Advertisement
Quick Links
Table of Contents
Safety Instructions & Warnings
What's Included & Installation
eFlux Wave Pump Installation
Cable Connections
Programming Guide
Safety Warnings & Warranty
Safety Instructions & Warnings
IMPORTANT: Please refer to additional safety warnings on last page.
- eFlux wave pumps create a tremendous amount of water flow. Do not install pump where the
strong current can harm corals or animals.
- Do not install pump too close to the sand bed where it will not stir/suck the sand.
- Pumps can also produce powerful waves in both wave and surge mode. Ensure your aquarium is
designed for wave pumps and ensure pumps are mounted low enough not to push water out of the
aquarium.
- Magnet mounting assembly is very powerful. Be cautious not to cause injury to fingers.
- Keep out of reach of children.
- Never place magnets or pump near sensitive electronics, sharp objects or attractive surfaces.
- Never run wave pump dry or out of water.
- Always place spacer between magnets when not in use.
- Always unplug with dry hands for any maintenance or service.
- eFlux wave pumps are 24VDC. Ensure one 24VDC UL® transformer is used per wave pump.
- Ensure 24VDC UL® transformer is plugged into a GFCI approved outlet with a drip loop.
- Turn controller OFF and disconnect pump from power before performing any service
- Ensure eFlux wave pumps and any accessories all have a drip loop installed before plugging into
the wave pump manifold HUB as shown below.
Use caution when
installing magnets
Ensure pump location
will not spill water from
wave motion
1
2
3
4
5-9
10
Ensure correct voltage power
supply for each component
P3
P2
P1
Drip
Wave Pump
Loop
Manifold HUB
Ensure use of drip
loop for all cables
SAVE THESE INSTRUCTIONS
For purchasing our eFlux Wave Pump Kit.
Please read all instructions before
getting in the LOOP!
24VDC
Power Supply
24VDC
Power Supply
Wave Pump
Drip
LCK P/S SRE SUR PUL FRE FLO
LED Display
Loop
Page 1
eFlux Wave Pump Kit
Thank You!
Use only with GFCI
Protected AC Outlet
AC Power
GFCI Outlet
Ensure use of drip
loop for all cables
Advertisement
Related Manuals for Current eFlux
Summary of Contents for Current eFlux
- Page 1 Safety Instructions & Warnings IMPORTANT: Please refer to additional safety warnings on last page. - eFlux wave pumps create a tremendous amount of water flow. Do not install pump where the strong current can harm corals or animals. - Do not install pump too close to the sand bed where it will not stir/suck the sand.
- Page 2 Wave Pump Kit Additional Help For additional installation instructions & videos, please visit our website at www.current-usa.com What’s Included Each eFlux Wave Pump Kit includes: Item Description Quantity eFlux DC Wave Pump Note: Magnet Swivel Bracket Assembly (pre-installed) 24V DC Transformer, UL® Listed...
- Page 3 6”-10” away from where the wave pump manifold HUB will be mounted. Step 6. Using included wood mounting screws, mount the eFlux wave pump HUB mounting bracket (E) and eFlux pump LED display bracket (G) to stand. Slide wave pump manifold HUB (D) and pump LED display (F) into each bracket.
-
Page 4: Specifications
Connect LED Display micro USB cable into Port#2 b. Connect IR Sensor micro USB cable into Port#1 c. Connect eFlux Wave Pump into P1 Pump Connection d. Connect 24V DC cable into P1 Power DC input Step 10. Plug 24V DC transformer into GFCI outlet. - Page 5 Wave Pump Kit Programming Guide Remote Control Overview Main On/Off Pump 1, Primary Wave Pump Pump 2, Secondary Wave Pump Pump 3, Flow/Stream Mode Only Primary/Secondary Pump FEED STREAM FEED Mode FEED Lock/Unlock Key SURGE FREQ LOCK FLOW Stream / Steady Flow Mode...
- Page 6 Wave Pump Kit Programming Guide Step 1: Turning pumps ON/OFF Press the Main ON/OFF key to turn all of the pumps and pump display ON or OFF. When pumps are on, LEDs on display will illuminate. If all pumps are turned off, all LEDs on display will be off.
- Page 7 .5s .7s Pump ON .5s .7s Pump OFF Choosing flow modes Every aquarium is different and eFlux wave pumps provide multiple modes of flow for a wide variety of applications. SURGE/GYRE MODE WAVE/PULSE MODE STREAM/STEADY MODE Steady, constant flow stream (adjustable)
- Page 8 Wave Pump Kit Programming Guide Step 5A: Designate pump to program (1, 2, or 3) Press the pump you pick to program by " pressing the designated pump key on the wireless remote. Pump icon will illuminate on LED display.
- Page 9 Programming Guid Primary/Secondary Pump Syncing (GYRE) A pump group consists of one Primary pump and at least one Secondary pump. The eFlux Wave Pump manifold HUB automatically designates Pump 1 as a Primary pump. Pump 2 can be designated as a Primary pump (controlled independently), or as a Secondary pump (runs oppo- site of Primary pump).
- Page 10 Loop Drip Loop Current-USA One Year Limited Warranty This product MUST be purchased from an authorized Current-USA reseller. Visit our website for a list of unauthorized resellers. Current USA, Inc. warrants this product against defects in materials and worksmanship for ONE (1) YEAR from the date of original retail purchase and is none transferable.
Need help?
Do you have a question about the eFlux and is the answer not in the manual?
Questions and answers