Table of Contents
Advertisement
FCC Part 15 C Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
INDUSTRY CANADA NOTICE: CANADA ONLY.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
This product meets the applicable Innovation, Science and Economic Development Canada technical
specifications.
Ce produit répond aux spécifications techniques pertinentes d'Innovation, Science et Développement
économique applicables.
WARNING!
CHOKING HAZARD - Small parts.
Not suitable for children under 3 years.
Conforms to safety requirements of ASTM, CPSIA, RSS210 and FCC.
©2019 Rooftop Brands™ All rights reserved
www.propelrc.com
13
Indoor / Outdoor Wireless Quadrocopter
WARNING: Never leave product charging unattended for extended periods of
time. Always disconnect X20 from charger immediately after the X20 is fully
charged. Please refer to enclosed safety instructions.
X20
2.4G Wireless Controller
Made in China
X20
INSTRUCTION BOOKLET
PACKAGE CONTAINS:
USB Charging Cord
Spare Parts
Colors and styles may vary slightly.
Instruction Booklet
PROPEL
Advertisement
Table of Contents
Related Manuals for Propel Trampolines X20
Summary of Contents for Propel Trampolines X20
- Page 1 Ce produit répond aux spécifications techniques pertinentes d'Innovation, Science et Développement économique applicables. WARNING: Never leave product charging unattended for extended periods of time. Always disconnect X20 from charger immediately after the X20 is fully charged. Please refer to enclosed safety instructions. PACKAGE CONTAINS: WARNING! CHOKING HAZARD - Small parts.
-
Page 2: Table Of Contents
Arrow Mark Thank you for purchasing the 2.4 G Indoor /Outdoor X20. Please read this instruction booklet as it contains valuable information on how to properly fly and care for your X20. IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE! -
Page 3: Preparing For Flight
REMOTE DIAGRAM On/Off Switch 2. Turn ON the X20 and set it down on a flat surface. The LED indicator lights of the X20should begin to flash rapidly. 3. Turn ON the remote, you will hear one short beep. The X20’s LED lights should now flash slowly. -
Page 4: Now You Are Ready To Fly
NOW YOU ARE READY TO FLY! UNDERSTANDING TRIM ADJUSTMENTS If you have successfully synced your X20 to your controller as explained on page 4 you are now ready to fly. Forward/Backward Trim Before beginning to fly your drone you should familiarize yourself with how to start and stop the rotors, �•... -
Page 5: 3/4 Channel Select
To change to 3 channel mode: PRESS the Direction Control stick vertically down then release, you will hear 3 short beeps indicating the X20 now is set to 3CH mode. Move the Direction Control left and the X20 will Move the Direction Control right and the X20 To change back to 4 Channel mode: bank to the left. -
Page 6: Calibrating The X20
Stand away from the X20 to reduce the risk of getting into the flight path. Warn spectators that you will be flying your X20 so that they are aware of its position. Before flight, inspect the rotor blades to make certain of flying, you may need to calibrate the internal that the blades are securely fastened to the X20. -
Page 7: Limited 90-Day Warranty
Limited 90-Day Warranty NORTH AMERICA ROOFTOP BRANDS warrants to the original consumer that this product is free from any electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If any such defect is discovered within the warranty period, ROOFTOP BRANDS will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and insured to our warranty center.
Need help?
Do you have a question about the X20 and is the answer not in the manual?
Questions and answers