Hub Installation - Norman SmartDial User Manual

Function
NO.
Setup Louver Bottom
11
Position (Down Limit)
Delete/Clear
12
louver Bottom Position
Norman Hub
®
˙Preparation Notes
1. Finish shutter assignment of each room to corresponding Remote first.
2. Each room needs a Repeater installed. If the signal needs to pass to a different floor, you will need Repeater installed
around the stairs as well.
˙Hub Installation
1. Connect the Micro USB to the Norman
2. Support two network connection settings, please choose one of them.
► Option 1 :
Connect Norman
1) Connect one end of the Ethernet route to the LAN port of the AP router and one end to the Ethernet port
of the Norman
2) The mobile phone is connected to the home AP router WiFi.
3) Open the App and select Connect to Hub to connect to the Norman
► Option 2 :
Connect Norman
1) The Norman
(the last six codes of the MAC is the same as the label number on the Hub) through the mobile phone, and can
be connected.
2) Norman® Hub WiFi password:
3) Open the Norman
instructions to connect the Norman® Hub to your home WiFi.
4) When the Norman
The SSID of NORMANHUB_OOOOOO will not be visible at this time. The phone will automatically switch back to the
commonly used and connected AP router (basically the home AP router)
5) Open the App and select Connect to Hub to connect to the Norman
˙Join Remote to Hub Network
®
1. Power on Norman
2. Once booted up, LED will light on in white.
3. Initiate Remote Reset Mode
4. Press Hub button once.
5. LED of Remote will light for 3 seconds once network sync completes.
6. Press Remote button (
7. Do Manual Search for adding shutters.
1) Hold Norman
The LED will turn blue.
2) Press once within 5 seconds right after step 1).
3) LED will blink in blue and white as it searches
shutters status.
4) Once it finishes searching, LED will light on
in white to indicate normal status.
1. Select the group(s) you want to setup bottom position, and hold down for Tilt Upward button
( ) 1 second.
2. Move the louvers to bottom position by hand.
up to down. If direction was reversed, please start over.]
Reset Mode.
3. Initiate Remote
4. Select the group(s) you want to setup bottom position.
5. Press Tilt Downward button (
3 times. [NOTE: Tilt Downward button won't work if no groups are selected.]
6. Louvers move up and down once.
Reset Mode.
7. Exit Remote
Reset Mode.
1. Initiate Remote
2. Select the group(s) you want to delete bottom position.
3. Press Tilt Upward button (
[NOTE: Tilt Upward button won't work if no groups are selected.]
4. Louvers move up and down twice.
5. Press Remote Reset button for 1 second to exit Remote
®
Hub and connect it to the power source.
®
Hub and home AP router via Ethernet route.
®
Hub.
®
Hub and home AP router via WiFi.
® Hub is AP Mode without any network connection. You can find the SSID of NORMANHUB_OOOOOO
norman1974
®
App and select Connect to Hub > Menu > Hub Info > Home AP Settings and follow the
® Hub is connected to the home AP router via WiFi, it will automatically switch to Station Mode.
Hub, orange LED will blink while it boots up.
in close proximity to the Hub. (You can do multiple Remotes joining at same time)
) for updating data to all shutters(Motor Modules).
[Same as Norman
® Hub button for 3 seconds to initiate
Description
[NOTE: The direction of operation MUST be from
), group LED will turn off and middle buttons will blink
), group LED will turn off and middle buttons will blink 3 times.
Reset
®
Hub.
®
Hub.
®
Hub Function No.1]
User Setting mode.
RS-232 Port
Ethernet Port
Mode.
Hub Button
Power Input
(Micro-USB Port)
Page 05/09