Table of Contents
Advertisement
Advertisement
Chapters
Table of Contents
Related Manuals for Rohde & Schwarz TSME6
Summary of Contents for Rohde & Schwarz TSME6
- Page 1 ® R&S TSME6 Ultra Compact Drive Test Scanner Getting Started (a00K2) 4900002702...
- Page 2 Rohde & Schwarz GmbH & Co. KG. Trade names are trademarks of the owners. ® 4900.0027.02 | Version 02 | R&S TSME6 Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol , e.g. ® R&S TSME6 is indicated as R&S TSME6.
-
Page 3: Table Of Contents
® Contents R&S TSME6 Contents 1 Safety Information..............5 2 Documentation Overview............6 2.1 Getting Started Manual.................6 2.2 User Manuals and Help................ 6 2.3 Tutorials....................6 2.4 Basic Safety Instructions..............6 2.5 Brochures and Data Sheets..............7 2.6 Application Notes, Application Cards, White Papers, etc....7 3 Key Features................ - Page 4 ® Contents R&S TSME6 Getting Started 4900.0027.02 ─ 02...
-
Page 5: Safety Information
TSME6 Safety Information The product documentation helps you to use the R&S TSME6 safely and effi- ciently. Follow the instructions provided here and in the printed "Basic Safety Instructions". Keep the product documentation nearby and offer it to other users. -
Page 6: Documentation Overview
Getting Started Manual Introduces the R&S TSME6 and describes how to set up and start working with the product. Includes basic operations, typical measurement examples, and gen- eral information, e.g. safety instructions, etc. A printed version is delivered with the instrument. -
Page 7: Brochures And Data Sheets
Application Notes, Application Cards, White Papers, etc. Brochures and Data Sheets The data sheet contains the technical specifications of the R&S TSME6. It also lists the firmware applications and their order numbers, and optional accessories. The brochure provides an overview of the instrument and deals with the specific characteristics. -
Page 8: Key Features
Key Features R&S TSME6 Key Features The R&S TSME6 sets standards in RF performance and usability. Outstanding key features are: ● Simultaneous measurements with no limitations in 3GPP frequency bands and technologies with SIB/L3 decoding support up to 6GHz ● More than ten technologies simultaneously in one scanner ●... -
Page 9: Preparing For Use
Putting into Operation This section describes the basic steps to be taken when setting up the R&S TSME6 for the first time. Risk of injury due to disregarding safety information Observe the information on appropriate operating conditions provided in the data sheet to prevent personal injury or damage to the instrument. - Page 10 ® Preparing for Use R&S TSME6 Putting into Operation Instrument damage caused by electrostatic discharge Electrostatic discharge (ESD) can damage the electronic components of the instrument and the device under test (DUT). Electrostatic discharge is most likely to occur when you connect or disconnect a DUT or test fixture to the instrument's test ports.
-
Page 11: Unpacking And Checking The Instrument
Cascading R&S TSME6s Rackmounting The R&S TSME6 can be installed in a 19 inch rack using a rack adapter kit for one to four R&S TSME6s (option R&S TSME6-Z2, R&S no. 4900.1030.02). The installation instructions are part of the adapter kit. - Page 12 ® Preparing for Use R&S TSME6 Putting into Operation Figure 4-1: Rackmounting of 2 R&S TSME6s Figure 4-2: Rackmounting of 2 R&S TSME6s (reverse orientation of R&S TSME6s) Getting Started 4900.0027.02 ─ 02...
- Page 13 ® Preparing for Use R&S TSME6 Putting into Operation Figure 4-3: Rackmounting of 4 R&S TSME6s Figure 4-4: Rackmounting of 4 R&S TSME6s (reverse orientation of R&S TSME6s) Getting Started 4900.0027.02 ─ 02...
- Page 14 The R&S TSME6 draws in fresh air from the front pane and warm air flows out at its panes. Thus, if no active cooling is installed, ensure that the following surrounding spaces to the instrument are kept clear: ●...
- Page 15 3. Push the 1 R&S TSME6 to the front until the mechanism locks. To disconnect the R&S TSME6 lift the release button on the pane of the upper R&S TSME6 and slide it until the device is released. Getting Started 4900.0027.02 ─ 02...
-
Page 16: Connecting The Dc Power Supply
● Cigarette lighter power supply (for example in a vehicle) using the supplied DC power cable ● Optional AC power supply and power cable R&S TSME6-Z1 (see ) ● Proprietary power supply with an adapted power cable Using the supplied cigarette lighter power supply cable ►... - Page 17 Putting into Operation Connecting a proprietary power supply ► To use a proprietary DC supply with the R&S TSME6 power cable, demount the cigarette lighter adapter from the supplied power cable and connect the open ends of the cable to the proprietary power supply. Be sure to respect the...
-
Page 18: Setting Up The Lan Connection To The Host Pc
4.1.5 Setting Up the LAN Connection to the Host PC To control and run measurements with the R&S TSME6, a host PC or notebook with LAN interface is required. The R&S TSME6 is equipped with a network interface and can be connected to an Ethernet LAN (local area network). - Page 19 Note: This is the IP address set by the R&S TSME Device Manager. ● "Static IP" operating mode IP address is manually set on PC and a static IP used on R&S TSME6 if the following conditions are met: – PC LAN interface is configured to use a user defined IP address, not in range 169.254.0.1 –...
- Page 20 These ranges are important to prevent conflicts with IP addresses dynami- cally generated for the PC LAN interfaces. Note: If a R&S TSME6 is shared with 2 or more PCs, and its stored IP address is not in the defined range above, this may lead in rare cases to IP conflicts.
- Page 21 IP address 192.168.0.1 to the host PC or configure the host PC to obtain an IP address automatically ("Auto-IP"). To control the R&S TSME6 from the host PC, the LAN interface of the host PC must be configured as follows: 1.
- Page 22 ® Preparing for Use R&S TSME6 Putting into Operation 6. Select the "Properties" button. 7. Configure the following TCP/IP settings: a) Use any "Auto-IP" operating mode. Select "Obtain an IP address automatically". Getting Started 4900.0027.02 ─ 02...
- Page 23 ® Preparing for Use R&S TSME6 Putting into Operation b) Use "Static IP" operating mode. ● Select "Use the following IP address" (fixed IP, no dynamic range) ● IP address: 192.168.0.1 (recommended) ● Subnet mask: 255.255.255.0 ● No Default Gateway 8.
- Page 24 See R&S TSME6 User Manual, chapter Troubleshooting for help. 9. Close the Control Panel, reboot the host PC and check if the connection can be established successfully (see R&S TSME6 User Manual, chapter Trouble- shooting for help.). If your firewall is active, make sure that it is configured as described in Chapter 4.1.5.2, "Firewall...
- Page 25 ● Multicast IP address for TSME: 224.17.4.76 ● Multicast Address for TSME6: 239.192.1.7 ● IP-Address of TSME6 has to be allowed as well: 192.168.0.2 (example) Note: In "full auto-IP" operating mode, the IP address generated for the R&S TSME6 has to be allowed.
-
Page 26: Connecting External Devices
Chapter 4.1.4, "Connecting the DC Power Supply", on page 16. ● Connect the PC or notebook LAN port to the LAN port of the R&S TSME6 as described in Chapter 4.1.5, "Setting Up the LAN Connection to the Host PC", on page 18. -
Page 27: Connecting A Kensington Lock
4.1.7 Connecting a Kensington Lock The R&S TSME6 provides a connector for a Kensington lock, which can be used to secure a mobile device against theft. The connector is located on the side panel of the instrument. -
Page 28: Enabling Untethered Dead Reckoning
33) of the R&S TSME6. 1. Mount the R&S TSME6 device fixed to the frame of a car. 2. Power on the R&S TSME6 device. 3. Activate "Dead Reckoning" in the used software (for details, refer to R&S ROMES, R&S NESTOR or R&S ViCom documentation). -
Page 29: Switching The Instrument On And Off
Switching off the instrument When you press the On/Off key on the rear panel of the R&S TSME6 to switch it off, the instrument changes to standby mode. In standby mode, the program exe- cution on the instrument is stopped immediately, but the instrument is still under power connection. - Page 30 ® Preparing for Use R&S TSME6 Switching the Instrument On and Off Removing the power supply If you remove the power supply and reconnect it later, the instrument automati- cally boots when power returns. Getting Started 4900.0027.02 ─ 02...
-
Page 31: Instrument Tour
Front Panel View Instrument Tour Front Panel View The front panel of the R&S TSME6 does not provide any connectors or control elements for operation. Behind the right side of the rear panel (with the ventilation openings), 4 status LEDs are located. These LEDs display the following states: ●... -
Page 32: Rear Panel View
Rear Panel View This figure shows the rear panel view of the R&S TSME6. The individual ele- ments are described in more detail in the subsequent sections. Figure 5-2: R&S TSME6 - rear panel... - Page 33 R&S TSME6 connected to one host PC. LAN connector with LEDs The LAN connector provides a high-speed Gigabit Ethernet interface with an RJ 45 connector using IPv4. It is required to connect the R&S TSME6 to a host PC. Getting Started 4900.0027.02 ─ 02...
- Page 34 ® Instrument Tour R&S TSME6 Rear Panel View The LEDs on the LAN connector indicate the status of the connection to the host PC. LED 1 is on the left side of the connector, LED 2 is on the right.
- Page 35 FGPA configuration in progress (2 Hz) green FPGA configuration finished, preparing for start (up to 5 seconds during startup) green R&S TSME6 ready, not connected green green connected green, blinking green measuring rapidly green, blinking green...
-
Page 36: Index
® Index R&S TSME6 Index Application cards ........7 Safety instructions ........6 Application notes ........7 Standby mode ......... 29 Brochures ..........7 Tutorials ............. 6 Connectors User manual ..........6 LAN ............. 33 White papers ..........7 Data sheets ..........7 Dead reckoning ........
Need help?
Do you have a question about the TSME6 and is the answer not in the manual?
Questions and answers