1. Manuals
  2. Brands
  3. Caldwell Manuals
  4. Accessories
  5. 795234
  6. Usage and assembly instructions

Caldwell 795234 Usage And Assembly Instructions

Deadshot chairpod
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

Usage and Assembly Instructions
Instructions #1037447
Product #795234
Revision C
Rear Fork (Buttstock)
Rails
Rail Brackets
Arm Rotation
Friction Knobs
Hook-and-loop Straps
Backpack Strap
Rear Fork Lock Knob
Rail Lock Knob
Tilt Friction Knob
Chair Leg Assembly
Front Fork (Forend)
Rail Extension Locks
Front Fork Lock Knob
Swing-Arm Post
Clamp Lock Knob
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 795234 and is the answer not in the manual?

Questions and answers

Related Manuals for Caldwell 795234

Summary of Contents for Caldwell 795234

  • Page 1 Usage and Assembly Instructions Instructions #1037447 Front Fork (Forend) Product #795234 Revision C Rear Fork (Buttstock) Rear Fork Lock Knob Rail Lock Knob Rails Tilt Friction Knob Rail Extension Locks Rail Brackets Front Fork Lock Knob Arm Rotation Friction Knobs...

  • Page 2: Important Safety Information

    THE DEADSHOT CHAIRPOD SHOULD ONLY BE USED WHEN ALL FOUR FEET ARE FIRMLY IN CONTACT WITH THE GROUND. IT IS NOT INTENDED TO BE USED IN A TREESTAND OR ELEVATED PLATFORM Thank you for purchasing a Caldwell DeadShot ChairPod. Your DeadShot ChairPod is almost completely ®...
  • Page 3 ASSEMBLY AND SETUP INSTRUCTIONS 1. Pull the Seat Leg Assembly out of the Seat Chair Assembly and set it aside for the moment. Photo 1 2. Pass two of the M6 Screws through the Backpack Strap Hook as shown. Photo 2 Photo 1 Photo 2 Photo 3a...
  • Page 4 4. Using a screwdriver, remove the 4 screws in the Chair Seat Assembly shown. Then using the same screws and washers, attach the two Rubber Bar Holders as shown. Photo 4a and b Photo 4a Photo 4b NOTE: These screws only need to be lightly tightened. Over-tightening the screws could damage the Bar Holder.

  • Page 5: Front Fork

    Front Fork Rail Clamp Rear Fork Photo 7 Photo 8 7. Slide the Front and Rear Forks into the Rail Assembly as shown, taking careful note of the orientation of each part. Photo 7 8. Unscrew the top Knob on the Swing-Arm Assembly and remove the top half of the Rail Clamp.

  • Page 6: Usage Instructions

    USAGE INSTRUCTIONS Please refer to the photo on Page 1 to identify the parts and knobs of the ChairPod 1. Unfold the Legs of the Chair by pushing rmly on the frame and pulling on the cross-bar between the legs 2.
  • Page 7 DISASSEMBLY FOR TRANSPORTATION 1. Loosen the Clamp Lock Knob and Remove the Entire Shooting Rest Assembly from the Chair. 2. Fold the forks down and slide the rails to their shortest position, then re-tighten. 3. Loosen the Top Clamp Knob so that the rails can slide easily. 4.

  • Page 8: Maintenance

    MAINTENANCE 1. Periodically check mounting bolts, knobs and fasteners for adequate tightness and function. 2. Application of a rust preventative and/or grease may be needed on exposed threads around Knobs if extended periods of outdoor exposure are anticipated. 3. If play can be felt in any of joints, the bearing set may need adjustment. Remove rubber plug from bearing cap and tighten bearing screw with 5 mm hex key.

Table of Contents