Related Manuals for Oliver 6910
Summary of Contents for Oliver 6910
- Page 1 6910 Spindle Sander Owner’s Manual Oliver Machinery M-6910 12/2003 Seattle, WA Copyright 2005 www.olivermachinery.net...
-
Page 2: Warranty
Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your OLIVER Sander, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully. - Page 3 • ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING. • REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position before plugging in. Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net...
- Page 4 • USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by OLIVER may cause hazards or risk of injury to persons. • NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped. • CHECK DAMAGED PARTS. Before further use of the machine, a guard or other part that is damaged should...
-
Page 5: Grounding Instructions
This adapter is not applicable in Canada. The green colored rigid ear, lug, or tab, extending from the adapter, must be connected to a permanent ground such as a properly grounded outlet box, as shown in (B). Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net... -
Page 6: Table Of Contents
Breakdown and Parts List ......................12-17 Wiring Diagram..........................18 The specifications in this manual are given as general information and are not binding. OLIVER reserves the right to effect, at any time and without prior notice, changes or alterations to parts, fittings, and accessory equipment deemed necessary for any reason whatsoever. -
Page 7: Warnings
JET has a Heavy Duty Universal Mobile Base that will fit this sander. JET also has a variety of Dust Collectors and Air Filtration Units that will work nicely with your new sander. Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net... -
Page 8: Mounting Sanding Sleeves
1. Disconnect the sander form the power source, unplug. 2. Use the provided wrenches to hold the upper arbor housing nut (E, Fig. 3) while turning the arbor nut (D, Fig. 3) counter- clockwise. Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net... -
Page 9: Sanding Assembly 90° To Table
90° to the sanding drum. 6. Tighten the hex nut while holding the stop. 7. Adjust pointer (G, Fig. 6) so that it indicates the “0” position on the scale. Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net... -
Page 10: Replacing Sanding Sleeves
3. The oil sight glass (E, Fig. 8) should read between the “high” and “low” marks. Keep the machine and all attachments clean. All bearings are permanently lubricated and require no further service. Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net... -
Page 11: Troubleshooting
Sanding marks on wood 1. Wrong grit sanding sleeve 1. Use coarser grit for stock removal 2. Feed pressure too great and fine grit for finish sanding. 2. Never force workpiece Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net... -
Page 12: Breakdown And Parts List
Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net... - Page 13 Washer 3/8” S0240600A Width Pointer 40301032 Screw S0030304 30101049 30101050 Wrench 30105054A Arbor 30105055 Hex Nut 30105056 Spring Pin S0313525 P.V.C 30105057 Washer 30105058 30105059 Sanding Cloth 30105060 P.V.C 30105061 Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net...
- Page 14 Screw S0030324 143a S0110300 Vent Hood 30101002j-1 Column 30101001JM Motor Bracket 30101003a Motor M0000000 Strain Relief Bushing S1006P1 Spring Washer S0230506 Coupling Head 30102008a Tank Lid 30101009a Set Screw S0050404 Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net...
- Page 15 30105051a Table Insert (small) 30105052a Table Insert (Large) 30105053a Screw 3/8”-16UNCx1” S0020612 Fixed Rod 30101027a Nut 3/8”-16UNC S0110600 Rubber Feet 10401029 Sinking Head Screw S0030512 Rd. Cross hd. Screw S0110300 Oliver Machinery Seattle, WA | Copyright 2005 | www.olivermachinery.net...
- Page 17 6910 Parts List PART No. DESCRIPTION REF No. QTY. Power Cord L0000001e S0410525 Oil lndicator 30101011 Oil Seal 30101014 Ball Bearing C1206206 C Snap Ring S0526500 Sleeve 30103014 Guide Rail Shaft 30103015 Ball Bearing C1206205 Locking Nut 30103016 Worm 30103017...
-
Page 18: Wiring Diagram
30105059 Sanding Cloth 30105060 P.V.C 30105061 Sanding Cloth 30105062 Washer 30105063 P.V.C 30105064 Sanding Cloth 30105065 Washer 30105066 P.V.C 30105067 Sanding Cloth 30105068 Washer 30105069 P.V.C 30105070 Sanding Cloth 30105071 Washer 30105072 Sanding Cloth 30105073 Arbor 30105074 Hex Nut 30105075 Sanding Cloth 30105076 Arbor... - Page 19 Strain Relief Bushing S1006P1 Spring Washer S0230506 Coupling Head 30102008a Tank Lid 30101009a Set Screw S0050404 Tank Lid 30101013a Switch W0000003P Rear Trunnion 30101033a Locking Knob 30101031j Dust Cover 30101034a Hex Screw S0020501 S0110500 Working Table 30100002JM Scale 30101047a Table Insert (medium) 30105051a Table Insert (small) 30105052a...
Need help?
Do you have a question about the 6910 and is the answer not in the manual?
Questions and answers