Motion Access CONDOR SWING MA50777 Installation & Operation Manual

Swing control

Hide thumbs

Table Of Contents

MOTION

ACCESS, LLC

automatic entrance solutions

Installation & Operation Manual

CONDOR SWING

MA50777 Swing Control

For Motion Access Condor Swing Operators

MotionAccess, LLC

toll free: 866-357-8832

775 Nicholas Blvd.

fax: 847-357-8834

Elk Grove Village, IL 60007

www.MotionAccess.com

847-357-8832

info@MotionAccess.com

For technical assistance call 866-357-8832

MA50777-MNL_revN

Table of Contents

Need help?

Do you have a question about the CONDOR SWING MA50777 and is the answer not in the manual?

Questions and answers

Summary of Contents for Motion Access CONDOR SWING MA50777

Page 1 MOTION ACCESS, LLC automatic entrance solutions Installation & Operation Manual CONDOR SWING MA50777 Swing Control For Motion Access Condor Swing Operators MotionAccess, LLC toll free: 866-357-8832 775 Nicholas Blvd. fax: 847-357-8834 Elk Grove Village, IL 60007 www.MotionAccess.com 847-357-8832 info@MotionAccess.com For technical assistance call 866-357-8832...
Page 2 MOTION ACCESS, LLC automatic entrance solutions IMPORTANT INSTALLATION INSTRUCTIONS WARNING – To reduce the risk of severe injury or death: 1) READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. 2) Install only on a properly operating and balanced door. A door that is operating improperly could cause severe injury.
Page 3 MOTION ACCESS, LLC automatic entrance solutions Section A: Installation Instructions DANGER: This controller must be adjusted to ANSI/BHMA A156.10 and A156.19 standards by a qualified person. Unsafe operation may result if standards are not met. Never attempt uses which are not covered in this manual. DANGER: Serious injury or death may result.
Page 4 MOTION ACCESS, LLC automatic entrance solutions Connect the motor harness to the controller’s M1 connector. If using two operators, connect the slave unit using the slave “extension” harness to the M2 connector. Select appropriate program for the application. See the attached “Program Selector” table in the “Controller Settings &...
Page 5 MOTION ACCESS, LLC automatic entrance solutions Install control box into header ensuring wires are not pinched, rotate retaining wings into the header groove and tighten screws. retaining wing DANGER: Never modify harnesses. Unsafe operation may result. For technical assistance call MotionAccess 847-357-8832. DANGER: Stay clear of doors and keep fingers and hands way from moving parts.
Page 6 MOTION ACCESS, LLC automatic entrance solutions Section B: Adjustment Instructions This controller must be adjusted to ANSI/BHMA A156.10 and DANGER: A156.19 standards by a qualified person. Unsafe operation may result if standards are not met. DANGER: Never attempt uses which are not covered in this manual. Serious injury or death may result.
Page 7 MOTION ACCESS, LLC automatic entrance solutions Table: Wiring Inputs at Terminal Block Terminal Function Description ( All sensors inputs are dry contacts.) 12 Vac Accessory Power: Output terminals for accessory power. 10, 11 Power Do not exceed 0.5 Amp. Supply 12,14,16,18 Commons Commons: Commons for all the dry contact inputs.
Page 8 MOTION ACCESS, LLC automatic entrance solutions Section: Controller Settings & Adjustments Program Selector Switch: Table: Program Selector - Low Energy Program Description Two second hold open time when activated by Push & Go. Adjustable hold open time when activated by a dry-contact. Adjustable hold open time when activated by Push &...
Page 9 MOTION ACCESS, LLC automatic entrance solutions Section: Controller Settings & Adjustments (continued) **Ensure power is disconnected from the control before proceeding** To enable the High Energy Programs, the control box must be opened and jumper J2 must be moved to the High Energy position. Safety sensors that are configured to meet the latest ANSI/BHMA A156.10 and A156.19 standards are required for High Energy operation.
Page 10 MOTION ACCESS, LLC automatic entrance solutions Section: Controller Settings & Adjustments (continued) All inputs are dry-contacts. When using High Energy Programs appropriate safety DANGER: equipment must be in place See ANSI standards. Program Selector Switch: Table: Program Selector - High Energy Program Description High Energy applications with safety equipment that meets the latest...
Page 11 MOTION ACCESS, LLC automatic entrance solutions Section: Controller Settings & Adjustments (continued) Table: DIP Switch Settings DIP# Option Description SWITCHES “ON” While closed, the door remains powered toward the Power 2 Sec. closed position until an activation signal is received. Boost When the “Continuous”...
Page 12 Sensor NOT USED Header mounted safety common Data - 2-3 Position black Data - Data + Bodyguard only Switch Motion Access Data + common 3 Position Switches common 2-3 Position green Rocker MA40011 or 12 Vac Switch Activate Key Switch MA40111...