Advertisement
TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:
NOTES TO INSTALLER:
1. Please leave this documentation with the owner of the fixture when finished.
2. Please read this entire booklet before beginning the installation.
3. Check your installation for compliance with plumbing, electrical and other applicable codes.
Murdock warrants that its products are free from defects in material or workmanship under normal use and
service for a period of one year from date of shipment from the factory. Murdocks's liability under this warranty
shall be discharged solely by repair or replacement of defective material, provided Murdock is notified in writing
within the time periods described above.
This warranty does not cover installation or labor charges and does not apply to materials, which have been
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of
the defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this
warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges
caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of
all other warranties expressed or implied. Product maintenance instructions are issued with each unit and
disregard or non-compliance with these instructions will constitute an abnormal use condition and void the
warranty. Stainless steel must be protected on jobsite during construction and must be properly maintained
after the water has been introduced into the water cooler or drinking fountain, or Murdocks's limited warranty is
void.
LIMITED EXPORT WARRANTY - One year on parts only.
Murdock™ assumes no responsibility for use
of void or superseded data. © Copyright
Murdock Mfg., City of Industry, CA Member of
Morris Group International. Please visit
www.murdockmfg.com
for most current
specifications.
7020-956-001
Date: 11/29/17
Cooler Mounted Bottle Fillers
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
BF12 Series
Bottle Filler, Sensor Operated
1.800.591.9360
Technical Assistance Fax: 1.626.855.4894
LIMITED WARRANTY - UNITED STATES & CANADA
Federal
Public Law
111-380
(No Lead)
Member of
MURDOCK
15125 Proctor Ave.
City of Industry, CA
91746 U.S.A.
Phone 800-591-9360
626-336-4561
Fax 626-855-4894
www.murdockmfg.com
Advertisement
Table of Contents
Related Manuals for Murdock H2O To Go BF12 Series
Summary of Contents for Murdock H2O To Go BF12 Series
- Page 1 The repair or replacement of the defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges caused by defects in the materials, or any delay in the repair or replacement thereof.
-
Page 2: Dimensional Drawing
Ø1/4" Holes, 10 Places for Anchoring 1. All dimensions are in inches [MM] Hardware, provided by others MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com... -
Page 3: Prior To Installation
— provided) wall anchors sufficient to secure the fixture. Fixture operates within water pressure range of 20 to 105 PSIG. Murdock will not warranty fixtures damaged when — connected to supply lines with flow pressure lower than 20 PSIG or higher than 105 PSIG. - Page 4 Existing Water Cooler Deck Factory Provided Water Cooler Deck Drinking Fountain Bubbler Locking Grommet MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001 Page 4 of 15...
- Page 5 Water Cooler Deck Drinking Fountain Bubbler Supply Line, Pushbutton to Bubbler Locking Grommet MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001 Page 6 of 15...
- Page 6 Valve that's located on the Mounting Panel. Mounting Panel Shut-Off Valve 1/4" OD PE Tubing & Insulation MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001...
- Page 7 Water Cooler Assembly Mounting Plate Ø1/4" OD PE & Insulation Tubing Shut-Off Valve MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001 Page 7 of 15...
- Page 8 Bottle Count Display, see step 15 before continuing. Sensor Solenoid Valve Power Supply MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001 Page 8 of 15...
- Page 9 Re-mount Water Cooler Access Panel to Water Cooler. Water Cooler Bottle Filler Access Panel MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001 Page 9 of 15...
- Page 10 Water Supply Line, to Bottle Filler 1/4" O.D. Push-In Tee Water Supply Line, Inlet Foam Insulation MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001...
-
Page 11: Electrical Installation
-BCD Bottle Counter Display with Illuminated Display Fill Spout Sensor MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001 Page 11 of 15... - Page 12 -Press and hold Button until the display matches installed Filter type, then release. “FILTER NONE” “FILTER 1500” “FILTER 3000” RESET/MODE BUTTON MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001 Page 12 of 15 Date: 11/29/17...
-
Page 13: Push-In Fitting Installation
Collet in, pull on the PE Tubing to remove from the Push-In Fitting. COLLET MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-956-001... - Page 14 Use clean mild soapy water for powder coated units. 6. Periodically remove panels and clean out inline “Y’’ strainer. MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com...
- Page 15 0116-123-000 #10-32 x 1" BUTTON HEAD SCREW 1895-709-000 ELBOW, 1/4" PUSH-IN x 1/4" STEM 1895-710-000 1/4" PUSH-IN UNION TEE MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com...
Need help?
Do you have a question about the H2O To Go BF12 Series and is the answer not in the manual?
Questions and answers