Summary of Contents for Armstrong SAGE UMT
- Page 1 SAGE UMT Universal Mobile ™ Tester Operating Manual Please read and save these instructions 263-EN...
-
Page 2: Table Of Contents
Controls and Connections . . . . . . . . . . . . . . . . 7 Pairing SAGE UMT with SAGE App . -
Page 3: System Overview
The SAGE ® Universal Mobile Tester (SAGE UMT ) is a wireless hand- ™ held steam trap testing tool. The SAGE UMT utilizes innovative wireless ™ features combined with state of the art temperature and acoustics sensing technology. Features include: •... -
Page 4: Safety
Only designated, qualified, and competent personnel should operate, maintain, and service this device in accordance with the directions in this product instruction manual. The SAGE UMT is NOT serviceable by non-Armstrong personnel. ™ Improper set-up, operation, or maintenance may void the product warranty. - Page 5 SAGE UMT . These actions could result in physical damage to the on-board, Li-ion, battery ™ pack. A damaged battery pack can cause an explosion or fire to start within the SAGE UMT ™ • Remove the battery pack •...
- Page 6 Continued BURN HAZARD! Hot Probe Tip May Cause Burn . Frequent or prolonged contact of the metal probe tip of the SAGE UMT with high temperature ™ surfaces, e.g. active steam traps and steam piping, will heat the probe tip. Avoid touching the probe tip to bare skin during or immediately after SAGE UMT usage.
-
Page 7: Controls And Connections
Controls and Connections SAGE UMT controls, connections and indicators: ™ Temperature Sensor Acoustic (not pictured) Sensor RFID Indicator: System Power Blinks when On/Off button scanning. (4 second hold) Steady on after tag is scanned, scanning paused for Bluetooth indicator: ®... -
Page 8: Pairing Sage Umt ™ With Sage ® App
Pairing SAGE UMT with ™ SAGE ® SAGE Username and Password Required ® In order to pair the SAGE UMT with phone or tablet ™ app, the user must have an active SAGE account ® with specific SAGE username and password. -
Page 9: Rfid System
SAGE RFID Overview ® The left side of the SAGE UMT contains an RFID reader. The ™ RFID reader enables the user to quickly scan an RFID tag which will automatically bring up the record in the SAGE app of the steam trap to be ®... -
Page 10: Database
If using RFID tags - scan tag to assign to the steam trap record. Install the new SAGE RFID tag in a location near the steam trap where it ® can be physically touched by the left side of the SAGE UMT . For resurveys, ™ scan the SAGE... -
Page 11: Using Rfid Tag
It is important to maintain about 5 pounds (2.25 kgf) of pressure throughout the test. Start steam trap test by pressing the "Start Test" button on the SAGE UMT , or for remote 1 2 3 4 5 6 7 8 9 ™... -
Page 12: Without Rfid Tag
(2.25 kgf) of pressure throughout the test. 1 2 3 4 5 6 7 8 9 Start steam trap test by pressing the "Start Test" button on the SAGE UMT , or for remote ™ activation, press the start test button in the SAGE app . -
Page 13: Sage Umt
LOCKED UNLOCKED Pole Connection The base of the SAGE UMT features a ™ threaded socket. For testing of steam traps that are out of convenient reach, connect a standard non-conductive extension pole. The Bluetooth ®... -
Page 14: Troubleshooting
™ inside the charging port. Confirm power adapter is plugged into a known good outlet then press barrel plug into charging port. Let device charge for 30 minutes if no lights come on contact Armstrong or your local Representative. Continued on next page Designs, materials, weights and performance ratings are approximate and subject to change without notice. - Page 15 Q: SAGE UMT is not reading RFID tag. ™ A: Confirm you are holding RFID tag to the center of the left side of the SAGE UMT . If available test ™ with a known good tag to see if RFID tag has malfunctioned. Confirm RFID light is flashing at the top of the display, if RFID indicator is solid wait 10 seconds for scanning to be active again.
-
Page 16: Proper Probe Touch Points
Proper Probe Touch Points Inverted Bucket Float & Thermostatic Thermal element Outlet pipe (for process traps with heavy loads) Designs, materials, weights and performance ratings are approximate and subject to change without notice. Software updates - 16 - may cause the app to look and or behave differently, visit armstronginternational.com for up-to-date information. -
Page 17: Proper Probe Touch Points
Proper Probe Touch Points Thermodynamic/Disc Traps Thermostatic, Bimetallic Traps on connector blocks or trap valve stations Designs, materials, weights and performance ratings are approximate and subject to change without notice. Software updates - 17 - may cause the app to look and or behave differently, visit armstronginternational.com for up-to-date information. -
Page 18: Product Specifications
Product Specifications and Certifications EMC Compliance Maximum Operating Conditions (North America) Minimum steam 2 psig (0.14 barg) pressure FCC Part 15 Subpart B, Maximum steam 3200 psig (221 barg) Sec.15.107a & 15.109a (Class B pressure Digital Device); ICES-003, Issue 6 Temperature -4°F to 140°F (-20°C to Class B... - Page 19 Notes: Designs, materials, weights and performance ratings are approximate and subject to change without notice. Software updates - 19 - may cause the app to look and or behave differently, visit armstronginternational.com for up-to-date information.
-
Page 20: Limited Warranty And Remedy
Armstrong products, notice of any warranty or other claim relating to the products must be given in writing to Armstrong: (i) within 30 days of last day of the applicable warranty period, or (ii) within 30 days of the date of the manifestation of the condition or occurrence giving rise to the claim, whichever is earlier.
Need help?
Do you have a question about the SAGE UMT and is the answer not in the manual?
Questions and answers