1. Manuals
  2. Brands
  3. AVS Electronics Manuals
  4. Control Panel
  5. CAPTURE Series
  6. Installation and programming manual

AVS Electronics CAPTURE Series Installation And Programming Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

GENERAL INSTALLATION
PROGRAMMING MANUAL
CAPTURE
CERTIFIED
QUALITY SYSTEM
UNI EN ISO 9001:2008
Spett.le:
Curtarolo (Padova) Italy
www.avselectronics.com
COLORI:
QUADRICRIMIA
DOPO AVER CONTROLLATO
AND
SI PREGA DI CONTROLLARE TUTTI GLI ELEMENTI, NON SOLO LE CORREZIONI EFFETTUATE; NON SIAMO RESPONSABILI DI EVENTUALI E
COLORE. N.B.: In fase di realizzazione i colori di stampa possono subire delle variazioni in base al tipo di carta o eventuale plastificazione, comunque sono sempre soggetti
dei relativi costi anche se solo in parte eseguito, con l'emissione di regolare fattura • Sono comprese nel preventivo una bozza del lavoro da stampare, eventuali altre bozze e
(foto, cd, dvd o altro materiale) fornito dal cliente per l'esecuzione del lavoro, vanno richiesti alla consegna, dopo la quale non si garantisce la restituzione • Gli impianti stampa v
possiamo garantire la reperibilità • I quantitativi ordinati sono soggetti ad una tolleranza in più o in meno dal 5% al 10% e il cliente è tenuto al pagamento della quantità effettiva ric
il committente non potrà nè chiedere risarcimenti nè disdire l'ordine con il rifiuto della merce, adducendo motivi di ritardo • Reclami eventuali, relativi alla qualità e quantità de
merce e non danno il diritto alla sospensione dei pagamenti • Trascorsi 30 gg dall'invio della presente senza alcun riscontro da parte Vostra, provvederemo ad eliminare co
IST0865V1.0
- 1 -
MULTIMAC SRL
SI DÀ IL "VISTO SI STAMPI"
IMQ - Security Systems
EN 50136-2-1
EN 50131-1
EN 50131-3
EN 50131-6
CEB T014
0312
BOZZA 1057
Codice:
RIBOBINATURA:
E1
E2
SI RICHIEDE UN'ALTRA BOZZA CON CONSEGUENTI CORREZIO
Certified products
30/07/2
Data:
E3
E4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CAPTURE Series and is the answer not in the manual?

Questions and answers

Related Manuals for AVS Electronics CAPTURE Series

Summary of Contents for AVS Electronics CAPTURE Series

  • Page 1 MULTIMAC SRL 0312 BOZZA 1057 30/07/2 Spett.le: Codice: Data: Curtarolo (Padova) Italy www.avselectronics.com COLORI: RIBOBINATURA: GENERAL INSTALLATION QUADRICRIMIA DOPO AVER CONTROLLATO SI DÀ IL “VISTO SI STAMPI” SI RICHIEDE UN’ALTRA BOZZA CON CONSEGUENTI CORREZIO SI PREGA DI CONTROLLARE TUTTI GLI ELEMENTI, NON SOLO LE CORREZIONI EFFETTUATE; NON SIAMO RESPONSABILI DI EVENTUALI E COLORE.

  • Page 2: Table Of Contents

    Indice GENERAL INFORMATION ................................... pag. 3 CAPTURE 32 - Technical features ................................pag. 4 CAPTURE 16 - Technical features ................................pag. 5 CAPTURE 8 - Technical features .................................. pag. 6 Type of connections ...................................... pag. 12 Control panel board CAPTURE 32, CAPTURE 16, CAPTURE 8 ......................... pag. 14 Terminal board, Jumper and Connectors CAPTURE 32, CAPTURE 16, CAPTURE 8 ................

  • Page 3: General Information

    The equipment must not be exposed to dripping or water sprays and no object full of liquid must be placed on it. INSTALLATION AND MAINTENANCE MUST BE EXECUTED BY QUALIFIED PERSONNEL AVS ELECTRONICS S.p.a. reserves the right to make amendments at any moment and without notice. - 3 -...

  • Page 4: Capture 32 - Technical Features

    CAPTURE 32 - Technical features Microprocessor control panel that manages all functions typical of a safety and protection system, in that it is able to discriminate the signals coming from burglar proof , fire protection, anti-robbery, medical assistance, etc detectors. The system is made of a control panel and of at least one keypad of (mod.A 500-A500Plus) type and it can be completed with extension satel- lite electronic boards of (mod.C8, XSAT36, XSATPW 3, XSATPW 5, XSAT WS, XSATHP, XSATHP Virtuale) type, with network adapter (mod.

  • Page 5: Capture 16 - Technical Features

    CAPTURE 16 - Technical features Microprocessor control panel that manages all functions typical of a safety and protection system, in that it is able to discriminate the signals coming from burglar proof , fire protection, anti-robbery, medical assistance, etc detectors. The system is made of a control panel and of at least one keypad of (mod.A 500-A500Plus) type and it can be completed with extension satel- lite electronic boards of (mod.C8, XSAT36, XSATPW 3, XSATPW 5, XSAT WS, XSATHP, XSATHP Virtuale) type, with network adapter (mod.

  • Page 6: Capture 8 - Technical Features

    CAPTURE 8 - Technical features Microprocessor control panel that manages all functions typical of a safety and protection system, in that it is able to discriminate the signals coming from burglar proof , fire protection, anti-robbery, medical assistance, etc detectors. The system is made of a control panel and of at least one keypad of (mod.A 500-A500Plus) type and it can be completed with extension satel- lite electronic boards of (mod.C8, XSAT36, XSATPW 3, XSATPW 5, XSAT WS, XSATHP, XSATHP Virtuale) type, with network adapter (mod.
  • Page 7 DISTRIBUTION OF THE ZONES AND OPEN COLLECTORS (O.C.) Central control unit terminals L1, L2, L3, L4 and all terminals L of the satellite models except models XSAT36, XSATPW and XSAT HP can be programmed as zone inputs or as O.C. Outputs, or both at the same time. The central control unit also has 3 terminals O.C.1, O.C.2 and O.C.3 (“physical O.C.”) to which the same number of “software O.C.”...
  • Page 8 SATELLITE 01 C8 - XSAT36 - XSAT PW BASIC Inputs [Sat: I. BA xx] EXTENSION Inputs [Sat: I. EX xx] CLAMP pre-associated SOFTWARE ZONE associated SOFTWARE ZONE ............
  • Page 9 SATELLITE 03 NO CAPTURE 8 C8 - XSAT36 - XSAT PW BASIC Inputs [Sat: M.BA xx] EXTENSION Inputs [Sat: I. EX xx] CLAMP pre-associated SOFTWARE ZONE associated SOFTWARE ZONE ..........
  • Page 10 SATELLITE 05 NO CAPTURE 16 NO CAPTURE 8 C8 - XSAT36 - XSAT PW BASIC Inputs [Sat: M.BA xx] EXTENSION Inputs [Sat: I. EX xx] CLAMP pre-associated SOFTWARE ZONE associated SOFTWARE ZONE ........
  • Page 11 SATELLITE 07 NO CAPTURE 16 NO CAPTURE 8 C8 - XSAT36 - XSAT PW BASIC Inputs [Sat: M.BA xx] EXTENSION Inputs [Sat: I. EX xx] CLAMP pre-associated SOFTWARE ZONE associated SOFTWARE ZONE ........

  • Page 12: Type Of Connections

    Type of connections The CAPTURE central control unit has a basic configuration of eight inputs that can be individually programmed as: - NO (Normally Open), - NC (Normally Closed), which is the DEFAULT state, - Inertial Vibration (balance with one 2300 ohm resistor) - Inertial Roller Shutter (balance with one 2300 ohm resistor) - Inertial Vibration NC (Normally Closed) - Inertial Roller Shutter NC (Normally Closed)
  • Page 13 Inertial Vibration and Inertial Roller Shutter Zones These configurations permit direct management of Inertial or Roller Shutter sensors with one 4700 L4 L5 L6 L7 ohm R1 terminal resistor for the XSAT36 and XSATPW inputs and one 2200 ohm R2 terminal resi- stor (not supplied, or two 4700 ohm R1 resistors in parallel) for the Capture central control unit, C8.

  • Page 14: Control Panel Board Capture 32, Capture 16, Capture 8

    Control panel board CAPTURE 32, CAPTURE 16, CAPTURE 8 OC1OC2 OC3 CONN GSM SNATCH CONN ETH MEMORY CARD 1 2 3 DA DB L4 L5 L6 L7 NO NC C A' B' Terminal board, Jumper and Connectors CAPTURE 32, CAPTURE 16, CAPTURE 8 UPPER SIDE OF ELECTRONIC BOARD J1_ CONN GSM connector for XGSM module (optional)

  • Page 15: Supply Unit Section

    Supply unit section The power supply unit placed in the processing board is stabilised at 13.8 V = and limited in current at 1.2 A. Table Network power supply 230 Vac +10/-15% 50Hz Voltage power supply nominal voltage 13,8 V = Max.

  • Page 16: Keyboard A500 - A500 Plus

    Keyboard A500 - A500 Plus Technical Features 16-character, 2-rows display screen Self-updating micro flash T1 input (with 4K7 resistance and negative reference) T2 input is not used 20 Operational keys TOWARDS OTHER 1= ADDR (Address): 1 KEYPADS 2= Tamper: Enabled 3= Mode: High Speed Edit parameters To access the modify menu for these parameters act as follows:...
  • Page 17 Audio keypads A500Plus enabling (user) The audio enabling of the individual keypads is activated as follows: - Enter user code with “Master” feature and access menu 1 on the keypad to be enabled - Scroll the programming steps up to “A500 Settings” step - Access the menu and adjust the “Audio Volume”...

  • Page 18: Satellites

    Satellites N.B. Expansion cards mod. C8 - XSAT36 - XSAT PW - XSATWS - XSATHP XGSM485 and must be connected to the RS485 serial situated in the same way as keyboards. For more information, refer to the manual of its satellites. INPUTS OUTPUTS OPTIONS...

  • Page 19: Hints On Armings Management

    Addressing Addressing C8 - XSAT36 - XSATPW - XSATWS XSATHP Address Satellite Address Satellite (SW2) Satellite 1 Satellite 1 Satellite 2 Satellite 2 Satellite 3 Satellite 3 Satellite 4 Satellite 4 Satellite 5 Satellite 5 Satellite 6 Satellite 6 Satellite 7 Satellite 7 Satellite 8 Satellite 8...

  • Page 20: Pstn Telephone - Technical Features

    SNATCH PSTN Telephone - Technical features The PSTN telephone is directly integrated on the control panel electronic board, its functioning is subject to the enabling, during programming, of the PSTN telephone section. CONN ETH Outdoor connections: • internal changed and derived telephone line Profiles of phone numbers: •...

  • Page 21: Xgsm - Technical Features

    XGSM - Technical features XGSM is a device which, when used with the Xtream central control unit, allows you to make and receive calls via the GSM mobile phone network. Outdoor connections: • GSM Channel Telephone numbers profiles: • n. 16 numbers, that can be associated to any alarm or technical event Protocols: •...

  • Page 22: Xgsm485 - Xgsm485 Pro - Technical Features

    XGSM485 - XGSM485 PRO - Technical features XGSM485 has a vocal synthesis module that contains 320 pre-recorded words that can be used to customize a maximum of 40 voice messages. If the device does not interface with the control unit, XGSM485 can make absence of interfacing calls to the control unit. The XGSM485 can take two SIM Cards.
  • Page 23 XGSM485 Installation - Warnings XGSM485 should be positioned at least 1m away from sources of electromagnetic interference (ex. transformers, power supplies, etc) and at the same time it should be the same distance away from other equipment that can suffer from the electromagnetic radiation of the GSM, including the control panel itself and its peripherals.

  • Page 24: Checking Credit And Expiry Of The Sim Card For Xgsm - Xgsm485 And Xgsm485Pro

    Checking Credit and Expiry of the SIM Card for XGSM - XGSM485 and XGSM485PRO Credit Check This check is carried out cyclically regardless of the use of the GSM, or when the GSM module carries out operations using credit. Upon reaching of the 8 Euros threshold, the keypad displays the LOW CREDIT strip and, if the calls for have been enabled in the telephone “associate events”, the telephone calls are made.

  • Page 25: Vocal Messages

    A message could be composed as follows: “1” at the office of AVS Electronics S.p.A. in via Valsugana n. .. etc” - “2” sector 3” - “3” production “ - “ etc. etc.” The enabling of the communication message happens using the programming step “account code/messages” from the telephone menu.

  • Page 26: Telephone Table - 1St

    Telephone Table - 1st To every Telephone Code corresponds a certain default pre-recorded vocabulary that can be used to customise the vocal messages of the control panel. Phone Vocal Phone Vocal Phone Vocal Phone Vocal Code communication Code communication Code communication Code communication...

  • Page 27: Telephone Table - 2St

    Telephone Table - 2st To every Telephone Code corresponds a certain default pre-recorded vocabulary that can be used to customise the vocal messages of the control panel. Phone Vocal Phone Vocal Phone Vocal Phone Vocal Code communication Code communication Code communication Code communication...

  • Page 28: Rtc Activation By A Call From The Control Panel

    RTC ACTIVATION BY A CALL FROM THE CONTROL PANEL It is possible to activate the RTC function during an alarm telephone communication, by pressing key (7) after the two-tone signal. Subsequently, the control panel will reply - ENTER CODE -. Now follow the indications shown in the paragraph below. USER RTC ACTIVATION Compose, using a telephone in DTMF (multifrequency or “tones”), the telephone number where the control panel CAPTURE is installed.

  • Page 29: Outgoing Sms Management

    Outgoing SMS Management CAPTURE has the possibility of forwarding specific SMS messages depending on the arisen events. These messages can be technical or alarm and/or to reset the inputs. Technical messages relate to situations which power supply, battery or other anomalies, and are automatically composed by using a library of pre-recorded SMS Zone messages relate to signals of the zone inputs for alarm, reset and exclusion communications.

  • Page 30: Programming

    Programming Hints on sectors management La CAPTURE includes the management of the sectors. This means that up to 8 system in the CAPTURE 32, up to 4 system in the CAPTURE 16 and CAPTURE 8 independent between them can be created with the control panel.
  • Page 31 (by default: Installer Code 1 = 000000; Installer Code 2 = Disabled) Capture ... If the code is recognised, the wording “Capture 32/16/8” will appear avs electronics Press (ENT) to enter SOME PROGRAMMING VALUES MIGHT NOT CORRESPOND TO THOSE ON THE KEYBOARD BECAUSE THEY RELATE TO THE CAPTURE 32 CENTRAL CONTROL UNIT E.G.: User Code (1 - 128) instead of User Code (1 - 64).
  • Page 32 Installation from previus page PSTN enable: By setting “YES”, the PSTN integrated dialler is enabled to dial the programmed calls. PSTN enable XGSM XGSM: By setting “YES”, the GSM integrated dialler is enabled to dial the programmed calls. XGSM485 XGSM485: By setting “YES”, the GMS dialler with serial connection for making the programmed calls is enabled. Conditional arm: By setting NO, the control panel is armed anyway, even if there are unbalanced lines or tamper signals.
  • Page 33 from previus page Macro Macro  The Macros (maximum 64) allow the user to carry out various operations at the same time (maximum 8) using Macro # (1.. 64) the same command: Type of Operation: Operat. # (1.. 8) Operation Type: With this type of operation it is possible to enter a preselected •...
  • Page 34 from previus page Zones Zones  Zone numbers: For every “software” zone it is possible to associate a physical input corresponding to the “clamp” where Zone numbers (1 .. . 32) the detector was wired.  Press (CLR) to vary Phisical input ...
  • Page 35 Zones from previus page Connection Connection: • NC: This configuration allows the central control unit to recognise just the alarm status of the input and is at standby when the connection is negative. • NO: This configuration allows the central control unit to recognise just the alarm status of the input and is in alarm mode when the connection is negative.
  • Page 36 Zones from previus page Test zones: The zone to which the Test function has been enabled does not cause the activation of the programmed Test zones alarm outputs nor the sending of calls, but only the memorising of the occurred alarm. OR zone: If several sectors share the zone, unbalancing triggers the alarm even if a single associated Partition is armed.
  • Page 37 Zones from previus page Zone: Phisical input > Zone It is possible to carry out a research to understand, starting from a physical input, which software zone is Phis. input > zone associated to it.  Select the physical input as previously described and subsequently press (ENT). The associated software zone will be displayed.
  • Page 38 from previus page Tamper Tamper  The zone dedicated to temper proof (T) and the input zones programmed with the “Tamper” modality, can activate the alarm relay. Activates Control Panel Relay: By setting “YES”, the tamper proof alarm will activate the relay in control panel. Activ CP Relay Activates Extensions Relay: Setting “N”...
  • Page 39 from previus page Antimask Antimask  Activ. CP relay Activation CP Relay: the alarm caused by the anti-mask signalling if set on YES will cause the activation of the control panel relay for the time programmed Relay on sat. Activation Relay: the alarm caused by the anti-mask signalling if set on YES will cause the activation of the extension nnnnnnnn relay (C-NC-NA) for the time programmed.
  • Page 40 Open Collector from previus page Tamper Tamper: it activates with the tamper of at least one of the associated zones AntiMask Antimask: it activates with the antimasking of at least one of the associated zones Mains Fault Mains power failure: with “YES”, it activates when the control panel or the supervised power units connected in series are not powered, after a delay programmable in minutes.
  • Page 41 from previus page Timings Timings  Activ. CP Relay Activ. CP Relay: Activation time of the control panel relay MM:SS 3 : 0 Satell. add. Satellite address: Select the satellite of the relay to be programmed (1 .. 8) Activ. Relay Relay time: Activation time of the relay on extension MM:SS 3 : 0 Siren add.
  • Page 42 from previus page Service codes Service Codes  Installer Code 1: this is one of two codes required for complete programming of the central control unit. Installer cod 1  Code # Code #: The value of Installer Code 1 is set by default as 000000 (six zero digits). ...
  • Page 43 User Codes from previus page Skip partition choose: When this option is activated, the user will be able to operate on all his partitions also from Skip part. choose keypads belonging to other partitions (if Master User is in NO). Patrol Tour: ”YES”...
  • Page 44 from previus page User Profiles User profiles  User profile: Every User Code can be associated to one of the 32 available profiles. User prof. # (1 .. 8) The user profiles identify 32 different personalisations to which every user code can refer. The personalisations consist in the enabling or not of certain keypad functions.
  • Page 45 User Profiles from previus page BEEP: In this menu, it is possible to assign a specific function to each channel of the remote control.  - Key number #: select the number between 1 and 8 of the channel to be programmed Key num.
  • Page 46 from previus page Readers Readers  Arming Zone Arming zones  The functioning of the outdoor arming zones is programmed in this Menu for one key electronic board. By accessing and exiting this menu, all pending armings will be disarmed. Key functioning mode Working Mode Pulse mode...
  • Page 47 from previus page Accesses Accesses  In this menu it is possible to program the acquisition of the TOYS that will have access to the control panel. Acquisitions: The acquisition of the TOYS can be carried out through the A500Plus keypads. The individual TOYS are memorised in memory locations from 1 to 128.
  • Page 48 from previus page Keypads Keypads  Keypad number Keypad number: selects the keypad to be programmed (1 .. 8) Partitions Partitions (controlled Partitions): with (Y) the keypad is associated to the Partition. YYYYYYYY The keypad can be associated to work with one or more Partitions. Buzzer: For every keypad the functioning of the Buzzer can be individually enabled, in case of wanting to hear the scanning of only the input, of output and of alarm time.
  • Page 49 A500Plus Audio from previus page A500Plus Audio A500Plus Audio: this menu is used to select the events that will be vocally communicated by the A500Plus keyboard.  Partitions (controlled Partitions): (Y) associates the A500Plus audio to the Partition. Partitions The audio can be enabled to work on one or more Partitions. YYYYYYYY Events to dial Events to dial: In this menu the Audio events are associated to the A500Plus:...
  • Page 50 from previus page WL / XSATHP satellites WL/XSATHP satell  Satellite addr. WL/XSATHP satellite: By accessing in this menu there is the possibility of programming the sensors via (1 . . 8) radio and the sensors addressed performing the acquisition, the deletion and the signal verifications for every acquired sensor.
  • Page 51 from previus page Sirens Sirens  Siren address: in this menu it is possible to program the parameters of the Buzzers with serial connection. Siren add. (1 .. 8) STC command: in this menu it is possible to personalise operation of the red LED and the sound of the Buzzer according to the functions associated with this command STC command ...
  • Page 52 Sirens from previus page PERI Arming PERI Arming: by setting “YES”, it activates when the Partition is armed in PERIMETRO Disarmed Disarmed: by setting “Yes”. It is activated when it is DISARMED, or when the PATROL TOUR TIME ELAPSES. (using the patrol tour function; it signals the failure to enter the patrol tour code within the programmed partition (“patrol tour time”) reactivation time.
  • Page 53 Sirens from previus page Reset Fire Reset Fire: Activated when an enabled user performs a “Reset Fire Line” operation (pressing key 2 in the “User Menu” ). If the time is set as Bistable, the output is activated for 15 seconds.. Timer Timer: it activates when the Timer reaches the pre-fixed day and time;...
  • Page 54 Sirens from previus page Sound level: there is a choice of 8 tones. The values are relative to the sound level of both the Main Sound and the Sound level (1 . . 8) Alternative Sound. 1 is the Maximum and 8 is the Minimum. Max time alarm (minutes): The values are relative to the sound level of both the Main Sound and the Alternative Sound Max time alarm (1 .
  • Page 55 Dialler from previus page In this menu it is possible to memorise up to 16 telephone numbers. For every telephone number, it is possible to define the communication protocol (Vocal, Fast, Sia 1st lev., Sia 2nd lev., Sia_Hayes, Contact-Id), the number of call attempts for every Tel. Num., with which interface (PSTN/GSM) the calls are forwarded and if the main, the Partition and the additional phone must be communicated (for vocal protocols).
  • Page 56 Telephone numbers from previus page Account code Account code: in this menu, the telephone numbers are associated to the active sectors. Each telephone  number can be associated to one or more partitions. Partition # : select the Partition to program Partition # (1 ..
  • Page 57 Telephone numbers from previus page Battery Battery: Communication of the low level state of the battery Autotest: Communicates the self-test Autotest FIRE Zone: Communicates the fire protection alarm received from the Fire lines Fire Zone Interference Interference: Communication of radio interference signal. ON Arming ON Arming: Communication of the Arming in ON modality HOMEArming: Communication of the Arming in HOME modality...
  • Page 58 Dialler from previus page Telephone options Teleph. options  Dial tone listen: ree line tone detection circuit is present inside the telephone; when the line is engaged, it ensures Dial tone listen that the dialling happens only when this is effectively present. In case the detecting of the line tone should be difficult, like in cases of extensions from switchboards, by choosing the option “NO”...
  • Page 59 Dialler from previus page XGSM Credit request personalization: In this menu, it is possible to personalize the credit request method, in the case Credit req. pers.  of variation by the operator. The control panel is programmed for the request by the following operators: Vodafone >...
  • Page 60 Dialler from previus page XGSM485 Server SMTP: This menu is used to set the parameters for sending events via email SMTP Server  SMTP Server: SMTP Server name. Parameter supplied by the service manager. SMTP Server Soket port Socket Port: Technical network parameter Username Username: This is the Username required to access the SMTP Server Password...
  • Page 61 Dialler from previus page Fast Channels FAST channels  Programming of all Channels to be activated for the signalling in Fast Format that do not relate to the zone events. FAST arm/disarm Below are all the Menus that allow entering the various parameters: (1 .
  • Page 62 Dialler from previus page Zones/Open Collector Parameters By entering a value different from zero (0) in the programming step “OC vocal word”, it is possible to customise the vocal communication of the O.C. output state (See telephone table). Open Collector Number (1..32): Select the O.C. output to be customised and subsequently press (ENT). O.C.# (1 ..
  • Page 63 IP Addr A - dev.myavsalarm.com / IP Addr B - dev2.myavsalarm.com: Parameter set by the service operator 27216 (only to be changed if communicated by AVS Electronics). Socket Port A - 27216 / Soket Port B - 272016: Parameter set by the service operator (only to be changed if ...
  • Page 64 from previus page Timer Programm. Timer  The Timer has the possibility of managing the automatic armings of the system and the activations of the OC. Operations OPERATION TYPE  • NO OPERATION: no operation is carried out. Day # •...
  • Page 65 Timer from previus page Holidays Holidays  It is possible to program n. 20 annual holiday periods, during which no programmed function will be carried out. Holiday # (1 .. 10) Example 1: The holiday of only one day, ex. 22/07/97, must be set as follows: 1st - [start day 22] [start month 07] [end day 22] [end month 07] Start Day Example 2: The holiday that starts on 25.04.97 and ends on 26.04.97 must be set:...
  • Page 66 from previus page EWEB / EWEB WIFI EWEB/EWEB WIFI  The following steps must be configured on the basis of the parameters relating to the network to which the device is connected: IP Addr IP Addr: the IP address that allows access to the XWEB board IP Addr 192.168.1.5 0.0.0.0...
  • Page 67 from previus page Copy Copy  This menu enables copying of the features set for one “zone, O.C., User, telephone number” on another “zone, Zones O.C., User and telephone number”.  Example - Zone Just select the zone number to be copied From =>...
  • Page 68 from previus page EEPROM Reset EEPROM Reset  Confirming RESET EEPROM causes the resetting of the entire control panel configuration bringing it back to default Are you sure..?? values, excluding the Events Memory. CLR=NO ENT=YES Press (ENT) to reset all default parameters Press (CLR) to go back USB link USB link...
  • Page 69 Zones Walk Test from previus page The zones’ test function allows to display the state of all zones for the control panel/keypads/satellites. Zones Walk Test  - Key (5), allows to deactivate or activate the memory function. Also, by exiting and entering the MEMO function, the previous memorisations are deleted.

  • Page 70: Manufacturers Declaration Of Conformity R&Tte 99/05/Ce

    MANUFACTURERS DECLARATION OF CONFORMITY R&TTE 99/05/CE AVS ELECTRONICS S.p.A. a Socio Unico Via Valsugana, 63 – 35010 Curtarolo (PD) Italy Tel. 049 96 98 411 r.a. Fax 049 96 98 407 PEC: ammin.avs@legalmail.it www.avselectronics.com - avs@avselectronics.it Cap. Soc. €. 800.000,00 i.v.
  • Page 71 Via Valsugana, 63 35010 (Padova) ITALY Tel. 049 9698 411 / Fax. 049 9698 407 avs@avselectronics.it www.avselectronics.com support@avselectronics.it - 71 -...

This manual is also suitable for:

Capture 8Capture 32Capture 16

Table of Contents

Save PDF