................4 Technical advice ........................... 4 Mode of operation .......................... -
Page 3: General Information
Habasit spindle tapes and Hamid machine tapes using the Flexproof procedure. The belts/tapes can be up to 60 mm/2.36 in. width and 3 mm/0.12 in. thickness. It is suitable for Habasit standard finger geometry with the pitch of 8 x 30 mm. Die-cutting is done in manual strokes‚ resulting in the most precise finger cut and therefore optimum joint strength. -
Page 4: Scope Of Supply
Please specify the ordered parts clearly, referring to the part numbers and if necessary to the illustrations in this manual. WARNING The use of foreign parts not meeting Habasit specifications is not admissible. Habasit declines all responsibility for the consequences if non-Habasit parts are used. -
Page 5: Mode Of Operation
The max. belt/tape thickness that can be cut is 3 mm/0.12 in. and 60 mm/2.4 in. is the max. possible belt/tape width. Initial start-up For safe operation, place the Flexproof-Cutter AF-61/8x30 on a solid workbench or table. If it is used only stationary it is recommended to fix the stand. Screw the lever (16) to the pressing structure (15). -
Page 6: Cutting Of Belt/Tape Ends
Flexproof-Cutter AF-61/8x30 Operating instructions 4123 Page of 14 Edition: 01/0206 Subject to alterations Cutting of belt/tape ends Process: Flexproof guidelines and individual product datasheets Flexproof cutting of the belt/tape Pull the indexing plunger (21) and move the cutting head slider (11) to the middle of the cutting pad (2). -
Page 7: Continuing Flexproof Cutting
Flexproof-Cutter AF-61/8x30 Operating instructions 4123 Page of 14 Edition: 01/0206 Subject to alterations Continuing Flexproof cutting The belt/tape end has already fingers cut in correct shape. From last cutting operation, the mark B is visible. This mark is used as a reference for the following measuring and cutting procedure according to 4.2 (see illustration 2). -
Page 8: Service
Flexproof-Cutter AF-61/8x30 Operating instructions 4123 Page of 14 Edition: 01/0206 Subject to alterations Service Preventive Maintenance Keep the cutting pad (2) clean at all times. Clean it regularly and remove material residues. Check the cutting blades (26) periodically for their sharpness and replace with the correct type if necessary. -
Page 9: Technical Data
Flexproof-Cutter AF-61/8x30 Operating instructions 4123 Page of 14 Edition: 01/0206 Subject to alterations Technical data Max. belt/tape width [mm] [in.] Max. belt/tape thickness [mm] [in.] 0.12 Dimensions without lever (L x W x H) [mm] [in.] 180 x 150 x 170 7 x 5.9 x 6.7... -
Page 10: Drawings
Flexproof-Cutter AF-61/8x30 Operating instructions 4123 Page of 14 Edition: 01/0206 Subject to alterations Drawings 4123INS.FAB-en0306ITA... -
Page 11: Spare Parts
Flexproof-Cutter AF-61/8x30 Operating instructions 4123 Page of 14 Edition: 01/0206 Subject to alterations Spare parts POSITION CODE DESCRIPTION H08D003076 Base plate H08D003077 Cutting pad H08D003078 Front belt clamp H08D003079 Rear belt clamp H08D003080 Side support H08D003081 Side support H08D003082 Front locking plate... - Page 12 Checklist preventive maintenance Operating instructions 4123 Flexproof-Cutter AF-61/8x30 Appendix Page 12 of 14 Edition: 01/0206 Subject to alterations Responsible persons: Machine Operator Maintenance Technician Work to be carried out Performance Spares number (see operating instructions for further information and reference numbers)
- Page 13 Report sheet preventive maintenance Operating instructions 4123 Flexproof-Cutter AF-61/8x30 Appendix Page 13 of 14 Edition: 01/0206 Subject to alterations Machine type: Machine no.: Date of first placing in operation: Actions to be performed – see checklist Next Performed Next Performed...
- Page 14 Subject to alterations Product liability, application considerations If the proper selection and application of Habasit products are not recommended by an authorized Habasit sales specialist, the selection and application of Habasit products, including the related area of product safety, are the responsibility of the customer.
Need help?
Do you have a question about the AF-61/8x30 and is the answer not in the manual?
Questions and answers