La Marzocco Strada AV Operating Manual
  1. Manuals
  2. Brands
  3. La Marzocco Manuals
  4. Coffee Maker
  5. Strada AV
  6. Operating manual

La Marzocco Strada AV Operating Manual

Hide thumbs Also See for Strada AV:
Table of Contents

Advertisement

Quick Links

manual
strada av
The Strada AV is characterized by its underlying mechanical features
and design of the Strada. The initials "AV" refer to a feature whereby
brewing is activated by a three button keypad where the doses
are counted by a flowmeter for each group. This model includes
proportional steam valves, both featuring anti-resuction valves.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Strada AV and is the answer not in the manual?

Questions and answers

Related Manuals for La Marzocco Strada AV

Summary of Contents for La Marzocco Strada AV

  • Page 1 The Strada AV is characterized by its underlying mechanical features and design of the Strada. The initials “AV” refer to a feature whereby brewing is activated by a three button keypad where the doses are counted by a flowmeter for each group. This model includes...

  • Page 2: Table Of Contents

    Operating Manual V2.0 - 12/2016 MAN.16.1.02 Chapters page 3 La Marzocco S.r.l. 1. General Warnings and Safety Specifications page 7 2. Definition of Available Models Via La Torre 14/H Località La Torre 50038 Scarperia e San Piero page 10 3.

  • Page 3: General Warnings And Safety Specifications

    1. General Warnings and Safety Specifications years of age) with reduced WARNING CAUTION physical, sensory or mental This machine is for professional As already mentioned in capabilities, or lack of use only and should be installed the preceding notes, the experience and knowledge, in locations where its use and manufacturer shall not be held...
  • Page 4 must be supplied to users. on any further and contact your codes. installation Users are asked to read dealer or retailer immediately. They also must comply to the the enclosed warnings and will send out specialized personnel manufacturer’s instructions, authorized to perform service on cautions carefully, as they and must be performed by provide valuable information...
  • Page 5 been done properly as it indicated on such adapters • do not use extension cords represents fundamental and extension cords. in bath or shower rooms; safety requirement. Ensure • do not unplug the device 12) This device must be used qualified personnel check...
  • Page 6 Any repairs must be performed exclusively 19) The machine’s power by the manufacturer or by supply cable must not be an authorized centre using STRADA AV 2 groups 3 groups replaced by users. In case the only original parts.

  • Page 7: Definition Of Available Models

    2. Definition of Available Models This operating manual refers exclusively to the following models, of our own manufacture: STRADA, model AV 3 groups Legend Main Switch Pressure Gauge (steam boiler) Pressure Gauge (coffee boiler) Brew Groups Cup Warmer Button Tea Water Button Digital Display Steam Wand Steam Wand Lever...
  • Page 8 1) General Description by temperature probe and PID controller. is a list of effective volume and power The machine is built in 2 and 3 coffee The steam boiler has various fittings used ratings according to the number of groups group versions and is essentially composed for safety devices, for supplying hot water installed:...
  • Page 9 • Brewing groups • Water pump • Machine CE plate: They consist of a precision casting made The rotary vane pump, is installed on the of stainless steel. The brewing group water supply tubing and is set up to operate accepts the portafilter used to hold the anytime the coffee groups are activated, ground coffee;...

  • Page 10: Installation

    The machine is intended to be WATTAGE WATTAGE AC220-240V/60Hz 20-22 AC208-240/60Hz 4600 1600 3000 4600 SEE ELECTRICAL permanently connected to fixed AC380/50Hz STRADA AV CONNECTIONS AC220-240V/60Hz 25-29 wiring, and it is mandatory that 2400 4000 6400 6400 30,5 AC208-240/60Hz FOR DETAILS AC380/50Hz...
  • Page 11 WARNING WARNING WARNING At each installation, the Hazardous voltage disconnect This appliance is not intended machine should be equipped from power supply before for use by persons (including with a new set of tubes for servicing. children) with reduced physical, plumbing and related gaskets.
  • Page 12 1) Installation guide If the pressure and flow are not adequate, WARNING For best results, STRADA needs a air bubbles may develop within the gears. In order to prevent cracks minimum flow of water in input of 100 l/h This is called cavitation. Cavitation can or leakage: do not store or and a pressure of 2.5 bar.
  • Page 13 Pressure higher than 9 bar Flow rate lower than 100 l/h Installation pressure reducer immediately after the water treatment system, upstream of the rotary pump. Installation of the rotary pump (set to 9 bar) immediately after the pressure reducer, upstream of the tee. POWER SUPPLY STEAM COFFEE...
  • Page 14 2) Accessories interlock switch Total Chlorine, pH & Total Alkalinity, Check the package to make sure that the • Three-phase, 380VAC Chlorides. following accessories are included: electrical connection with neutral + Ideally, you should perform a test on the • a number of 1-dose and 2-dose ground, near the bench on which the water BEFORE the water treatment system...
  • Page 15 5) Water supply connection properly. Connect water supply versions, secured to espresso machine via In order to connect the machine up to connection of the espresso machine to a strain relief connector. the water mains proceed according to the the water pump outlet using one of the b) Water pump motor power cord indications given in the chapter about supplied stainless steel braided hoses.
  • Page 16 - Cable connection; 7) Waste water drain connection The espresso machine drain is to be connected by means of the included reinforced plastic tubing. Connect one end of the reinforced plastic tubing to the drain hose connection on the left side of the espresso machine, secure with included hose clamp.

  • Page 17: Machine Operation And Coffee Preparation

    4. Machine Operation and Coffee Preparation group assemblies. CAUTION WARNING To remove the air from the boiler, or “bleed Never remove the filter holder This machine is designed only for the groups”, it will be necessary to remove when water is being delivered. preparing coffee and hot drinks.
  • Page 18 will be switched on, activating the auto-fill is necessary to adjust the expansion valve • Turn on the hot water valve for the solenoid valve and the motor pump. This (see the picture below about the three time necessary to allow the following will fill the steam boiler to a predetermined coffee boiler expasion valves) in such a quantities of water to be brewed:...
  • Page 19 Note: When the heating element in the The size of the coffee granules is extremely Filter Basket coffee boiler is energized, the water will important in preparing a good cup of Porta Filter expand increasing the start-up pressure. coffee, other than the type of coffee mix Once the maximum pressure is reached, used, quite obviously.

  • Page 20: Dispensing Steam And Hot Water

    5. Dispensing Steam and Hot Water 1) Steaming milk or other liquids This condition is undesireable and can 2) Preparing tea and other hot drinks. In order to allow for any condensed water cause contamination in the steam boiler. in the wand to be released ALWAYS allow After use remember to purge the wand by some steam to be discharged by turning on opening the steam valve for a few seconds,...

  • Page 21: Maintenance And Periodic Cleaning Operations

    6. Maintenance and Periodic Cleaning Operations WARNING WARNING WARNING If the above-mentioned The machine must be installed so This machine is for professional instructions are not adhered that qualified technical presonnel use only and should be installed to the manufacturer cannot be can easily access it for eventual in locations where its use and held responsible for damage to...
  • Page 22 2) Cleaning filters Rinse thoroughly with clean water. Install 6) Cleaning the hot water and steam nozzles - Put 2 or 3 teaspoons of detergent powder and run hot water through each group Steam nozzles must cleaned for coffee machines in about 1/2 a litre several times with the screen installed.

  • Page 23: De-Commissioning And Demolition

    each steam wand for at least one minute. follow these safety indications: Turn on the hot water valve for the time Disconnect the machine from the water necessary to allow the following quantities mains or interrupt the water connection of water to be brewed: via a mains tap.

  • Page 24: Mandatory Maintenance And Check-Up Operations

    8. Mandatory Maintenance and Check-up Operations These operations are in addition to the Maintenance and Periodic Cleaning Operations as specified in Chapter 6. The following maintenance and check-up operations sould be carried out by a qualified technician. The time required for the periodic maintenance is determinated by the quantity of daily work and/or coffee consumption. N.B.

  • Page 25: Precision Scale

    9. Precision Scale WARNING Legend Handle with care maximum load Scale crosspiece 1Kg do not lift. Drain grille Scale individual grid WARNING Removable drain tray The individual grid of the scale is a fragile component, handle and store with care. WARNING The height of the bottom tray is fixed.
  • Page 26 - To avoid contact with dirt before placing the filter holder, clean and dry the grid; - Use only original La Marzocco filters and - Please be careful during the cleaning filter holders, identified by the following...
  • Page 27 3) Removing the electronic box To remove the electronic box you need to remove the lower front panel, unscrew and remove the lower screws , loosen the upper screws without removing them and move the scale crosspiece up. Now you can access the electronic box or remove it.

  • Page 28: Software Programming Guide

    10. Software Programming Guide Programming Introduction “Technical” Programming Digital Display page 29 Language page 63 Programming Keypad page 30 Temperature Measurement Units page 64 page 31 Start Up Procedures Name page 65 Shut Down Procedures page 32 Program Doses page 66 page 33 Accessing Programming Mode Scales (ABR version)

  • Page 29: Programming Introduction

    Programming Introduction Description • This espresso machine has a CPU and many configurable settings. • Additionally, there are many feedback controls employed in this espresso machine to troubleshoot problems should they occur. • The following is a brief introduction to the controls and display and how they interact with the operator. Digital Display Digital display 2nd group coffee boiler temperature...

  • Page 30: Programming Keypad

    Programming Keypad The keypad has two functions. The first is for control of the espresso. The second is for programming individual software parameters. The programming of the individual parameters is possible only using the buttons in the group 1 (group starting from the left). Button Description This button is used to control the brewing of the single espresso.

  • Page 31: Start Up Procedures

    Start Up Procedures Description Turning the Espresso Machine On The following is the procedure for turning • Proceed checking for water connection on the power to the espresso machine. to the espresso machine. • Please follow the procedures carefully • Proceed making sure you have filled the to avoid any damage to the espresso boilers.

  • Page 32: Shut Down Procedures

    Shut Down Procedures Description Turning the Espresso Machine Off The following is the procedure for turning • This machine has two off settings. One off power to the espresso machine. setting turns off all of the components • Please follow the procedures carefully in the espresso machine and the other to avoid any damage to the espresso turns off power to the complete espresso...

  • Page 33: Accessing Programming Mode

    Accessing Programming Mode Description quality of the espresso. Programming Mode No password is required for access. • Technical Programming - The parameters • To change the values of any parameter contained within this level are ones the operator must first enter into the the operator can change to affect the programming mode.

  • Page 34: Cleaning Cycles

    Cleaning Cycles Description Cleaning Cycles • This parameter allows the operator • The rinsing procedure is provided to give to carry out the washing of the coffee the operator more flexibility and freedom groups, in an automatic way, by running with regard to this operation.

  • Page 35: Brewratio (Abr Version)

    “Barista” Programming (only on ABR espresso machine models) Description Brewratio The procedure for weighing the filter • To brew in brew ratio mode, set this holder either empty or filled with coffee mode by entering the software settings. powder is shown below. •...

  • Page 36: Program Doses

    “Barista” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 37 “Barista” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 38 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. weight) for each button on the keyboard.
  • Page 39 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. weight) for each button on the keyboard.
  • Page 40 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to select the coffee brewing mode among those available: pulse, mass and brew ratio. Group Dose • PULSE mode: control of doses in volume Settings •...
  • Page 41 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to select the coffee brewing mode among those available: pulse, mass and brew ratio. Group Dose • PULSE mode: control of doses in volume Settings •...
  • Page 42 “Barista” Programming Description Program Dose • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key. set each key. G1 Dose Settings Display Operating Procedure...
  • Page 43 “Barista” Programming Description Program Dose • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key. set each key. G1 Dose Settings Display Operating Procedure...
  • Page 44 “Barista” Programming (only on ABR espresso machine models) Description Program Dose • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key. set each key.
  • Page 45 “Barista” Programming (only on ABR espresso machine models) Description Program Dose • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key. set each key.
  • Page 46 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.
  • Page 47 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.
  • Page 48 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • The dose can be set by pulses or by view and manually change each dose for mass (weight). each key. •...
  • Page 49 “Barista” Programming Description Program Dose • This parameter allows the operator to copy the doses present of each key to the others. Copy Dose Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista”...
  • Page 50 “Barista” Programming Description Program Dose • This parameter allows the operator to copy the doses present of each key to the others. Copy Dose Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. LaMarzocco 09:30 Press T2 and T3...
  • Page 51 “Barista” Programming Description Program Dose • This parameter allows the operator to cancel all the doses set. Reset Volume Doses Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming. LaMarzocco 09:30 94.5 94.6 94.5 SB After about 5 seconds the following screen is displayed.
  • Page 52 “Barista” Programming Description Program Dose • This parameter allows the operator to cancel all the doses set. Reset Volume Doses Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. LaMarzocco 09:30 Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the 94.5 94.6 94.5 SB...

  • Page 53: Scales (Abr Version)

    “Barista” Programming (only on ABR espresso machine models) Description Program Scales • This parameter enables the technician to set some scale parameters like: Enabling/disabling offset parameter; Scales - Setting the weight reading time; Configuration - Calibrating the scales. Display Operating Procedure When the espresso machine is turned on, press and hold the T3 to access the “Barista”...
  • Page 54 “Barista” Programming (only on ABR espresso machine models) Description Program Scales • This parameter enables the technician to set some scale parameters like: Enabling/disabling offset parameter; Scales - Setting the weight reading time; Configuration - Calibrating the scales. Display Operating Procedure Press the T3 button to return to the “Barista”...

  • Page 55: Tea Dose

    “Barista” Programming Description Tea Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the tea button. Settings Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista”...
  • Page 56 “Barista” Programming Description Tea Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the tea button. Tea Dose Settings Display Operating Procedure To program the brewing time, press the tea button to start and then press it again to stop when the desired Press Tea Button To Stop dose is achieved.
  • Page 57 “Barista” Programming Description Tea Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the tea button. Settings Display Operating Procedure Tea Dose Press the T3 button to return to the “Barista”...

  • Page 58: Coffee Boiler

    “Barista” Programming Description Coffee Boiler • This parameter allows the operator to • This parameter allows the operator to enable/disable the coffee boiler. program the coffee boiler temperature. Each group can have a different programming. Coffee Boiler Settings Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista”...
  • Page 59 “Barista” Programming Description Coffee Boiler • This parameter allows the operator to • This parameter allows the operator to enable/disable the coffee boiler. program the coffee boiler temperature. Each group can have a different programming. Coffee Boiler Settings Display Operating Procedure CB Settings To exit the menu move between the parameters using the buttons T1 and T2...

  • Page 60: Pre-Infusion Or Pre-Brewing

    “Barista” Programming Description Pre-Infusion or Pre-Brewing • This parameter allows the operator to pre-brewing cycle; during this time the program the time of pre-brewing of pump is active. Once the pre-brewing water with the coffee. Each group can cycle is over, the normal brewing cycle have a different programming.

  • Page 61: Cup Warmer

    “Barista” Programming Description Cup Warmer • This parameter allows the operator to • This function is displayed only on the enable or disable the cups heating models of espresso machine equipped function. with this accessory. Cup Warmer DISABLED Display Operating Procedure LaMarzocco 09:30 When the espresso machine is turned on, press and hold the T3 button .

  • Page 62: Exit Menu

    “Barista” Programming Description Exit Menu • This parameter allows the operator to exit the “Barista” programming and return to the normal use of the espresso machine. Exit Menu Display Operating Procedure Exit Press the T3 button to exit the “Barista” programming and return to the normal use of the espresso Menu machine.

  • Page 63: Language

    “Technical” Programming Description Language • This parameter allows the technician to change the language of the display. Language ENGLISH Display Operating Procedure LaMarzocco 09:30 When the espresso machine is turned on, press and hold the T3 button . After about 10 seconds the 94.5 94.6 94.5 SB following screen is displayed.

  • Page 64: Temperature Measurement Units

    “Technical” Programming Description Temperature Measurement Units • This parameter allows the technician to change the temperature display from degrees Celsius to degrees Fahrenheit and vice versa. Temp Units CELSIUS Display Operating Procedure Enter Password After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 ****** until the following screen is displayed.

  • Page 65: Name

    “Technical” Programming Description Name • This parameter allows the technician to • The user name is displayed continuously program a 16 character user name. on the display on the second line. Name LaMarzocco Display Operating Procedure Enter Password After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 ****** until the following screen is displayed.

  • Page 66: Program Doses

    “Technical” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 67 “Technical” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 68 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. weight) for each button on the keyboard.
  • Page 69 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. weight) for each button on the keyboard.
  • Page 70 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to select the coffee brewing mode among those available: pulse, mass and brew ratio. Group Dose • PULSE mode: control of doses in volume Settings •...
  • Page 71 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to select the coffee brewing mode among those available: pulse, mass and brew ratio. Group Dose • PULSE mode: control of doses in volume Settings •...
  • Page 72 “Technical” Programming Description Program Dose • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key. set each key. G1 Dose Settings Display Operating Procedure...
  • Page 73 “Technical” Programming Description Program Dose • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key. set each key. G1 Dose Settings Display Operating Procedure...
  • Page 74 “Technical” Programming (only on ABR espresso machine models) Description Program Dose • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key. set each key.
  • Page 75 “Technical” Programming (only on ABR espresso machine models) Description Program Dose • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key. set each key.
  • Page 76 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.
  • Page 77 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.
  • Page 78 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • The dose can be set by pulses or by view and manually change each dose for mass (weight). each key. •...
  • Page 79 “Technical” Programming Description Program Dose • This parameter allows the operator to copy the doses present of each key to the others. Copy Dose Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 LaMarzocco 09:30 94.5 94.6 94.5 SB until the following screen is displayed.
  • Page 80 “Technical” Programming Description Program Dose • This parameter allows the operator to copy the doses present of each key to the others. Copy Dose Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. LaMarzocco 09:30 Press T2 and T3...
  • Page 81 “Technical” Programming Description Program Dose • This parameter allows the operator to cancel all the doses set. Reset Volume Doses Display Operating Procedure LaMarzocco 09:30 After accessing the “Technical” programming menu and entering the password, use the buttons T1 94.5 94.6 94.5 SB until the following screen is displayed.
  • Page 82 “Technical” Programming Description Program Dose • This parameter allows the operator to cancel all the doses set. Reset Volume Doses Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. LaMarzocco 09:30 Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the 94.5 94.6 94.5 SB...

  • Page 83: Scales (Abr Version)

    “Technical” Programming (only on ABR espresso machine models) Description Program Scales • This parameter enables the technician to set some scale parameters like: Enabling/disabling offset parameter; Scales - Setting the weight reading time; Configuration - Calibrating the scales; - Updating the scale software. Display Operating Procedure Enter Password...
  • Page 84 “Technical” Programming (only on ABR espresso machine models) Description Program Scales • This parameter enables the technician to set some scale parameters like: Enabling/disabling offset parameter; Scales - Setting the weight reading time; Configuration - Calibrating the scales; - Updating the scale software. Display Operating Procedure Calibrate...
  • Page 85 “Technical” Programming (only on ABR espresso machine models) Description Program Scales • This parameter enables the technician to set some scale parameters like: Enabling/disabling offset parameter; Scales - Setting the weight reading time; Configuration - Calibrating the scales; - Updating the scale software. Display Operating Procedure G1 Scale...

  • Page 86: Tea Dose

    “Technical” Programming Description Tea Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the tea button. Settings Display Operating Procedure Enter Password After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 ****** until the following screen is displayed.
  • Page 87 “Technical” Programming Description Tea Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the tea button. Tea Dose Settings Display Operating Procedure To program the brewing time, press the tea button to start and then press it again to stop when the desired Program Tea Dose dose is achieved.
  • Page 88 “Technical” Programming Description Tea Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the tea button. Tea Dose Settings Display Operating Procedure Tea Dose Press the T3 button to return to the “Technical”...

  • Page 89: Coffee Boiler

    “Technical” Programming Description Coffee Boiler • This parameter enables the technician though the temperature of the boiler to set various parameters of the coffee may vary slightly, the temperature of the boiler. water exiting the group is constant. • The temperature boiler •...
  • Page 90 “Technical” Programming Description Coffee Boiler compensated by use of the “Coffee T. • It is not recommended that this number Offset” parameter. is changed. Changes to this parameter • The OFFSET parameter is used to can cause unexpected results. calibrate the coffee boiler temperature •...

  • Page 91: Steam Boiler

    “Technical” Programming Temperature Pressure Description Steam Boiler 247°F/119°C 1.0 bar • This parameter enables the technician 260°F/127°C 1.5 bar to set various parameters of the steam boiler. 264°F/129°C 2.0 bar • The temperature of saturated water is Steam Boiler proportional to the pressure inside the •...
  • Page 92 “Technical” Programming Description Steam Boiler • The parameter filling WITH PUMP allows the overall dispensing pressure in the brew the technician to select the activation of boiler. the water pump during the automatic • During the auto-fill cycle, if a brew cycle is filling cycle of the service boiler.
  • Page 93 “Technical” Programming Description Steam Boiler within approximately one minute of the • This procedure is recommended in case temperature reaching 140°C, disable the machine should remain inactive for the function and replace the valve. more than 8 hours and in any case at •...
  • Page 94 “Technical” Programming Description Steam Boiler Steam Boiler Settings Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. Exit To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is Menu displayed.
  • Page 95 “Technical” Programming Description Steam Boiler • The parameter “Level Sensit.” allows the • The black connection cable corresponds technician to select the probe sensitivity to the working level probe. for steam boiler filling according to water • The red connection cable corresponds to hardness.
  • Page 96 “Technical” Programming Description Steam Boiler • The parameter “Level Sensit.” allows the • The black connection cable corresponds technician to select the probe sensitivity to the working level probe. for steam boiler filling according to water • The red connection cable corresponds to hardness.

  • Page 97: Pre-Infusion Or Pre-Brewing

    “Technical” Programming Description Pre-Infusion or Pre-Brewing • This parameter allows the operator to pre-brewing cycle; during this time the program the time of pre-brewing of pump is active. Once the pre-brewing water with the coffee. Each group can cycle is over, the normal brewing cycle have a different programming.

  • Page 98: Crono Function

    “Technical” Programming Description Crono Function • When enabled, this parameter displays a • If enabled, the Chrono function is timer that times each shot. permanently displayed during brewing, • The timer is reset each time a button on while during wait state it alternates with the keypad is pressed.

  • Page 99: Clock Adjust

    “Technical” Programming Description Clock Adjust • This parameter allows the user to set the • There are 4 changeable values within time of day and the day of the week. this parameter: • This parameter is used to display time •...

  • Page 100: Cup Warmer

    “Technical” Programming Description Cup Warmer • This parameter allows the technician • This function is displayed only on the to enable or disable the cups heating models of espresso machine equipped function. with this accessory. • This parameter allows the technician •...
  • Page 101 “Technical” Programming Description Cup Warmer • This parameter allows the technician • This function is displayed only on the to enable or disable the cups heating models of espresso machine equipped function. with this accessory. • This parameter allows the technician •...

  • Page 102: Auto On/Off

    “Technical” Programming Description Auto ON/OFF • This parameter allows the technician to • This feature also allows the espresso program the espresso machine to turn on machine to remain in the off condition at a preset time and turn off at a preset for one repeating closed day.
  • Page 103 “Technical” Programming Description Auto ON/OFF • This parameter allows the technician to • This feature also allows the espresso program the espresso machine to turn on machine to remain in the off condition at a preset time and turn off at a preset for one repeating closed day.

  • Page 104: Eco Mode

    “Technical” Programming Description ECO Mode • This parameter allows the technician to • It is possible to set this parameter also set up a temperature to be maintained during the normal operation of the in case of a temporary non utilization of machine by pressing T1 and T2 at the the espresso machine.
  • Page 105 “Technical” Programming Description ECO Mode • This parameter allows the technician to • It is possible to set this parameter also set up a temperature to be maintained during the normal operation of the in case of a temporary non utilization of machine by pressing T1 and T2 at the the espresso machine.

  • Page 106: Coffee Dose Counter

    “Technical” Programming Description Coffee Dose Counter • This parameter allows the technician • This parameter displays different values: to review the total doses dispensed for • Total coffee doses; each button. • Coffee doses for each button; • Tea doses. Coffee Dose Counter Display...
  • Page 107 “Technical” Programming Description Coffee Dose Counter • This parameter allows the technician • This parameter displays different values: to review the total doses dispensed for • Total coffee doses; each button. • Coffee doses for each button; • Tea doses. Coffee Dose Counter Display...

  • Page 108: Filter Alarm

    “Technical” Programming Description Filter Alarm • This parameter enables the technician • A value of 0 (zero) disables the filter to program an alarm that will alert the alarm parameter. user about the need for maintenance or • This feature can be enabled or disabled. replacement of the water filter.
  • Page 109 “Technical” Programming Description Filter Alarm • This parameter allows the technician • A value of 0 (zero) disables the filter to preprogram an alarm that notifies alarm parameter. the user when the water filter requires • This feature can be enabled or disabled. service or replacement.

  • Page 110: Reset

    “Technical” Programming Description Reset • This parameter allows the technician to • It is possible to reset the settings you reset all the values returning to initial made in the “Barista” programming or factory settings. the settings you made in the “Technical” programming.

  • Page 111: Update Firmware

    “Technical” Programming Description Update Firmware • This parameter allows the technician to update the control unit of the espresso machine via a USB Pendrive. Update Firmware Display Operating Procedure Enter Password After accessing the “Technical” programming menu and entering the password, use the buttons T1 ****** until the following screen is displayed.

  • Page 112: Exit Menu

    “Technical” Programming Description Exit Menu • This parameter allows the technician to exit the “Technical” programming and return to the normal use of the espresso machine. Exit Menu Display Operating Procedure Exit Press the T3 button to exit the “Technical” programming and return to the normal use of the espresso Menu machine.

  • Page 113: Troubleshooting

    Troubleshooting • This espresso machine is equipped with several feedback mechanisms that alert the operator when an unusual condition occurs. Additionally the espresso machine will warn the operator when certain parameters fall below or above the programmed point. These errors and warnings will appear as a message in the display. •...
  • Page 114 Message Description Message Solution When the flowmeter alarm is displayed, push a button to turn off the alarm. This problem is a result of water This message is displayed when the CPU does not Flow Meter 1 not flowing through the flow meter. This can be caused by the coffee packed too tightly, a blockage in the No Pulse receive the appropriate signal from the flowmeter.

Table of Contents

Save PDF