Setting The Timers To Go On And Off And The Temperature For Each; Boost; Holiday Mode; Error Codes - EasiWise Standard Quick Start User Manual

• S
T
ETTING THE IMERS TO
As described above default timers will have been set for off at 6am, on at 9am then off at 6pm and on at 9pm. To
get the best savings on electricity and still have hot water on tap, you can set the on and off to suit your needs.
Long press the '"DOWN" button - the light in the top left will go off, when it is back on,
➢
release the "DOWN" button
Setting 1 - On: Hour will flash, press "UP" or "DOWN" until the desired on
➢
hour appears, press "ENTER".
Minutes will flash, press "UP" or "DOWN" until the desired minute
➢
appears, press "ENTER".
Setting 1 - Off: Hour will flash, press "UP" or "DOWN" until the desired hour appears, press "ENTER".
➢
Minutes will flash, press "UP" or "DOWN" until the desired minute appears, press "ENTER".
➢
Setting 1 - Temperature: Temperature will flash, press "UP" or "DOWN" until the desired temperature appears,
➢
press "ENTER".
You have now set the timer to go on and off as well as the temperature you require your geyser to heat to.
There are two timer and temperature programs, one for Monday to Friday and one for weekends, each with four
timer / temperature settings to choose: settings 1-4 are for weekdays and setting 5 – 8 for weekends:
Program 1 – Monday – Friday (settings 1 – 4)
NOTE: You do NOT need to set all options, only those times when you require the element to go on. If you do not
require the element to go on, you can set both the "on" and "off" time to 00:00.
• B
OOST
The Boost function allows you to override the timer for when you want the geyser to instantly heat up, without
resetting any timers.
Short press "BOOST" - the element will switch on for 1 hour, heating the
water, and then off. None of the set timers and temperatures will be
changed.
•

HOLIDAY MODE

Holiday mode allows you to override all timers indefinitely, turning the geyser
off and staying off until this is cancelled. Long Press "BOOST". "HLDAY" will
display in the Time/Date menu. The element will not come on in this mode.
Press "BOOST" to cancel, that is turn Holiday Mode off.
•

ERROR CODES

Your EasiWise is not just a timer, but also a geyser manager. Should your geyser or solar system develop a fault, the
system will display an error code on the LCD.
Fault Code
Fault 1 + E-Leakage
Fault 2
Fault 3 + T-Sensor
Fault 4
Fault 5
Fault 6 + Leak
Fault 7
Fault 8
Fault 9
Fault 0
And finally – ensure your unit is registered!
W S
ARRANTY AND ERVICE
EasiWise have made it easy to register your unit. In order to activate the
warranty, please complete the activation by going to www.easiwise.co.za/Owner Login/ Activate My EASIWise on
any internet connected device. The serial number of the main roof unit, is used for the initial login. Alternatively, the
registration form can be downloaded from the EasiWise website and emailed to support@easiwise.co.za or faxed to
021 946 3989. IMPORTANT: GSM enabled EASIWISE controllers will only be activated once the Owner has completed
the registration / activation online.
EWT-UserQuickGuide-01
G O O
O N AND FF AND THE
Problem Detected
Earth Leakage
Reserved for future use
Geyser temperature sensor fault
Geyser temperature <4°C / Hr
Geyser temperature over 85 °C
Water leak
Reserved for future use
Solar temperature sensor fault
Solar pump fault
Reserved for future use
A P
CTIVATION ROCESS
Problems? Call us on 021 946 3424, ask for EasiWise support
T E
EMPERATURE FOR ACH
Program 2 – Saturday & Sunday (settings 5 – 8)
Page 2