Advertisement
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: predator@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2015 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
WARNING! Do not start or operate any internal
combustion engine inside or near Shed.
Vehicle not included.
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
19h
Advertisement
Related Manuals for Harbor Freight Tools CoverPro
Summary of Contents for Harbor Freight Tools CoverPro
- Page 1 No portion of this manual or any artwork contained herein may be reproduced in Failure to do so can result in serious injury. any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing SAVE THIS MANUAL.
-
Page 2: Table Of Contents
Table of Contents Safety ............3 Maintenance ..........13 Specifications ..........4 Parts List and Diagram ......14 Assembly ............ 5 Warranty ............ 16 WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. -
Page 3: Safety
Do not use grill, heater, These carry important safety information. or ignition sources inside or near cover. If unreadable or missing, contact Harbor Freight Tools for a replacement. SAVE THESE INSTRuCTIONS. Item 62859 Item 62859 For technical questions, please call 1-888-866-5797. -
Page 4: Specifications
Specifications Overall Dimensions 10′ W x 17′ L x 9′ 2" H Center Height 9′ 2" Side Height 6′ 5" Pole Tubing Diameter 1.27" Assembly Read the ENTIRE IMpORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram on page 14. - Page 5 Frame Assembly Overview 11-2 11-1 11-3 Item 62859 For technical questions, please call 1-888-866-5797. Page 5...
- Page 6 Roof Frame Assembly Note: Much of this product’s assembly is done using slip fit construction. Make sure all parts seat completely and securely. A rubber mallet (sold separately) can be used to gently tap parts in place to ensure a tight fit. Figure A: Roof Assembly Overview 1.
- Page 7 3. Assemble a roof side rail using a 3-Way Side Connector B (A2), three Rails (4) with 4-Way Side Connectors (B1) between them, and then a 3-Way Side Connector A (A1) on the other end (see Figure D). The Rails connect to the straight ends of the Connectors, and the curved ends of all Connectors must face up angled the same direction, as shown.
- Page 8 Stud Installation 1. With assistance, raise one side of the roof assembly. 2. Install the Center Studs (1) into the 4-Way Side Connectors (B1), and the Corner Studs (2) into the 3-Way Side Connectors A/B (A1, A2) with the Corner Legs (6) facing inward. Figure G: Stud Installation 3.
- Page 9 Anchoring Frame TO pREVENT SERIOuS INJuRY: Contact local utility companies to ensure that the installation area is free of pipes, cables, and other hazards BEFORE installing anchors or choosing installation area. 1. Position the frame in the desired installation location. 3.
- Page 10 Securing Ratchet Tie-Downs Note: Use these instructions in the pages that follow. 3. Lift and lower the Ratchet’s handle to wind and tighten the strap onto the spindle. 1. Thread the strap through the Ratchet’s (8) spindle as far as it will go. Figure M: Tightening Ratchet NOTICE: Excessive tightening will damage Figure K: Threading Strap through Spindle...
- Page 11 Door and Back Cover Installation 1. Position the Door Cover (16) near where you want 2. Disconnect the Rail (4) from the the front of the Portable Garage, and turn it so 3-Way Ridge Connector (A), and place the that the zipper faces the outside of the Portable gap at the top center of the Door Cover Garage, and the warning tag faces inside.
- Page 12 Roof Cover Installation Note: Door and Back Covers (16, 17) not shown on 5. Make sure the Bottom Rails are level and horizontal. illustrations to provide a clear view of installation. 1. Lay the Roof Cover (15) on the ground next to the frame.
-
Page 13: Maintenance
Maintenance procedures not specifically explained in this manual must be performed only by a qualified technician. TO pREVENT SERIOuS INJuRY FROM pRODuCT FAILuRE: Do not use damaged products. If damage is noted, have the problem corrected before further use. MONTHLY, inspect the general condition of the Portable Garage. Check for: •... -
Page 14: Parts List And Diagram
parts List and Diagram parts List Note: Individual part illustrations not to scale. part Description Illustration part Description Illustration 3-Way Ridge 3-Way End Connector Rail Clamp 3-Way Side 4-Way Center Connector A Rail Clamp 3-Way Side 11-1 Anchor Connector B 4-Way Ridge 11-2 Cable - 1′... - Page 15 Assembly Diagram 11-1 11-2 11-3 11-1 11-3 11-1 11-1 11-3 11-2 11-2 11-2 11-3 Item 62859 For technical questions, please call 1-888-866-5797. Page 15...
-
Page 16: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
Need help?
Do you have a question about the CoverPro and is the answer not in the manual?
Questions and answers
Can I replace the ratchet tie downs for my cover pro carport
Yes, you can replace the ratchet tie-downs for the Harbor Freight Tools CoverPro carport. The manual specifies using ratchet tie-downs (Item 8) to secure the cover to the frame. If you choose replacements, ensure they have similar strength and durability for proper stability.
This answer is automatically generated