Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MotorScrubber Jet Series
Summary of Contents for MotorScrubber Jet Series
- Page 1 MotorScrubber Jet Instruction Manual...
- Page 3 • Always flush out chemical with clean water after every use. • Never pull the MotorScrubber by its cord or yank it to disconnect it from the battery. • Keep the cord away from heat, oil and sharp edges. •...
- Page 4 THE HARNESS CARRY HANDLE BATTERY PACK WATER PIPE CONNECTION JET PUMP CARTRIDGE HOLSTER 10. FILTER 1L BOTTLE CABLE TIDY CHARGER BOTTLE POUCH ELECTRICAL CONNECTOR The harness should be put over your shoulders like a backpack. There are two adjustable straps which can be pulled to tighten the shoulder supports to a comfortable user level. Ensure the Velcro belt strap is fastened across your abdomen.
- Page 5 THE JET PUMP SWITCH BRUSH SWITCH WATER PIPE & CONNECTOR ELECTRICAL CABLE & CONNECTOR CONTROL HANDLE FLIP CLIP HANDLE SCREWS CHECK VALVE LOCKING KNOB 10. HUB JET ARM 12. JET 13. ROTATING DISC...
-
Page 6: Electric Connection
IMPORTANT INFORMATION Before use, the battery coiled cord needs connecting to the battery terminals. It is vitally important to connect the cable with the correct polarity. If the cable is connected incorrectly it could cause damage / fire when plugged into the charger. Unzip the battery compartment located on the back pack. -
Page 7: Water Connection
WATER CONNECTION Firstly make sure the connector is facing the the pipe stops, roughly 7mm. right way. The white collar of the connector To separate the connection, with two should point towards the harness. fingers, push the white collar towards the Push the water pipe into the connector until black housing and pull the pipe out. -
Page 8: Prime The Pump
PRIME THE PUMP Every MotorScrubber Jet is thoroughly tested in our factory before dispatch. It is possible during storage and transport an airlock will have developed in the pumping system. To release any airlocks present you must complete the priming steps below before the Jet can be used. - Page 9 PREPARING THE CHEMICAL Fill the bottle with clean water, no the cartridge is now pierced and the more than 35°C (95°F), to the neck of chemical released. the bottle. Gently shake the bottle to fully Slide the chemical cartridge into disperse the chemical into the water.
- Page 10 CLEANING WITH MOTORSCRUBBER • When using MotorScrubber make sure the brush or pad is flat to the floor, this will ensure smooth operation of the machine and an optimal clean. • The Jet is a low water use cleaning machine, only a small amount of detergent is required to wet and clean the floor, allow the brush and powerful scrubbing action to release the dirt.
- Page 11 ADJUSTING THE FLIP CLIP The flip clip allows for super fast adjustment of the telescopic pole 1. Release the black clip by pushing up the release catch. 2. Adjust the pole to your desired length then push the black clip back into position. Do not extend further than the red stop line printed on the handle.
- Page 12 CHANGING THE CONTROL HANDLE POSITION Turn the MotorScrubber over so the back of the handle is facing you. Using a 4.5mm Allen key remove the two screws and take off the handle base. Move the handle to your desired position, replace the handle base and screws.
-
Page 13: Battery & Charging Information
BATTERY & CHARGING INFORMATION • The battery should be charged before using your MotorScrubber, after each use, and if unused for 4 months. • When charging the machine the red light will show, when the battery is fully charged the light will show green. -
Page 14: Important Safety Instructions
• Do not allow the cord to hang over the edge of a table or counter, or touch hot surfaces. • Do not use charger for any other uses other than MotorScrubber batteries; other batteries may explode. • Do not operate charger with damaged cord or plug. Replace the charger immediately. -
Page 15: Troubleshooting
TROUBLESHOOTING IS YOUR MACHINE NOT TURNING ON? • If your MotorScrubber is not turning on or is turning slowly check the battery terminals are connected properly and motor to handle plugs are connected securely. • Next, using a voltmeter, simply open the battery pack, disconnect the two leads at the battery, and touch the voltmeter probes to the terminals accordingly. - Page 19 ENJOY YOUR CLEANING...
-
Page 20: Your Warranty
We want you to be 100% satisfied with your Motorscrubber, in the rare event a fault should occur we are here to help and ensure your machine is back up and running as soon as possible. So that we can cover your warranty fully please follow the below terms.
Need help?
Do you have a question about the Jet Series and is the answer not in the manual?
Questions and answers