Fmart YZ-X1 Instruction Manual
  1. Manuals
  2. Brands
  3. Fmart Manuals
  4. Vacuum Cleaner
  5. YZ-X1
  6. Instruction manual

Fmart YZ-X1 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the YZ-X1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Fmart YZ-X1

  • Page 1 INSTRUCTION MANUAL...

  • Page 2: Table Of Contents

    Table of Contents 1 Important Safety Instructions...............1 2 Product Components...................2 ..............2 2.1 The main machine and accessories ..................3 2.2 The main machine ..................3 2.3 Charging station ....................4 2.4 Dustbin ....................4 2.5 Water tank ....................4 2.6 Side brush ..................4 2.7 Remote control 3 Product Operations..................6 ..................6 3.1 Quick start guide...

  • Page 3: Important Safety Instructions

    1 Important Safety Instructions Please read the following safety instructions before using this product to avoid damage. Warning! Violation of safety instructions may cause severe personal casualty and property loss. Do not put weight on the power cord or Always use the original charger with this product, otherwise may cause bend the power cord, otherwise may FDXVH HOHFWULF VKRFN RU ¿UH...

  • Page 4: Product Components

    2 Product Components 2.1 The main machine and accessories Name Quantity Main machine Charging station Remote control Adapter Cleaning brush Insturction manual Side brush 2pcs Water tank Attention: Please take actual product shall prevail on the basis of not less than the above accessories.

  • Page 5: The Main Machine

    2 Product Components 2.2 Main machine 1. Signal receiving 6. Charging poles 11.Dustbin cover button sensor 7. Battery cover 12.Charging socket 2. Clean button 8. Stair detection 13. Side brush 3. Bumper sensor 14. Drving wheel 4. Panel 9. Main brush 5.

  • Page 6: Dustbin

    2 Product Components 2.4 Dustbin 3.Dusbin upper cover 4. Dusbin botton cover 2.5 Water tank 1. Water tank button 2. Water inlet cap 3. Air valves 4. Mop 2.6 Side brush Please install the side brush according to the color of the socket of the side brush.
  • Page 7 2 Product Components Press direction button to adjust the robot moving direction. Press this button for 3 seconds to start time VHWWLQJ SUHVV DJDLQ WR FRQ¿UP WLPH VHWWLQJ The main machine will start the distribution net work if press the button for a long time which above 3 seconds.

  • Page 8: Product Operations

    3 Product operations 3.1 Quick start guide 1.Place charge Place charger, connect the adapter and power, and the power light on the charger will stay lit. Position the charger against the wall, and remove all obstacles about 1 or 2 meters ahead of the charger. 2.

  • Page 9: Start/Pause/Standby Mode

    3 Product operations Attention: 1 When charging, make sure the power switch is on. 2 using the charger stand will interrupt the charging and start the cleaning, so please do not make this operation when using thedirect charge.  &KDUJLQJ WKH PDFKLQH  KRXUV IRU WKH ¿UVW WLPH 4 When charging, the cleaning button blinks, and when fully charged, the cleaning button stops blinking, and lit permanently.

  • Page 10: Cleaning Mode

    3 Product operations  /RQJ SUHVV WKH FORFN EXWWRQ LQ WKH UHPRWH FRQWUROOHU IRU  VHFRQGV DQG VHW D VSHFL¿F WLPH according to “up, down, left and right” direction button. 2 Press the clock button once again to save the setting. 2.Set the pre-scheduled cleaning time 1 Point the remote controller at the machine (the machine is in standby status).

  • Page 11: Water Tank And Mop Operation

    3 Product operations 2.Spot cleaning Place machine in clean area, press the remote button on the machine to start with the placement point spiral sweep. 3.Edge cleaning Press button on remote control to start edge cleaning mode, the robot will start edge cleaning.
  • Page 12 3 Product operations 5 Put the tank into the machine, start the machine, and water enters into the mop through wool column, water stopped dripping out of the tank when the machine stops. Pour water out if the machine stops working for a long time. 2 Installation of water tank jacks.

  • Page 13: Product Maintenances

    4 Product Maintenances 4.1 Cleaning of side brush Side brush can be removed and clean by water. Please dry them completely before second use. If side brushes damaged, please replace them. Attention: When replace side brush, please pay attention to the L and R position and color. 1 Press PUSH button on dustbin, remove the dustbin.

  • Page 14: Cleaning Of Sensors And Charging Poles

    4 Product Maintenances 4.3 Cleaning of sensors and charging poles 1 Clean sensors and charging poles on robot bottom by using soft cloth. 2 Clean charging poles on charging station by using soft cloth. 4.4 Cleaning of main brush 1 Press the locker, open main brush cover. after cleaning.

  • Page 15: Water Tank Maintenance

    4 Product Maintenances 4.5 Water tank maintenance The mop needs to be cleaned on time, the mop is removed from the water tank and cleaned. Note: If the water tank is not used for a long time, please pour out the water. 4.6 Battery replacement 1 Open the battery cover by using a screw driver.

  • Page 16: Resume To Default Setting

    5 Resume to Default Setting If the machine has some software system problems during the using ,it can be triggered by the 1 Hold down the host front collision left sensor when the produce is in shutdown state. 2 While hold down the host front collision left sensor ,open the power switch on the bottom ,the host machine lights starts blinking.

  • Page 17: Troubles Shooting

    6 Trouble shooting Problems Solution The robot keeps 1 Avoid working in high light intensity environments. moving backwards 2 Avoid working on deep dark carpets. 3 Clean the stair detection sensors by using a soft cloth. 4 Check the bumper and clean. The robot do not work 1 Turn on the power switch button.

  • Page 18: Product Parameters

    7 Product Parameters Size 320*320*85mm Net Weight 2.6kg Working voltage 14.8V Input voltage Input current 1.0A Dustbin capacity 400mL One time charging time 4-6h One time cleaning time 90-120min...
  • Page 19 8 F C C Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

Table of Contents