Summary of Contents for Backyard Discovery SKYFORT II SWING SET
Page 1
SKYFORT II SWING SET Owner's Manual & Assembly Instructions SAVE THIS ASSEMBLY MANUAL FOR FUTURE REFERENCE IN THE EVENT THAT YOU NEED TO ORDER REPLACEMENT PARTS. Free BILT Intelligent Instructions Download on https://biltapp.com/ Available on Apple and Google Play Adult Assembly Required.
Page 2
GENERAL SAFETY INSTRUCTIONS PURPOSE This product is intended for outdoor, domestic use only. It is not suitable for commercial or medical use. DANGER FOR CHILDREN WARNING! No eating while using the product This product may only be used with adult supervision at all times. ...
Page 3
In certain areas during winter, snow buildup and the low temperatures can damage the product. It is recommended to remove snow buildup and to store the product indoor. We strongly recommend visual inspections every 3 months to insure the integrity of the entire product. Replace any parts as necessary.
Page 4
Consumer Information Sheet for Playground Surfacing Materials The US Consumer Product Safety Commission (CPSC) estimates that about 100 000 playground equipment- related injuries resulting from falls to the ground surface are treated annually in US hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head.
Page 5
WOOD ADVICE Our products are manufactured from premium timber. Great care is taking in selecting, machining and treating the timber before it is sold to you. 1. Inspect wood parts monthly. The grain of the wood sometimes will lift in dry periods causing splinters to appear.
Page 6
• The swing frame must not be installed directly on cement, asphalt, or any other hard surface. • Your swing frame must be attached on a flat horizontal surface with a minimum of 2m between it and any structure or obstacle such as a fence, garage house, tree branches, cloths lines, or electric cables. For more information: http://www.lifespankids.com.au/natural-timber...
Page 7
10. The end beam is not straight up and down. Why not? This is normal. Backyard Discovery designs playsets this way to ensure the strongest structure possible. The slight angle adds strength and reduces rocking and twisting.
Page 8
Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.) (Level 24") (Square) (Open End Wrenches 1/2", (Phillips Screw Driver) (Drill Attachments: &...
Page 9
Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 33'-11 1/8" [10.3] 21'-11 1/8" [6.7] 6'-0"...
Page 10
Parts Identification Wood Components (NOT TO SCALE) A50 - SWING BEAM - W4L04660 3 3/8"x5 1/4"x89 1/2" (86x134x2274) B1 - TOWER LEG - W4L04562 3"x3"x89 1/2" (76x76x2274) B2 - TOWER LEG - W4L04561 3"x3"x89 1/2" (76x76x2274) B3 - TOWER LEG - W4L04564 3"x3"x59"...
Page 11
Parts Identification Wood Components (NOT TO SCALE) E50 - END SUPPORT - W100949 1 3/8"x3 3/8"x44 1/8" (36x86x1120) E51 - ANGLE BRACE - W100948 1 3/8"x3 3/8"x88 3/4" (36x86x2254) E74 - MONKEY BAR RAIL - W102918 1 3/8"x3 3/8"x77 1/8" (36x86x1959) E77 - LEFT UPRIGHT - W4L11769 1 3/8"x3 3/8"x64 3/8"...
Page 23
Parts Identification Accessories (NOT TO SCALE) DP - SWING SEAT GREEN - A100027 DN - GLIDER SEAT DARK GREEN - A100025 DJ - GLIDER ARM LIGHT GREEN - A100021 DR - SLIDE RAIL 10' BOTTOM LEFT GREEN - A100030 DT - SLIDE RAIL 10' TOP LEFT GREEN - A100032 DS - SLIDE RAIL 10' BOTTOM RIGHT GREEN - A100031 - GREEN HC ROCK #1 - A6P00036 TR - SLIDE RAIL 10' TOP RIGHT GREEN - A100033...
Page 24
Parts Identification Accessories (NOT TO SCALE) EF - CHAIN GREEN 57" - A100047 HW - CHAIN GREEN 44" - A100048 - HAND GRIP GREEN 816 C/C - A100134 - LADDER RUNG 629 GREEN - A100324 FA - QUICK LINK - A100069 - HAND GRIP METAL GREEN 381 c/c - A100118 SS - "C"...
Page 31
Y3 - ROCK WALL END BOARD - W4L04682 5/8"x4"x22 7/8" (16x102x580) ROCK WALL ASSEMBLY STEP 3 SCREW PFH 8x1-1/2" SCREW PFH (4 PLCS) 8x1-1/2" H100086...
Page 32
1 1/2 in [37 mm] M61 - ATTACHMENT BOARD - W4L04681 5/8"x3 3/8"x22 7/8" (16x86x580) ROCK WALL ASSEMBLY STEP 4 SCREW PFH 8x1-1/2" H100086 T-NUT 5/16 H100074 T-NUT 5/16 (2 PLCS) HOLES CLOSER TO THE BOTTOM OF BOARD SCREW PFH 8x1-1/2" (4 PLCS) IMPORTANT! T-NUTS TO THE INSIDE...
Page 33
- GREEN HC ROCK #2 - A6P00037 - GREEN HC ROCK #1 - A6P00036 ROCK WALL ASSEMBLY STEP 5 WASHER BOLT PTH LOCK INT (24) 1/4x3/4 (24) 8x15 H100063 H100108 BOLT PTH 1/4x3/4 (24 PLCS) WASHER LOCK INT 8x15 (24 PLCS) NOTE: ARROW ON BACK OF ROCK POINTS UP.
Page 34
E74 - MONKEY BAR RAIL - W102918 1 3/8"x3 3/8"x77 1/8" (36x86x1959) TZ - L BRACKET 2.5x38x50x55 - A100340 EC - METAL RUNG 559 GREEN - A100045 QZ - TRIANGLE PLATE 100° 5 HOLE - A100294 MONKEY BAR ASSEMBLY STEP 1 SCREW NUT LOCK TAPPING...
Page 35
E79 - MONKEY BAR UPRIGHT - W100995 1 3/8"x3 3/8"x88 1/8" (36x86x2237) EC - METAL RUNG 559 GREEN - A100045 FX - HAND GRIP METAL GREEN 381 c/c - A100118 MONKEY BAR ASSEMBLY STEP 2 SCREW TAPPING 14x1-1/2 H100109 LAG SCREW HAND GRIP METAL GREEN 381 c/c WH 5/16x1 1/2 H100026...
Page 38
M70 - SLIDE BED SUPPORT - W100935 DX - SLIDE BED 10' LIGHT GREEN - A100035 5/8"x3 3/8"x19 7/8" (16x86x505) 10 FOOT SLIDE ASSEMBLY STEP 1 BOLT WH 5/16x1/2 WASHER LOCK EXT 12x19 NUT BARREL WH 5/16x5/8 DX - SLIDE BED 10' LIGHT GREEN (SEE SLIDE ASSEMBLY INSTALLATION STEP FOR DECK MOUNTING HOLE...
Page 39
DS - SLIDE RAIL 10' BOTTOM RIGHT GREEN - A100031 TR - SLIDE RAIL 10' TOP RIGHT GREEN - A100033 DR - SLIDE RAIL 10' BOTTOM LEFT GREEN - A100030 DT - SLIDE RAIL 10' TOP LEFT GREEN - A100032 10 FOOT SLIDE ASSEMBLY STEP 2 BOLT WH...
Page 40
DW - SLIDE SUPPORT TUBE 21.34x2.77x505 - A100034 21.34 OD x 2.77 W x 505 10 FOOT SLIDE ASSEMBLY STEP 3 PLACE (1) SLIDE RAIL ASSEMBLY ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE SLIDE RAIL (FIG. 1). HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT THE BED INTO THE SLIDE CAVITY.
Page 41
10 FOOT SLIDE ASSEMBLY STEP 4 ONCE THE SLIDE BED, SUPPORT TUBES, AND SUPPORT BOARD ARE COMPLETELY IN THE CAVITY AND SUPPORT POCKET, SECURE USING 2-1/2" SCREWS AT EACH OF THE PILOT HOLE LOCATIONS AS SHOWN. REPEAT PROCESS FOR OPPOSITE SLIDE RAIL. SCREW PFH (38) 8x2 1/2...
Page 42
DN - GLIDER SEAT DARK GREEN - A100025 DJ - GLIDER ARM LIGHT GREEN - A100021 Light Green & Dark Green Glider WASHER FLAT 8x27 H100105 NUT LOCK 5/16 H100110 BOLT WH 5/16x5 3/4 H100032 NUT LOCK 5/16 (2 PLCS) WASHER FLAT 8x27 (2 PLCS) BOLT WH 5/16x5 3/4...
Page 43
G5 - BAY WINDOW HEADER - W4L04659 1"x5 1/4"x45 1/4" (24x134x1150) (6) WP1 - BAY WINDOW PANEL - W2A01496 BAY WINDOW ASSEMBLY SCREW PFH 8x1-1/2" (8 PLCS) MAKE 2 WINDOW ASSEMBLIES. SCREW PFH (40) 8x1-1/2" H100086 SCREW PFH H100085 NOTE: MARK CENTERS ON EACH PART THEN ALIGN PARTS ON MARKS.
Page 44
H20 - PORCH ROOF RAFTER - W4L04655 1"x3 3/8"x24 1/2" (24x86x622) PORCH ROOF ASSEMBLY STEP 1 SCREW PFH 1/2 in 8x2 1/4 1 1/4 in H100091 USING A 3/16" DRILL BIT, MARK AND DRILL A PILOT HOLE INTO 'H20' RAFTER TO PREVENT SPLITTING. ONLY DRILL THROUGH ONE RAFTER NOT BOTH.
Page 45
N8 - FRONT PORCH GABLE TRIM - W4L04657 M19 - FRONT PORCH ROOF SUPPORT - W4L04658 5/8"x2 3/8"x9 1/2" (16x60x241) 5/8"x3 3/8"x30 5/8" (16x86x779) N5 - FRONT PORCH GABLE TRIM - W4L04656 5/8"x2 3/8"x15" (16x60x381) HC - BYD ID TAG (LARGE) AGES 3-10 - A100164 PORCH ROOF ASSEMBLY STEP 2 SCREW PFH...
Page 75
Y1 - TOP FLOOR BOARD - W4L04609 5/8"x4"x78" (16x102x1980) FP2 - FLOOR PANEL - W2A01486 1 1/4"x13 1/2'x81 7/8" (32x344x2080) FORT ASSEMBLY STEP 21 T-NUT 5/16 SCREW PFH (2 PLCS) T-NUT 5/16 (94) 8x1-1/2" H100074 H100086 TIP: INSTALL T-NUTS ON BOTTOM SIDE OF BOTH Y1 FLOOR BOARDS BEFORE ATTACHING TO FORT.
Page 76
1 3/4 in 1 1/2 in B8 - BACK RIGHT CLUB HOUSE CORNER - W4L04618 3"x3"x53 7/8" (76x76x1370) H4 - ROOF SUPPORT RAIL - W4L04623 M21 - CLUB HOUSE WALL RAIL - W4L04613 1"x3 3/8"x67 1/4" (24x86x1709) 5/8"x3 3/8"x30 1/4" (16x86x768) L BRACKET 2.5x38x50x55 B5 - BACK LEFT CLUB HOUSE CORNER - W4L04612...
Page 77
1 1/2 1 3/4 M1 - TOP WALL RAIL - W4L04619 5/8"x3 3/8"x80" (16x86x2032) M34 - WALL RAIL - W4L04611 M10 - CLUB HOUSE WALL RAIL - W4L04614 5/8"x3 3/8"x6 3/8" (16x86x162) 5/8"x3 3/8"x50 1/4" (16x86x1277) FORT ASSEMBLY STEP 23 LAG SCREW WH 5/16x2 H100027...
Page 84
H4 - ROOF SUPPORT RAIL - W4L04623 1"x3 3/8"x67 1/4" (24x86x1709) H7 - FRONT CLUB HOUSE WALL RAIL - W4L04625 1"x3 3/8"x60 1/2" (24x86x1537) FORT ASSEMBLY STEP 30 BOLT WH WASHER 5/16x3 3/4 T-NUT 5/16 LOCK EXT H100019 H100074 8x19 H100030 BOLT WH 5/16x3 3/4 (4 PLCS)
Page 85
1 1/2 in 1 3/4 in L BRACKET H8 - CLUB HOUSE LEG - W4L04637 M21 - CLUB HOUSE WALL RAIL - W4L04613 2.5x38x50x55 1"x3 3/8"x50 1/2" (24x86x1284) 5/8"x3 3/8"x30 1/4" (16x86x768) A100340 FORT ASSEMBLY STEP 31 LAG SCREW BOLT WH BOLT WH BOLT WH WH 5/16x2...
Page 86
H13 - CLUB HOUSE WALL RAIL - W4L04624 1"x3 3/8"x50 1/4" (24x86x1277) FORT ASSEMBLY STEP 32 LAG SCREW WH 5/16x2 H100027 WASHER LOCK EXT 8x19 H100030 LAG SCREW WH 5/16x2 (2 PLCS) WASHER LOCK EXT 8x19 (2 PLCS)
Page 87
NOTE: H10 - PORCH LEG - W4L04683 HOLES GO OUTWARD 1"x3 3/8"x50 1/2" (24x86x1282) WHEN INSTALLED. L BRACKET H11 - PORCH LEG - W4L04610 2.5x38x50x55 1"x3 3/8"x50 1/2" (24x86x1282) A100340 FORT ASSEMBLY STEP 33 BOLT WH BOLT WH NUT BARREL BOLT WH 5/16x1 1/2 5/16x1 3/4...
Page 88
N1 - CLUB HOUSE WALL BOARD - W4L04629 5/8"x2 3/8"x50 1/2" (16x60x1284) M8 - CLUB HOUSE WALL BOARD - W4L04630 5/8"x3 3/8"x50 1/2" (16x86x1284) M22 - CLUB HOUSE WALL BOARD - W4L04633 5/8"x3 3/8"x29 7/8" (16x86x758) M9 - CLUB HOUSE WALL BOARD - W4L04631 M23 - CLUB HOUSE WALL BOARD - W4L04634 5/8"x3"x50 1/2"...
Page 96
H12 - ROOF RAFTER - W4L04640 1"x3 3/8"x50 3/8" (24x86x1278) FORT ASSEMBLY STEP 42 BOLT WH WASHER 5/16x1 3/4 LOCK EXT H100011 1 in 8x19 H100030 USING A 3/16" DRILL BIT, MARK AND DRILL A PILOT SCREW PFH HOLE INTO 'H12' RAFTER TO PREVENT SPLITTING. 8x2 1/4 T-NUT 5/16 ONLY DRILL THROUGH ONE RAFTER NOT BOTH.
Page 121
(1) MONKEY BAR ASSEMBLY FINAL ASSEMBLY STEP 2 T-NUT 5/16 H100074 BOLT WH 5/16x1 T-NUT 5/16 H100008 (4 PLCS) BOLT WH 5/16x1 (4 PLCS) MONKEY BAR ASSEMBLY...
Page 122
(1) SLIDE FINAL ASSEMBLY STEP 3 NOTE: BOLT WH CENTER SLIDE IN OPENING. USING DIMENSIONS BELOW AS 5/16x1/2 H100115 A TEMPLATE, DRILL (3) 3/8" HOLES THROUGH DECK FOR HARDWARE. 6 1/2 in 6 1/2 in T-NUT 5/16 H100074 2 5/8 in 6 1/4 in 1 in BOLT WH 5/16x1/2...
Page 123
SS - "C" REVISION TAG - A100316 FINAL ASSEMBLY STEP 4 SCREW PWH 8x5/8 H100128 "C" REVISION TAG (1 PLC) SCREW PWH 8x5/8 (2 PLCS)
Page 124
FA - QUICK LINK - A100069 DP - SWING SEAT GREEN - A100027 HW - CHAIN GREEN 44" - A100048 (1) GLIDER EF - CHAIN GREEN 57" - A100047 FINAL ASSEMBLY STEP 5 TIGHTEN QUICK LINK INSERT CHAIN INTO QUICK LINK CHAIN GREEN 44"...
Page 125
- GROUND STAKE REBAR - A4M00527 KC - METAL GROUND STAKE BROWN - A100178 FINAL ASSEMBLY STEP 6 LAG SCREW BOLT WH DETAIL "A" & "B" WH 1/4x1-1/2 WASHER WASHER 5/16x1/2 H100145 LOCK EXT TWIST STAKES INTO GROUND AGAINST GROUND BOARDS AND CORNER FLAT 9x18 H100115 H100106...
Page 126
WARRANTY AUSTRALIAN CONSUMER LAW Many of our products come with a guarantee or warranty from the manufacturer. In addition, they come with guarantees that cannot be excluded under the Australian Consumer law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Need help?
Do you have a question about the SKYFORT II SWING SET and is the answer not in the manual?
Questions and answers