Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ALDI Lightway BMSL1232
Summary of Contents for ALDI Lightway BMSL1232
- Page 1 User Manual ® SOLAR SPOTLIGHT ID: #05007...
-
Page 2: Table Of Contents
Contents Overview ................. 3 Use ..................4 Package contents/device parts ........5 General information ............6 Reading and storing the user manual ......6 Explanation of symbols ............ 6 Safety ................8 Proper use ................8 Safety instructions ............. 8 Start-up ................14 Checking the spotlight and package contents ... -
Page 4: Use
140° 10 m ± 1 m 1,5 - 2 m... -
Page 5: Package Contents/Device Parts
Package contents/device parts Package contents/device parts Spotlight head, 2× Fixing screw, 2× Sensor housing Sensitivity controller Charging slot Rear panel Power switch Controller for the lighting duration Motion sensor Wall bracket Plug with charging cable Solar panel Screw, 6× Dowel, 6×... -
Page 6: General Information
General information General information Reading and storing the user manual This user manual accompanies this solar spotlight (referred to below as the “spotlight”). It contains important information on start-up and handling. Before using the spotlight, read the user manual carefully. This particularly applies to the safety instructions. - Page 7 General information NOTICE! This signal word warns against potential damages to property. This symbol provides you with useful additional information about start-up or operation. Declaration of conformity (see chapter “Declaration of conformity”): Products marked with this symbol meet all applicable Community regulations for the European Economic Area.
-
Page 8: Safety
Safety Safety Proper use The spotlight is designed as a fixed installation in a location protected against rain and is intended only for temporary lighting outdoors, e.g. to light corridors, garages or pathways and as a deterrent against burglary. Do not use it for indoor lighting or for accent lighting. - Page 9 Safety flammable materials. − Do not continue to use the spotlight if it exhibits damage. Only replace damaged parts with corresponding original spare parts. − Do not open the housing and do not make any modifications to the spotlight. Have only qualified professionals perform repairs.
- Page 10 Safety − Do not take rechargeable batteries apart and do not short-circuit them. Danger of explosion! − Never short circuit the supply terminals. Avoid allowing them to come into contact with metallic objects. − The rechargeable batteries are located inside the housing and are not replaceable.
- Page 11 Safety WARNING! Risk of chemical burns! The spotlight contains rechargeable batteries. Swallowing rechargeable batteries may result in severe internal injuries or even death. − Store both new and used rechargeable batteries so that they are not accessible to children. − If you are no longer able to securely close the casing, in which the rechargeable batteries are located, do not use the spotlight.
- Page 12 Safety CAUTION! Risk of injury! The light emitted by the LEDs is very bright and can damage the eyes if looked at directly. − Never look directly into the light of the spotlight’s LEDs. − Ensure not to shine the light into the eyes of people or animals when inspecting or assembling the spotlight.
- Page 13 Safety in how to safely use the spotlight and understand the risks associated with operating it. The spotlight is not suitable for use by children. Children must not play with the spotlight. − Cleaning and user maintenance must not be performed by children. −...
-
Page 14: Start-Up
Start-up − The LEDs are permanently installed and cannot be replaced. If the light source has reached the end of its service life, replace the entire spotlight. − Stop using the spotlight if its plastic parts exhibit cracks or breaks or are deformed. Only replace damaged parts with corresponding original spare parts. -
Page 15: Charging The Rechargeable Batteries For The First Time
Start-up 1. Take the spotlight out of the packaging. 2. Check to make sure that the delivery is complete (see Fig. A and B). 3. Check whether the spotlight or the individual parts show signs of damage. If this is the case, do not use the spotlight. Contact the manufacturer at the service address specified on the warranty card. -
Page 16: Choosing An Installation Location
Start-up Choosing an installation location Ideal installation location for the spotlight Motion sensors are electronic sensors that recognise movement in their environment and work as electrical switches, responding to this movement. Heat sources are sensed using the lens. If a heat source in the sensor’s range changes or moves, the spotlight will switch one for the configured time. - Page 17 Start-up • The spotlight works best if the sensor area of the motion sensor is crossed horizontally. As far as possible, install the motion sensor in such a way that the main direction of approach is not straight in front of the sensor. Ideal installation location for the solar panel The solar panel is the main source of current for the spotlight.
-
Page 18: Assembly
Assembly Assembly WARNING! Risk of electric shock! Improper installation may result in an electric shock. − Ensure that there are no cables or other electrical lines behind the location where the spotlight is attached. To avoid triggering the spotlight unintentionally, the spotlight must be fitted firmly. -
Page 19: Mounting The Solar Panel
Operation 6. Place the housing of the spotlight onto the rear panel. 7. Fasten the housing on the rear panel by screwing the fixing screw tight. Mounting the solar panel 1. Choose a suitable surface for installation (see chapter “Choosing an installation location”). 2. -
Page 20: Choosing A Lighting Duration
Operation Choosing a lighting duration 1. If necessary, turn the motion sensor housing to reach the controller for the lighting duration 2. Choose the desired lighting duration between approx. 5 seconds and approx. 7 minutes by turning the controller in the corresponding direction: −... -
Page 21: Adjusting The Spotlight Heads
Switching the spotlight on and off Adjusting the spotlight heads You can turn both spotlight heads approx. 180°. The maximum angle of aperture between the two spotlight heads is approx. 320°. You can also move each of the spotlight heads approx. 90° downwards and approx. -
Page 22: Troubleshooting
Troubleshooting Troubleshooting Fault Possible cause Solution The spotlight The rechargeable Remove any dust, dirt does not batteries are or snow from the solar switch on discharged. panel and re- despite position it if necessary. movement in The rechargeable Contact the After Sales the sensor batteries are faulty. - Page 23 Troubleshooting Fault Possible cause Solution The LEDs The rechargeable Select another instal- shine less batteries could not lation location for the brightly. charge sufficiently solar panel (see because the solar chapter “Choosing an panel is not receiv- installation location”). ing enough direct Note that there is solar radiation or generally less sunlight...
- Page 24 Troubleshooting Fault Possible cause Solution The spotlight The following Find a more suitable turns on for movements or location for mounting no obvious heat sources can the spotlight or change reason. activate the sensor: the sensor area by Air conditioning turning the motion units, chimneys, sensor housing...
-
Page 25: Cleaning
Cleaning Cleaning NOTICE! Risk of damage! Improper handling of the spotlight may result in damage to the spotlight. − Do not clean the spotlight and accessories under running water and do not spray the spotlight with the garden hose or a high-pressure cleaner. -
Page 26: Storage
Storage Storage − Store the spotlight in an area inaccessible to children in a dry and light-free area. Technical data Model: BMSL1232 Article number: 97476 Spotlight dimensions (L × W × H): 13 × 18 × 23 cm Solar panel dimensions (L × W × H): 4 ×... - Page 27 Technical data Warming up time (95 %): < 1 s Number of switching cycles: > 15,000 Dimmable: Risk group (according to EN 62471:2008): Minimum distance to illuminated objects: 1 m Plastic protective screen: ∅ 60 mm, thickness 3 mm Type of protection: IP44 Motion sensor Sensor angle:...
-
Page 28: Declaration Of Conformity
Declaration of conformity Declaration of conformity We, AHG Wachsmuth & Krogmann mbH, Lange Muehren 1, D-20095 Hamburg, Germany, declare under our sole responsibility that the product mentioned above complies with the essential re- quirements of the stated EU Directive. The EU Dec- laration of Conformity can be requested from the address specified on the warranty card (at the end of this user manual). - Page 29 Disposal Batteries and rechargeable batteries must not be disposed of in the household waste! As the end user you are required by law to bring all batteries and rechargeable batteries, regardless of whether they contain harmful substances* or not, to a collection point run by the communal authority or borough or to a retailer, to allow them to be disposed of in an environmentally friendly manner.
- Page 30 PRODUCED IN CHINA FOR: ALDI STORES LTD. PO BOX 26, ATHERSTONE WARWICKSHIRE, CV9 2SH ALDI STORES (IRELAND) LTD.
Need help?
Do you have a question about the Lightway BMSL1232 and is the answer not in the manual?
Questions and answers