NorthStar NSC 11 ED Installation, Operation, Maintenance & Repair Parts page 18

RNORTHSTAR ......
ELECTRONIC DEMAND
NOTE: SEE PAGE 10 TO SET THE TIMER TO THE CORRECT TIME OF DAY, WATER HARDNESS NUM-
BER, AND RECHARGE START TIME.
1250$/ 23(5$7,21 7,0(5 ',63/$<6                                        
During normal operation, the pres-
ent time of day, (24 hour mode)
show in the time display area.
When the demand computer de-
termines a regeneration is needed, RECHARGE
TONIGHT begins to flash in the display, along with
feature: 237,21$/ 5(&+$5*( &21752/6                                     
Sometimes, a manually started regeneration (recharge) may be desired, or needed. Two examples are:
... You have used more water than usual (house guests, extra washing, etc.) and you may run out of soft water
before the next regeneration.
... You did not refill the storage tank with salt before it was all gone.
Use one of the following features to start a regeneration immediately, or at the next preset regeneration start
time.
RECHARGE NOW
Press and KROG in the TOUCH - HOLD button until
RECHARGE NOW starts to flash in the time display
area. The softener begins an immediate regenera-
tion, and when over in about two hours, you will have
a new supply of soft water. Once started, you cannot
cancel this regeneration.
9$&$7,21 127(                                                                             
North Star Demand water softeners regenerate only while water is used and softening capacity must be re-
stored. For this reason, the softener will not regenerate when you are away from home for extended periods.
feature: 352*5$0 0(025<                                                   
If electrical power to the softener is interrupted, the
time display is blank, but the timer keeps correct
time for about 6 hours. When power is restored, you
have to reset the present time only if the display is
flashing. All other settings are maintained and nev-
er require resetting unless a change is desired.
features:
12-24 hour clock / Set Backwash and Fast rins time / Max days between recharge.
Press and hold the SELECT button for 3 seconds:
The Turbine count/ switch position display is shown
(See page 20). Press the SELECT button again, the
recharge ( max days between) is shown. The default
is Automatic (the algorithim will determine when to
recharge). Use the UP/DOWN buttons to change
between 1 and 7 days. With this setting the unit will
never go past number of days set for a recharge, but
AUTOMATIC WATER CONDITIONER
TIMER FEATURES, AND SERVICE
the present time. RECHARGE
.
30
.
TONIGHT flashes until the next
regeneration start time, then
changes to RECHARGE NOW,
which flashes until the regeneration is over.
.
30
.
RECHARGE TONIGHT
5(&+$5*( 12:
Touch (do not hold) the TOUCH - HOLD button, and
RECHARGE TONIGHT flashes in the time display
area. A regeneration will occur at the next preset re-
generation start time. If you decide to cancel this re-
generation, touch the same button once more.
If the time LV flashing after a long power outage, the
softener continues to work as it should to provide
you with soft water. However, regenerations may
occur at the wrong time of day until you reset the tim-
er to the correct time of day, page 10.
could recharge before. Press the SELECT button,
12-24 hour clock is displayed. Use the UP/DOWN
buttons to chose between 12 hour (AM&PM)
hour format. Press the SELECT button again and the
BACKWASH ( b) will be displayed ( in min). Press the
SELECT button again and the FAST RINSE (r) (in min) will
be displayed.Use the UP/Down buttons to change the times.
Press the SELECT button again to retun to the time display.
18
.
30
.
5(&+$5*( 721,*+7
.
30
.
5(&+$5*( 721,*+7
, or 24