12.Set.default.gateway; Set Port; Save/Load Remote Camera Configuration File - Panasonic AK-HRP200G Operating Instructions Manual

Setup.Mode.Operations.

12.Set.default.gateway

1..
Press.<SELECT>.to.select.menu.number.[12].
• Block 1 of the default gateway appears.
Press to select the
default gateway
UP
ND CC
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD
Press to switch the block
Press to exit setup mode (hold down)
2.. Press.<SAVE/LOAD>.to.select.[CC],.[SHT],.and.[SYNC].
• The display changes in the order of block 1, block 2, block 3, and
block 4.
• When changing the default gateway, press <UP> or <DOWN> to
change the setting for each block.
ND
M.GAIN
3..
Press.<SHUTTER>.to.confirm.the.default.gateway.
setting.
• Pressing <SHUTTER> while block 4 is displayed confirms the
setting.
ND
M.GAIN
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• If the default gateway setting value has been changed, the unit will
restart automatically when you exit setup mode. If the setting value
has not been changed, the unit will not restart.
• To make other settings, press <SELECT> to select a menu number.
„ Settable.addresses
„
192. 168.
Block 1 Block 2
For the IP address, you can set a value within the following ranges.
Block 1 1 to 223
Block 2 0 to 255
Block 3 0 to 255
Block 4 1 to 254
However, "127.0.0.1" cannot be set even though it is within the above
ranges.
For the subnet mask, you can set a value within the following ranges.
Block 1 0 to 255
Block 2 0 to 255
Block 3 0 to 255
Block 4 0 to 255
However, "0.0.0.0" and "127.0.0.1" cannot be set even though it is
within the above ranges.
16
(continued)
Display/set block 1
Display/set block 2
Display/set block 3
Display/set block 4
CAMERA
SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
0. 130
Block 3 Block 4
For the default gateway, you can set a value within the following
ranges.
Block 1 0 to 255
Block 2 0 to 255
Block 3 0 to 255
Block 4 0 to 255
13.Set.port
1..
Press.<SELECT>.to.select.menu.number.[13].
• The 3 digits of the port number appear.
Press to select
the port
UP
ND
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD
Press to switch the block
Press to exit setup mode (hold down)
2.. Press.<SAVE/LOAD>.to.select.[CC].
• The display changes to the next 2 digits.
ND
M.GAIN
• Press <UP> or <DOWN> to change the setting for each block.
• Press <SHUTTER> to confirm the setting.
• A value within the range of 35200 to 35599 can be set for the port
number.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• If the port number setting value has been changed, the unit will restart
automatically when you exit setup mode. If the setting value has not
been changed, the unit will not restart.
• To make other settings, press <SELECT> to select a menu number.
14.Save/load.remote.camera.configuration.file
The data recorded by the remote camera can be saved to a memory
card.
Press.<SELECT>.to.select.menu.number.[14].
Select y (Execute)/
Save indication
n (Cancel)
Load indication
UP
ND
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD
Save/load selection confirmation
Press to exit setup mode (hold down)
First 3 digits
Last 2 digits
CAMERA
CC SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
CAMERA
CC SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number