Table of Contents
Advertisement
Quick Links
HCD/HMD/HCF/HMF1810RPS, HCD/HMD/HCF/HMF2110RPS,
HCD/HCF1810NPS, HMD2110NPS
(See model number configurator on page 2 for details.)
Order parts online
www.follettice.com
Horizon Elite
Ice Machine Models with RIDE
™
Installation Instructions for Cornelius PR150
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Technology
™
remote condensing
01157882R01
Advertisement
Table of Contents
Related Manuals for Follett Horizon Chewblet 1810 Series
Summary of Contents for Follett Horizon Chewblet 1810 Series
- Page 1 Horizon Elite Ice Machine Models with RIDE Technology ™ ™ Installation Instructions for Cornelius PR150 HCD/HMD/HCF/HMF1810RPS, HCD/HMD/HCF/HMF2110RPS, HCD/HCF1810NPS, HMD2110NPS (See model number configurator on page 2 for details.) Order parts online www.follettice.com remote condensing 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 •...
- Page 2 Chewblet Ice Machine Model Number Configurations ® 1810 Application Configuration Icemaker Voltage Series Condenser MC Maestro™ C 208-230/60/1 (icemaking head) 425 up to A Air-cooled, self-contained V Vision™ S RIDE™ Self-contained only. 425 lbs Chewblet ® W Water-cooled, self-contained H Harmony™ (RIDE remote D 115/60/1 (icemaking head) (193 kg)
- Page 3 Read and complete the following 8 installation steps Unpack Site preparation Dispenser preparation Louvered docking assembly Ice transport tube External connection Internal connection Front cover Cornelius • RIDE Technology remote condensing...
-
Page 4: Unpack Ice Machine
Unpack Carefully unpack and inspect the contents of your Follett ice machine. Unpack ice machine ➋ ➌ ➊ ➎ ➍ 7/16" DO NOT TILT ICE MACHINE TO ACCESS BOLTS! COMPRESSOR DAMAGE 7/16" WILL RESULT ➐ ➏ Cornelius • RIDE Technology... -
Page 5: Prepare The Installation Site
• 10-70 psi (69-483kpa) • 45-90 F (7-32 C) • Follett recommends the use of an in-line water filtration system (item# 00130286) • This equipment is to be installed with adequate backflow protection to comply with applicable federal, state, and local codes Drain ➌... -
Page 6: Dispenser Preparation
Dispenser preparation Prepare the dispenser. ➋ ➋ ➊ ➊ • Coil capillary tube and secure away from bin • ➊ Remove ice entry cover plate ➊ fill opening • Remove bin thermostat capillary tube from ➋ bracket ➊ ➊ ➋ ➋... - Page 7 ➋ ➌ ➊ ➊ ➋ • • I Mount cover plate/transport tube assembly nsert end of ice transport tube (with retaining on outside of dispenser using screws, flat holes) through hole in center of cover plate ➊ ➋ ➊ washers , lock washers and nuts assembly...
-
Page 8: Before Proceeding
3.10 ➊ ➊ ➋ • • Route thermostat capillary tube through Insulate entire length of ice transport tube ➊ ➊ mounting bracket grommets as shown and route to icemaker in accordance with directions in Horizon installation instructions • ➋ Route bin signal wire to icemaker BEFORE PROCEEDING Prior to installing the louvered docking assembly, ensure that the drain fitting is... - Page 9 Louvered docking assembly Install the louvered docking assembly. Wall bracket accessory Machine stand accessory • Mount louvered docking assembly to wall • Mount louvered docking assembly to bracket accessory machine stand accessory Louvered docking assembly 2" (50,8 mm) 1.81" (46 mm) ➋...
- Page 10 Undercounter installation requirements Top View ➌ ➊ Access panel/ 3.25" (83 mm) min. door on counter 23.5" min. (59.7 mm) 24" min. (61 mm No Lip ➋ DOCKING STATION • Prior to installing the louvered docking assembly, ensure that the drain fitting is oriented (right or left) correctly for your installation.
-
Page 11: Ice Transport Tube
Ice transport tube Install the ice transport tube. Ice transport tube installation from dispenser to ice machine ➋ Hot Water 160 F (71 C) ➎ ➊ 1/4" ➌ ➍ ➏ ➐ Ice transport tube tips • Insulate entire length of ice transport tube ➊... - Page 12 Bin signal Install the bin signal. Bin Signal Installation ➏ ➎ ➐ ➌ 24" (610 mm) ➋ Ground ➊ ➌ • Mount the electrical box to the side of the Vision dispenser ➊ to establish a ground connection. Note: If a 4 x 4 box is mounted to a non-grounded surface, connect ground wire at an appropriate ground.
-
Page 13: External Connections
External connections Connect utilities to louvered docking assembly. Refrigerant Water and drain ➊ ➋ ➊ ➌ Minimum 8" ➏ radius 2 ft. x 1" OD silicone tubing • Braze supplied quick-connect lines onto ➊ stub-ins 3/4" barb x 3/4" FPT ➍... -
Page 14: Internal Connections
Internal connections Connect louvered docking assembly to ice machine. Ice transport tube installation Water line ➋ ➊ ➊ • Slide ice machine into louvered docking ➊ • Insert potable water line into valve assembly ensuring that drain tube is fully ➊... - Page 15 Power cord TDS switch HIGH CLEAN • Position plate into opening and secure • Set the TDS switch on the electrical box: with supplied screw HIGH: for extended service life LOW: for low-scale water Cornelius • RIDE Technology remote condensing...
-
Page 16: Front Cover
Front cover Install front cover to ice machine. Install condensing unit Install ice machine front cover ➋ ➊ • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered • Complete installation of condensing unit docking assembly ➊... - Page 17 Long tube run recommendations max. 2 ft (.6m) 1/4" ➊ • Pitch ice transport tube to allow melt water to drain towards ice machine ➋ • Secure insulated ice transport tube at least every 2 ft (.6m) to prevent dips or traps Cornelius •...
- Page 18 Cornelius • RIDE Technology remote condensing...
- Page 19 Cornelius • RIDE Technology remote condensing...
- Page 20 Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge and Vision are trademarks of Follett LLC. Chewblet, RIDE and Follett are registered trademarks of Follett LLC, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 01157882R01 www.follettice.com...
Need help?
Do you have a question about the Horizon Chewblet 1810 Series and is the answer not in the manual?
Questions and answers