Advertisement
Advertisement
Table of Contents
Summary of Contents for Anchorlift Barracuda 600
- Page 1 User Manual Installation Guide www.anchorlift.com...
- Page 2 Our Anchorlift windlass and accessories are heralded for their durability and performance. Based on an all Stainless Steel AISI 316L production platform, we take great pride in providing products that will endure the test of time and the harsh elements they are exposed to. We back these claims with an industry leading 5 Year Warranty that reflects our pride in our products and their reliability.
- Page 3 Important Thank you for choosing Anchorlift windlass systems. Please take the time to read the instructions contained in this User Manual & Installation Guide carefully. This will fully explain and illustrate for you the proper installation and general maintenance of your windlass for years of dependable operation.
- Page 4 Mako: 25mm to 65mm, 1" - 2.5" Aquarius: up to 190mm / 7.5" Note: For deck thickness greater than the maximum measures mentioned here please contact Anchorlift Customer Support for available options. The Gear Box is fitted with a removable mounting flange that can be mounted on both sides of the gear box. It’s important that the motor is mounted as far away from the chain pipe hole as possible.
-
Page 5: Installation
Barracuda, Dolphin & Mako models are equipped with 8mm stainless steel bolts. When installing the windlass use a 10mm drill bit for the bolt holes. Before installing turn the windlass over and supply a suitable bead of sealant as shown below. www.anchorlift.com... - Page 6 It may be necessary to move the motor/gear box up and down the shaft to make sure the grease is completely covering the entire shaft. Apply thread locker to exposed threads and assemble with stainless steel hardware supplied. After installation: Use anti corrosion marine protection on the motor and gearbox. See photo P 2. www.anchorlift.com...
-
Page 7: Cable Sizes
Always use a circuit breaker to protect the windlass motor and electrical cables. Cable sizes We recommend the use of the following cables, switch-wiring and circuit breaker sizes: Windlass Cable length: 0-8m 0-24ft over 8m 24ft Circuit Breaker Barracuda 600 16mm2 4-6AWG 25mm2 4AWG 80amp (90080) Barracuda 900... -
Page 8: Wiring Diagram
Wiring Diagram Electrical connections 2 wire motor. 2 wire motor wiring diagram Switch panel 90801 UP / DOWN Panel Barracuda 600 - 900 Dolphin 1000 Battery + supply for foot switch, radio remote, hand held remote. Motor Black Yellow 3-Conductor cable 1.5mm (16AWG) -
Page 9: Selection Guide
Selection Guide Motor boat installation using the vertical low pro le windlass model with 2 wire motor. Sail boat installation using the vertical low pro le windlass model with 3 wire motor. www.anchorlift.com... -
Page 10: Parts & Maintenance
Clean all the parts to prevent corrosion and grease the Shaft (10) and Gypsy (18) where the clutch cones seat (17). Use suitable marine grease ONLY! Reassemble following the instructions and drawings above. WARNING MAKE SURE THE ELECTRICAL POWER TO THE MOTOR IS SHUT OFF WHEN WORKING ON THE WINDLASS. CAREFULLY REMOVE THE CHAIN OR ROPE FROM THE GYPSY. www.anchorlift.com... - Page 11 Rope and Chain Anchorlift windlasses are designed to operate using chain only and chain/rope combinations. The table below shows a selection of chain and rope that is specified for each model. Note: Chain specification is HT G43 Windlass Chain. Rope specification is 8 –...
- Page 12 3/8” / 10mm 15ft / 4.5m 215ft / 65m Mako SSDB3/8-250 5/8”/16mm 250ft / 75m 3/8” / 10mm 20ft / 6m 270ft / 82m Mako SSDB3/8-300 5/8”/16mm 300ft / 90m 3/8” / 10mm 20ft / 6m 320ft / 82m Mako www.anchorlift.com...
-
Page 13: Troubleshooting
Third: check your Gypsy for markings embossed on it that will indicate chain size: ¼” - 6mm, 5/16”-10mm, etc. and lastly you can help determine which windlass you have by the size of your boat: Up to: 30ft. = Barracuda 600, 35ft. = Barracuda 900, 45ft. = Dolphin 1000, 75ft. -
Page 14: Warranty
Anchorlift warrants to the original purchaser that your purchase (the "Product") shall be free from defects in materials and workmanship under normal use for a period of five (5) years from the date of purchase. Anchorlift does not warrant that the operation of the Product will be uninter- rupted or error-free. -
Page 15: Control Units
10 3/8” 964412 Chain 10-14mm 3/8-9/16” 964420 Chain 16-20mm 5/8-3/4” Bow Plank Rollers TPX Anchors Boats 20-90 ft. Solid Stainless Steel Sizes: 6 kg / 13.2 lbs to 120 kg / 264 lbs Lifetime Warranty 90113, 90114 & 90115 www.anchorlift.com...
Need help?
Do you have a question about the Barracuda 600 and is the answer not in the manual?
Questions and answers