Related Manuals for Solgaz GPC-3
Summary of Contents for Solgaz GPC-3
- Page 1 Sp. z o.o. e- mail biuro@solgaz.com.pl Assembly and operating instructions OF CERAMIC GAS HOB for kitchen furniture arrangement GPC – 3, GPC-3-T...
-
Page 2: Dear Customer
Have fun with preparing your perfect tasty meals. Yours sincerely,SOLGAZ The ceramic gas hob must be connected to a gas source by an authorized person(certified installer) Dear Sir, Dear Madam,We guarantee that your new gas-fired heating panel will operate correctly. -
Page 3: Table Of Contents
1.2. Technical data of the GPC-3 hob ........ -
Page 4: Application Of The Hob
1.1. Application of the hob.The GPC-3 type plate is a ceramic hob with 3 gas burners located underneath. This is the newest generation of gas hobs where special gas burners controlled by an electronic system process heat generated through gas combustion into infrared radiation. Radiation infiltrating the ceramic plate heats the dishes positioned above the hot fields. -
Page 5: Requirements For Hob Installation
Fig. 1 1 – ceramic plate, 2 – hot field A ø120, 3 – hot field C ø90, 4 – hot field D ø180, 5 hot aera 6 – combustion gas outlet, 7 – controller,, 8 – gas inlet, 9 – power supply socket 10 – power adapter Fig. -
Page 6: Requirements For Rooms
contact your gas supplier. Proceeding in such case is described in details under 5.2 of the instruction. 2.1. Requirements for rooms. The rooms designated for installing the hob should be dry and airy, with efficient natural ventilation. 2.2. Installation and assembly in furniture All activities related to the assembly and connection of the stove to the gas and electric systems must be performed by an authorized installation technician. - Page 7 Fig. 3. Installation side view front view Fig. 4. Assembly 1-VENTILATION AIR INLET 2- VENTILATION AIR INLET WITH GRID Fig. 5. Hob with oven arrangement 1 – VENTILATION AIR INLET IN THE BOTTOM PART OF THE SHELF; 2 – VENTILATION AIR INLET WITH MESH;...
-
Page 8: Gas Installation
The control system of the hob is supplied with 12 V direct current through a power supply. In order to assure correct and safe operation of GPC-3 hobs, it is necessary to provide an electric socket (230 V/50 Hz) close to the location of the stove in order to connect the hob’s power supply. -
Page 9: Switching On And Setting The Heating Power Of Burners
after a while the electronic system of the hob goes into a standby mode, the indicators are switched off and the main switch sensor is turned on again. TIMER function, touch the burner selection fields twice (Fig.2, no 5,6 or 7), touch “+” and “-“ to select time in minutes (from 1 to 99 min.), the burner stops automatically after selected time 3.2. -
Page 10: Switching Off The Burners
The hob operating status with reheating is a transitory condition for rapid achievement of target temperature of the active hot field, up to the heating power set. It is signaled by the decimal point lighting up next to the active burner’s digital indicator (5,6,7, fig2). If any level of heating power is set for the given hot field, the controller display will show a number corresponding to the power setting. -
Page 11: Utilization Of Combustion Gas Heat
!!! 3.8. Utilization of combustion gas heat. The GPC-3 ceramic gas plate has additional hot field – no 5, which is shown on fig. 1, using the heat of combustion gas leaving the burner to the outlet grate situated in the rear part of hob. -
Page 12: Cleaning The Ceramic Plate
power setting.If you do not change the heating power level for a long time, then the corresponding hot field is automatically shut down and the residual heat indicator “H” is activated. However, you can switch on and use the individual fields at any time, according to operating instructions. These relationships are given in Table 2. -
Page 13: Instructions For The Installer
- checking the technical condition of the aforementioned systems, - notifying the building administrator of any doubt concerning the technical condition of these installations. FOR THE INSTALLER 5. INSTRUCTIONS 5.1. Activities related to hob installation, connection to gas and electrical systems and adjusting hob burners to a different type of gas can only be carried out by a properly trained and certified worker. -
Page 14: Maintenance And Inspection Of Hob Components
5.3. Maintenance and inspection of hob components. If the hob is operated in accordance with these instructions, cleaned and maintained according to the description presented in sub-clause 4.1, - then a hob that works properly does not require inspection. 6. HANDLING DEFECTS – error signaling Please read the following guidelines before calling the manufacturer’s service technician: - The reheating pad heats up but does not glow during operation of the burner pad. - Page 15 The following will be delivered together with your hob: - Power supply adapter. Our service center’s phone no.: +48 074 856 52 88 serwis@solgaz.com.pl correspondence address: SOLGAZ Sp. z o. o. 58-124 Marcinowice ul. Spoldzielcza 3 Poland ------------------------------------------------------------------------------------------------------ TYPE: GPC – 3 SERIAL NUMBER…………………………………….
Need help?
Do you have a question about the GPC-3 and is the answer not in the manual?
Questions and answers