Related Manuals for Bissell CLEANALONG 48K2
Summary of Contents for Bissell CLEANALONG 48K2
- Page 1 CleanAlong U S E R ’ S G U I D E 4 8 K 2 S E R I E S ™ Safety Instructions Product View Assembly Operations Maintenance and Care 10-12 Troubleshooting Consumer Services Replacement Parts Warranty...
- Page 2 Your BISSELL canister vacuum is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
-
Page 3: Important Safety Instructions
MPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: REaD all InStRUctIonS bEfoRE USInG yoUR canIStER VacUUM. Always connect to a polarized outlet (left slot is wider than right). Unplug from outlet when not in use and before conducting maintenance. -
Page 4: Product View
roduct view Flex Hose Swivel Hose Power Button Bag Change Indicator Post-Motor HEPA Media Filter BareFloor Tool Floor Brush w w w . b i s s e l l . c a Variable Suction Power Control Brush Roll On/Off Handle Telescoping Extension Wand Automatic... -
Page 5: A Ssembling Your Vacuum
ssembling your vacuum Connect swivel hose by squeezing both locking buttons and inserting it into the suction opening on the canister. Once the swivel hose is inserted in the suction opening, release the locking buttons. Plug the cord from the hose into the slot on the lower left front of canister. Connect and plug-in telescoping extension wand to the handle end of the flex hose. Connect the powerhead onto the telescoping extension wand. Attach the tool holder to the telescoping extension wand and insert the tools into the holder. To extend the telescopic tube, push the black release button and then pull the tube to the desired length. notE: Shorten length of telescopic tube for storage. To store the barefloor tool, insert the storage clip into the storage slot on the rear of the vacuum or on the back of the unit when in an upright position. w w w . b i s s e l l . c a WaRnInG: Plastic film can be dangerous. -
Page 6: Special Tools
Special tools your bISSEll cleanalong is not only a powerful carpet and rug vacuum cleaner, it’s also a versatile bare floor vacuum cleaner and above floor vacuum cleaner when you select one of the special tools. Powerhead: The CleanAlong comes with the powerhead for your regular use. The powerhead has many features, including: 1. A motorized, rotating brush that can be... -
Page 7: Power Cord
perations Power cord the power cord is located at the rear of the vacuum. Gently pull out the power cord, watching for the yellow line. Stop pulling the power cord once the yellow line is visible. there is also a red line, which indicates the end of the usable cord. -
Page 8: Handle Position
High filtration dust bag the bISSEll cleanalong features a non-woven, high filtration dust bag that captures more fine dust than traditional paper dust bags, giving off less dust emissions. It also holds more fine dust particles, giving you longer lasting suction power. -
Page 9: Bag Change Indicator
perations Bag change indicator the bag change indicator is located between the power button and the automatic cord rewind button. If the bag change indicator turns orange while you are vacuuming, the dust bag needs to be replaced. the dust bag may appear to be full or only partially full depending upon the type of debris picked up. -
Page 10: Cleaning The Pre-Motor Filter
aintenance and care Cleaning the pre-motor filter the pre-motor filter protects the motor from dirt and dust particles. 1. Unplug the vacuum from electrical outlet. 2. Disconnect hose 3. Open the dust bag compartment by lifting up on the latch on the door at the front of the vacuum. Lift out the dust bag holder and dust bag. 4. Remove the filter frame from the filter holder by grasping the lip of the frame and pulling 5. Remove the filter from the filter frame and clean by hand washing in warm water. A mild detergent can be used if desired. Allow the filter to air dry thoroughly before replacing. 6. Place the filter back into the filter frame and replace back into the filter holder. notE: the filter frame should be placed so the protective frame is visible. -
Page 11: Maintenance And Care
aintenance and care Replacing the post-motor HEPA media filter the post-motor HEPa media filter assists in the filtration process to return clean air to the room. 1. Unplug the vacuum from electrical outlet. 2. Remove the filter door (located on the rear of the vacuum) by pulling up on the filter door latch. 3. Remove the post-motor HEPA media filter by grasping the lip of the filter frame and pulling up. 4. Replace the post-motor HEPA media filter with a new filter. notE: the post-motor filter is a white, pleated HEPa media filter. -
Page 12: Replacing The Drive Belt
aintenance and care Cleaning the motorized powerhead the brush can usually be cleaned without removal from the vacuum. If there is an excessive amount of hair and debris, however, it is best to remove the brush. 1. Unplug the vacuum. 2. Lay the motorized powerhead forward on the floor. -
Page 13: Troubleshooting
6. Crack or hole in flex hose other maintenance or service not included in the manual should be performed by an thank you for selecting a bISSEll product. Please do not return this product to the store. w w w . b i s s e l l . c a... - Page 14 9 a.m. — 8 p.m. ET Or visit the BISSELL website www.bissell.ca When contacting BISSELL, have model number of unit available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________ notE: Please keep your original sales receipt. It is your warranty.
- Page 15 - BISSELL CleanAlong Item Part no. 203-7270 203-7268 203-7269 203-7309 203-7310 203-7315 203-7314 203-7273 203-7272 203-7271 203-7274 w w w . b i s s e l l . c a Part name Dust Bag (3pk) Pre-Motor Filter...
-
Page 16: Limited One-Year Warranty
BISSELL Representative at canada.custhelp@bissell.ca or at the phone number below will issue you a Return Authorization Number and a pre-paid mailing label to return the unit to BISSELL for warranty repair. The machine should be returned with a photocopy of your proof of purchase. (Your dated sales receipt is your warranty –...
Need help?
Do you have a question about the CLEANALONG 48K2 and is the answer not in the manual?
Questions and answers