Philips 32PFL3506/F7 Service Manual

32" lcd tv chassis pl11.0

Hide thumbs Also See for 32PFL3506/F7:

Quick start manual (6 pages)

Specifications (3 pages)

User manual (15 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Philips 32PFL3506/F7

Page 1: Service Manual
32” LCD TV chassis PL11.0 Service Manual Contents TYPE A 32PFL3506/F7 PHILIPS (Serial No.: DS1) 32PFL3506/F7 PHILIPS (Serial No.: XA1) 32PFL3000/F8 PHILIPS (Serial No.: XA1) TYPE B 32PFL3506/F7 PHILIPS (Serial No.: DS2) 32PFL3506/F7 PHILIPS (Serial No.: DS3) 32PFL3000/F8 PHILIPS (Serial No.: XA2) This service manual contains information of different types of models.
Page 2: Important Safety Notice
IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
Page 3: Table Of Contents
TABLE OF CONTENTS Specifications ................1-1 Important Safety Precautions .
Page 4: Specifications
SPECIFICATIONS < TUNER / NTSC > ANT. Input ---------------------- 75 Ω Unbal., F type Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBµ 2. Synchronizing Sens. CA.ch.31 dBµ CA.ch.87 dBµ < TUNER / ATSC > Description Condition Unit Nominal...
Page 5: Important Safety Precautions
IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Page 6 3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
Page 7 Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
Page 8 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.
Page 9: Standard Notes For Servicing
STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: Top View 1. Prepare the hot-air flat pack-IC desoldering Bottom View machine, then apply hot air to the Flat Pack-IC Input...
Page 10 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
Page 11 2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Page 12 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
Page 13: Cabinet Disassembly Instructions
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Step/ Fig. Loc. Part Removal Note This flowchart indicates the disassembly steps for the cabinet parts and the CBA in order to gain access to IR Sensor items to be serviced. When reassembling, follow the CL103A steps in reverse order.
Page 14 [2] Rear Assembly (L-1) (S-2) (L-1) (S-4) (S-2) (L-1) (L-1) (S-2) (S-2) (S-4) (S-3) (S-2) [1] Stand Assembly (S-1) Fig. D1 PL11.0-A_DC...
Page 15 [3] Inverter CBA [5] Power Supply CBA (S-7) (S-5) (S-6) [4] Jack CBA (S-7) Shield Box (S-9) (S-9) (S-8) Jack Holder [6] Digital Main CBA Unit Fig. D2 PL11.0-A_DC...
Page 16 [11] Front Cabinet [10] LCD Module Assembly (S-11) [9] Function CBA [8] IR Sensor CBA Function Knob Knob Frame [7] Speaker Speaker Holder [7] Speaker (S-10) Fig. D3 PL11.0-A_DC...
Page 17 TV Cable Wiring Diagram Jack Inverter CBA CN1102 Power Supply CBA CL701B CN201 CN1001 CN1101 CL701A CN602 CN1100 CN1901 CN302 CN1003 AC CORD CN301 CN801 CN802 CN101 To LCD Module Assembly To Speaker Digital Main CBA Unit Function TYPE A CN3702 TYPE B CN3006...
Page 18: Electrical Adjustment Instructions
ELECTRICAL ADJUSTMENT INSTRUCTIONS [32PFL3506/F7 (Serial No.: DS1, XA1), 32PFL3000/F8 (Serial No.: XA1)] General Note: “CBA” is abbreviation for How to set up the service mode: “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after 1. Turn the power on.
Page 19 1. Purity Check Mode 2. VCOM Adjustment This mode cycles through full-screen displays of red, Test Point Adj. Point green, blue, and white to check for non-active pixels. [CH + or -] Screen 1. Enter the Service mode. buttons 2. Each time the [7] button on the remote control unit M.
Page 20 The White Balance Adjustment should be 5. [CUTOFF] Press [1] button to select “COR” for Red Cutoff performed when replacing the LCD Panel adjustment. Press [3] button to select “COB” for or Digital Main CBA. Blue Cutoff adjustment. [DRIVE] 3. White Balance Adjustment Press [4] button to select “DR”...
Page 21 [32PFL3506/F7 (Serial No.: DS2, DS3), 32PFL3000/F8 (Serial No.: XA2)] General Note: “CBA” is abbreviation for How to set up the service mode: “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after 1. Turn the power on. replacing circuit components and certain mechanical parts.
Page 22 [7] button Black mode Color Analyzer [7] button Red mode 32PFL3506/F7 (Serial No.: DS2), 32PFL3000/F8 (Serial No.: XA2): 1. Set the color analyzer at the zero point calibration and bring the optical receptor pointing at the center of the LCD-Panel.
Page 23 The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal appears on the screen. (“Internal (Single)” performed when replacing the LCD Panel appears on the upper right of the screen as shown or Digital Main CBA. below.) 3.
Page 24: How To Initialize The Lcd Tv
To put the program back at the factory-default, initialize the LCD TV using the following procedure. [32PFL3506/F7 (Serial No.: DS1, XA1), 32PFL3000/F8 (Serial No.: XA1)] 1. Turn the power on.
Page 25: Firmware Renewal Mode
Downloading the firmware from Downloading... White Balance, etc. the USB storage device. Writing the downloaded firmware : 32PFL3506/F7 (Serial No.: DS2, DS3), Writing... in flash memory. 32PFL3000/F8 (Serial No.: XA2) Checking... Checking the new firmware.
Page 26: Troubleshooting
TROUBLESHOOTING [ Power Supply Section ] FLOW CHART NO.1 The power cannot be turned on. Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (C605, D601, D602, D603, D604, Q601, Q602, Q603, Q604, IC602, T601) Is the AL+33V line voltage normal?
Page 27 FLOW CHART NO.6 LCD+31.5V is not output. FLOW CHART NO.7 LCD+13V is not output. FLOW CHART NO.8 P-ON+7V is not output. PL11.0TR...
Page 28: Flow Chart No
FLOW CHART NO.9 P-ON+5V is not output. (LCD+13V is outputted normally.) Replace Q641. FLOW CHART NO.10 TUNER+5V is not output. (LCD+13V is outputted normally.) Replace Q640. FLOW CHART NO.11 AL+13V is not output. Is approximately +13V voltage supplied to the cathode of D641 and D642? FLOW CHART NO.12 P-ON+3V is not output.
Page 29 FLOW CHART NO.13 P-ON+3.3V is not output. FLOW CHART NO.14 P-ON+9V is not output. (LCD+13V is outputted normally.) Replace Q642. FLOW CHART NO.15 AL+3.3V is not output. FLOW CHART NO.16 LCD-5V is not output. Replace Q211. PL11.0TR...
Page 30 [ Video Signal Section ] FLOW CHART NO.1 The key operation is not functioning. Re-install the switches (SW101B, SW103B~SW107B) correctly or replace the poor switch. Check the switches (SW101B, SW103B~SW107B) and their periphery, and service it if defective. Replace Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit.
Page 31 FLOW CHART NO.4 Picture does not appear normally.(Tuner input) FLOW CHART NO.5 Picture does not appear normally.(S-Video input) Pin(6): S-VIDEO-C Pin(8): S-VIDEO-Y FLOW CHART NO.6 Picture does not appear normally.(Y/Pb/Pr input) Pin(15): VIDEO-Y Pin(17): VIDEO-Pb Pin(19): VIDEO-Pr PL11.0TR...
Page 32 [ Audio Signal Section ] FLOW CHART NO.1 Audio is not outputted normally.(Audio input) Check the line between Pin(2, 15) of IC771 and input terminal(JK753, JK754), and service it if defective. Pin(6) : AMP(L)-OUT Pin(8) : AMP(R)-OUT Pin(2) : AUDIO(L)-OUT Pin(4) : AUDIO(R)-OUT CN801: SP(L)
Page 33 FLOW CHART NO.2 Audio is not outputted normally.(Component Audio input) Check the line between Pin(4, 11) of IC771 and input terminal(JK741, JK742), and service it if defective. Pin(6) : AMP(L)-OUT Pin(8) : AMP(R)-OUT Pin(2) : AUDIO(L)-OUT Pin(4) : AUDIO(R)-OUT CN801: SP(L) Check SP801,SP802 and their periphery circuit, CN802: SP(R) and service it if defective.
Page 34 FLOW CHART NO.3 Audio is not outputted normally.(Tuner input) Check TU301 and their periphery circuit, and service it if defective. Pin(6) : AMP(L)-OUT Pin(8) : AMP(R)-OUT Pin(2) : AUDIO(L)-OUT Pin(4) : AUDIO(R)-OUT CN801: SP(L) Check SP801,SP802 and their periphery circuit, CN802: SP(R) and service it if defective.
Page 35: Block Diagrams [Type A]
BLOCK DIAGRAMS [TYPE A] 1. System Control Block Diagram PL11.0ABLS...
Page 36 2. Video Block Diagram PL11.0BALV...
Page 37 3. Audio Block Diagram PL11.0ABLA...
Page 38 4. Digital Signal Process Block Diagram PL11.0ABLD...
Page 39 5. Inverter Block Diagram PL11.0ABLINV...
Page 40 6. Power Supply Block Diagram PL11.0ABLP...
Page 41: Type B]
[TYPE B] 1. System Control Block Diagram PL11.0BBLS...
Page 42 2. Video Block Diagram PL11.0BBLV...
Page 43 3. Audio Block Diagram PL11.0BBLA...
Page 44 4. Digital Signal Process Block Diagram PL11.0BBLD 9-10...
Page 45 5. Inverter Block Diagram 9-11 PL11.0BBLINV...
Page 46 6. Power Supply Block Diagram 9-12 PL11.0BBLP...
Page 47: Schematic Diagrams / Cba And Test Points
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 48 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
Page 49 Power Supply 1 Schematic Diagram CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply hot GND as a common terminal.
Page 50 Power Supply 2 Schematic Diagram *Either TU301 is used for Power Supply CBA. TU301 TUNER UNIT TU301 TUNER UNIT CONTINUE POWER 1 AL+33V TUNER+5V 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 1 2 3 4 5 6 7 8 9 10 CONTINUE...
Page 51 Power Supply 3 & Jack Schematic Diagram POWER SUPPLY CBA BC841 BEAD C843 C844 0.01 10/50V R847 R846 4.7K C842 Q841 KTC3198-Y-AT/P R848 CONTINUE C841 R842 R844 4.7K (BUFFER) POWER 1 JK841 DIGITAL P-ON+3.3V AUDIO-OUT (COAXIAL) R841 R843 R845 P-ON+9V OPEN OPEN C771...
Page 52 Power Supply 4 Schematic Diagram CONTINUE POWER 1 POWER SUPPLY CBA INV+13V LCD+13V P-ON+3.3V LCD-5V CONTINUE LCD+31.5V POWER 1 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM-PWM R210 C201 C217 R218 P-ON-H1 C216 LCD-P-SAFETY 12.9 1000P Q203 KTC3198-Y-AT/P R211 R208 (V-COM DRIVE) C210 JS203 C212 C213 C214...
Page 53 Inverter Schematic Diagram NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. HOT CIRCUIT. BE CAREFUL. INVERTER CBA CN1900 (NO CONNECTION) BC1301 T1950 J1037 J1044 J1027 POWER TRANS WIRE OPEN OPEN OPEN TO POWER SUPPLY CN1901 CBA CN602...
Page 54 Function Schematic Diagram FUNCTION CBA TO IR SENSOR CBA CL103A CL103B AL+3.3V KEY-IN1 R109 R108 C108 D107 C151 D151 R152 R151 OPEN OPEN OPEN OPEN OPEN R111 R112 R113 R114 R115 R153 R154 R155 R156 4.7K 2.7K 4.7K 8.2K OPEN OPEN OPEN OPEN...
Page 55 IR Sensor Schematic Diagram IR SENSOR CBA RS101 KSM-712TH2E (REMOTE SENSOR) C104 R102 R101 TO POWER SUPPLY 3.3K CBA CN101 CL102B R106 REMOTE D108 D109 AL+3.3V C103 C101 C102 OPEN OPEN 330P 47/16V OPEN KEY-IN1 R103 9.1K P-ON+9V D101 SLR343WBCT3XM POWER TO FUNCTION CL103A...
Page 56 Digital Main 1 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 5 DIGITAL MAIN CBA UNIT...
Page 57 Digital Main 2 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. CONTINUE R3002 DIGITAL 3...
Page 58 Digital Main 3 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 5...
Page 59 Digital Main 4 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. IC3301(4/5) DIGITAL MAIN CBA UNIT ZR39775HGCF...
Page 60 Digital Main 5 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 3...
Page 61 Digital Main 1 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. VIDEO SIGNAL CONTINUE DIGITAL 5...
Page 62 Digital Main 2 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 4 R3144...
Page 63 Digital Main 3 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 5...
Page 64 Digital Main 4 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. IC3005(4/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS...
Page 65 Digital Main 5 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. AUDIO SIGNAL CONTINUE DIGITAL 3...
Page 66 Digital Main 6 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE L3046 DIGITAL 5...
Page 67: Troubleshooting
Power Supply CBA & Jack CBA Top View Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 68 Power Supply CBA & Jack CBA Bottom View Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 69 Inverter CBA, Function CBA & IR Sensor CBA Top View Because a hot chassis ground is present in the power supply NOTE: circuit, an isolation transformer must be used when repairing. The voltage for parts in hot circuit is measured using Also, in order to have the ability to increase the input slowly, hot GND as a common terminal.
Page 70 Inverter CBA, Function CBA & IR Sensor CBA Bottom View Because a hot chassis ground is present in the power supply NOTE: circuit, an isolation transformer must be used when repairing. The voltage for parts in hot circuit is measured using Also, in order to have the ability to increase the input slowly, hot GND as a common terminal.
Page 71: Waveforms
WAVEFORMS WF1 ~ WF7 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) Pin 4 of CN302 Pin 17 of CN302 CVBS 0.2V 20µs VIDEO-Pb VIDEO-Pb 0.2V 20µs Pin 8 of CN302 Pin 19 of CN302...
Page 72: Wiring Diagram
WIRING DIAGRAM 12-1 PL11.0WI...
Page 73: Exploded Views
Jack CBA 32PFL3000/F8 (XA1) LCD1 CL1003 CL3702 AC601 CL3701 Digital Main CBA Unit IR Sensor CBA Function CBA CL3902 32PFL3506/F7 (DS2, DS3), 32PFL3000/F8 (XA2) SP801 CL802 CL801 See Electrical Parts List for parts with this mark. SP802 Stand Assembly 13-1 PL11.0-A_CEX...
Page 74 Packing Stand Screw Kit Tape Tape Packing Tape Stand Assembly Packing Tape 32PFL3506/F7 (XA1) CARTON 13-2 PL11.0PEX...
Page 75 TYPE A PARTS LIST [32PFL3506/F7 (Serial No.: DS1), 32PFL3000/F8 (Serial No.: XA1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. ACCESSORIES Before replacing any of these components, read...
Page 76 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C310 CHIP CERAMIC CAP .(1608) CH J 47pF/50V CHD1JJ3CH470 Before replacing any of these components, read C311 CHIP CERAMIC CAP .(1608) CH J 47pF/50V CHD1JJ3CH470 carefully the product safety notice in this service C601#...
Page 77 Ref. No. Description Part No. Ref. No. Description Part No. C803 CHIP CERAMIC CAP .(1608) B K 0.47µF/25V CHD1EK30B474 DIODES C804 CHIP CERAMIC CAP .(1608) B K 0.1µF/25V CHD1EK30B104 D202 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C805 CHIP CERAMIC CAP .(1608) CH J 1000pF/50V CHD1JJ3CH102 D203 SWITCHING DIODE 1SS133(T-77)
Page 78 Ref. No. Description Part No. Ref. No. Description Part No. D655 RECTIFIER DIODE 1N4005 NDQZ001N4005 Q638 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P D657 DIODE ZENER 33BSB-T26 NDTB033BST26 Q639 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D658 DIODE ZENER 3V3BSB-T26 NDTB3R3BST26 Q640 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F D659 DIODE ZENER 5V6BSA-T26 NDTA5R6BST26 Q641...
Page 79 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W 0 Ω RES CHIP 1608 1/10W J 47k Ω R310 RRXA000HH014 R676 RRXA473HH013 RES CHIP 1608 1/10W J 22k Ω RES CARBON FILM T 1/4W J 270 Ω R401 RRXA223HH013 R677...
Page 80 JACK CBA Ref. No. Description Part No. RES CHIP 1608 1/10W J 560 Ω R872 RRXA561HH013 Ref. No. Description Part No. RES CHIP 1608 1/10W J 100k Ω R873 RRXA104HH013 JACK CBA(MPW-B) ---------- RES CHIP 1608 1/10W J 100k Ω R874 RRXA104HH013 Consists of the following:...
Page 81 Ref. No. Description Part No. Ref. No. Description Part No. C1121 CHIP CERAMIC CAP . CH J 330pF/50V CHD1JJ3CH331 D1503 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U C1122 CHIP CERAMIC CAP . CH J 330pF/50V CHD1JJ3CH331 D1504 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U C1123 CHIP CERAMIC CAP .
Page 82 Ref. No. Description Part No. Ref. No. Description Part No. RES CARBON FILM T 1/4W G 470 Ω RES CHIP 1608 1/10W F 100k Ω R1115 RCX4471T1002 R1512 RTW1003HH008 RES CHIP 1608 1/10W F 100 Ω RES CHIP 1608 1/10W F 1.00M Ω R1116 RTW1000HH008 R1513...
Page 83 FUNCTION CBA Ref. No. Description Part No. FUNCTION CBA ---------- Consists of the following: CAPACITOR C108 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 RESISTORS RES CARBON FILM T 1/4W J 220 Ω R108 RCX4221T1001 RES CARBON FILM T 1/4W G 10k Ω R109 RCX4103T1002 RES CARBON FILM T 1/4W G 4.7k Ω...
Page 84 TYPE A PARTS LIST [32PFL3506/F7 (Serial No.: XA1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
Page 85 Different parts from the original model 32PFL3506/F7 (Serial No. : DS1) There are no different parts from the original model 32PFL3506/F7 (Serial No : DS1). Refer to the parts list for the original model 32PFL3506/F7 (Serial No : DS1). 2011/11/22 14-11 A17FCEL.fm...
Page 86 TYPE B PARTS LIST [32PFL3506/F7 (Serial No.: DS2), 32PFL3000/F8 (Serial No.: XA2)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual.
Page 87 RRXA163HH013 Different parts from the original model RES CHIP 1608 1/10W J 16k Ω R880 RRXA163HH013 RES CHIP 1608 1/10W J 33k Ω 32PFL3506/F7 (Serial No. : DS1) R891 RRXA333HH013 RES CHIP 1608 1/10W J 33k Ω R892 RRXA333HH013 RES CHIP 1608 1/10W 0 Ω...
Page 88: Revision History
32PFL3506/F7 (Serial No. : DS2) added • 2011-11-05 32PFL3000/F8 (Serial No. : XA1) added Note: Identical product to the 32PFL3506/F7 (Serial No.: DS1). • 2011-11-05 32PFL3000/F8 (Serial No. : XA2) added Note: Identical product to the 32PFL3506/F7 (Serial No.: DS2).
Page 89 COMPARISON LIST OF MODEL NAME Chassis PL11.0 32PFL3506/F7 (DS1) A17F6UH (DS2) A17FGUH (DS3) A17FHUH (XA1) A17FCMA 32PFL3000/F8 (XA1) A1AF7MA (XA2) A1AFBMA PL11.0COM...

This manual is also suitable for:

32pfl3000/f8

Philips 32PFL3506/F7 Service Manual

Quick Links

Contents

Related Manuals for Philips 32PFL3506/F7

Summary of Contents for Philips 32PFL3506/F7

This manual is also suitable for:

Table of Contents