WattBox WB-800VPS-IPVM-12 Quick Start Manual
  1. Manuals
  2. Brands
  3. WattBox Manuals
  4. Power distribution unit
  5. WB-800VPS-IPVM-12
  6. Quick start manual

WattBox WB-800VPS-IPVM-12 Quick Start Manual

Hide thumbs

Advertisement

Table of Contents

™
WB-800VPS-IPVM-12
WB-800VPS-IPVM-18
QUICK START GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WB-800VPS-IPVM-12 and is the answer not in the manual?

Questions and answers

Related Manuals for WattBox WB-800VPS-IPVM-12

Summary of Contents for WattBox WB-800VPS-IPVM-12

  • Page 1 ™ WB-800VPS-IPVM-12 WB-800VPS-IPVM-18 QUICK START GUIDE...

  • Page 2: Front Panel

    A. Power Inlet: Detachable power cord outlet for 3 prong IEC power cord. B. Circuit Breaker Reset Button: Press this button to restart the WattBox after an overload. C. AC Power switch: Press to manually toggle the outlets on or off. This glows with an amber light when the unit is powered.
  • Page 3 Controllable Outlets: All outlets are switchable (IP controlled). K. Power Indicators: These illuminate when power to the matching outlet is on. Page 3...

  • Page 4: Package Contents

    • Power strip • Removable power cord • Screws • Nuts • Mounting clips (2 × for WB-800VPS-IPVM-12, (2 × for WB-800VPS-IPVM-12, (2 × for WB-800VPS-IPVM-12, 3 × for WB-800VPS-IPVM-18) 3 × for WB-800VPS-IPVM-18) 3 × for WB-800VPS-IPVM-18) Page 4...

  • Page 5: Rack Mount Installation

    RACK-MOUNT INSTALLATION This can be mounted vertically on the outside of one leg of a rack. Install the Clips Using the nuts and screws provided, install the mounting brackets (with the clips oriented as shown at right) on the outside of one rack rail.

  • Page 6: Wall Mount Installation

    WALL-MOUNT INSTALLATION This unit can also be mounted on a wall, either vertically or horizontally. Install the Clips Draw a level line where you want to mount the power strip Using wall anchors or other appropriate hardware (not provided), attach the mounting brackets (with the clips oriented as shown) centered on the level line, so that the clips are 4"–6"...

  • Page 7: Connections And Setup

    CONNECTIONS AND SETUP If attaching an IP-enabled WattBox UPS to the power strip, plug the cable from the UPS into the UPS link port (page 2, item H). Caution: The UPS link must be connected before applying power to the VPS.
  • Page 8 CLAIMING THE WATTBOX ON OVRC The WB-800 has many powerful features that are accessed through OvrC, our award-winning remote management tool. If you are not familiar with OvrC, visit OvrC.com. To find training for OvrC, log in to SnapAV.com, click on the Training tab, and then launch Snap University.

  • Page 9: Led Indicators

    Green (Solid) All sites / IP addresses are communicating with the WattBox Green (Flashing) At least one (not all) sites / IP addresses are communicating with the WattBox None of the sites / IP addresses are communicating with the WattBox.

  • Page 10: Troubleshooting

    Possible Cause Remedy Wattbox is not Wattbox is not turned on. If the WattBox power button does not show amber, press it. receiving power No power is being supplied. Make sure the AC power plug is plugged into a properly (the System grounded 120V (nominal) wall outlet.

  • Page 11: Important Safety Instructions

    CAUTION – Potential Injury Do not use this product with extension cords, multioutlet power strips, multioutlet extenders, or UPS devices (other than a WattBox UPS). The power capacity of these accessories can be overloaded by this product and may result in a risk of fire, or property damage.
  • Page 12 WARNING – Liquid: Avoiding Electrical Shocks Do not operate the WattBox if liquid of any kind is spilled onto or inside the unit. Do not operate it near rain or water, even water that is contained (e.g., bathtub or sink).

  • Page 13: Fcc Warning

    FCC WARNING WARNING!! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation.

  • Page 14: Warranty

    WARRANTY 5-Year Limited Warranty This SnapAV® product has a 5-Year Limited Product Warranty and a 5-Year Network Connectivity Warranty. The 5-Year Limited Product Warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use.
  • Page 15 telephone, or lightning surge while connected to a properly installed SnapAV surge protector. SnapAV must determine that the surge protector shows signs of surge damage or is operating outside of design specifications, relative to its surge protection capability, and under all of the circumstances failed to protect your connected equipment. This policy is subject to the conditions below: PROOF OF PURCHASE REQUIRED SnapAV’s connected equipment policy extends to the original purchaser of the SnapAV product only and is non-transferable.

  • Page 16: Logging Into The Web Interface

    You need to enter the username and password to access the web interface. The default entries are below; be sure to change these to maintain proper security (and log them below). Default Custom Username wattbox Password wattbox Version 181016-1123 Page 16...

This manual is also suitable for:

Wb-800vps-ipvm-18

Table of Contents