Advertisement
Quick Links
Advertisement
Related Manuals for ZMODO Greet Pro
Summary of Contents for ZMODO Greet Pro
- Page 1 Greet Pro with Beam Quick Start Guide...
- Page 2 The Beam can extend the range of 2.4GHz networks, and can be used to connect your Greet Pro to a 2.4GHz WiFi network. It can also work as a doorbell chime when paired with a Zmodo Smart Doorbell.
- Page 3 Warning! Do not directly connect the doorbell to the primary power source (110/120VAC and 220/230/240VAC). The Greet Pro was designed to seamlessly replace a pre- existing doorbell button with a mechanical doorbell chime. If you do not have a mechanical doorbell, you must attach a 20 ohm/10 watt resistor (not included) between the connected doorbell and one wire from the power source.
- Page 4 Remove the mounting bracket from Greet Pro. Take your Greet Pro out of the packaging and slide down to remove the mounting bracket as shown below: Slide down Mark and drill the appropriate holes in the wall for the mounting bracket. Snap the provided level onto the mounting bracket and align the bracket against the wall where you would like to install your doorbell.
- Page 5 Then mount the Greet Pro onto the mounting bracket by pushing firmly and sliding downwards. Note: If you are having difficulty sliding Greet Pro onto its mounting bracket, please loosen the security screws.
- Page 6 Installing your Power Accessory: Note: The power accessory is an optional add-on to regulate the power that flows to your Greet Pro. If you hear a buzzing sound from your chime, installing the power accessory will solve the issue. Before installing the power accessory, please make sure that the power to your doorbell is turned off from your circuit breaker.
- Page 7 Transformer Chime Power Accessory Connection Diagram after installing Greet Pro and Power Accessory Remove the cover of your mechanical chime. First, locate your mechanical chime inside of your home. The mechanical chime is the device that rings when your doorbell is rung, and may commonly be a white box mounted on the wall.
-
Page 8: Before You Begin
The following instructions will help you configure your Beam for initial use. The Beam can extend the range of 2.4GHz WiFi networks, and can be used to connect your Greet Pro to a 2.4GHz WiFi network. For detailed instructions and troubleshooting, please visit: www.zmodo.com/support Before you begin: Place your Beam within range of your wireless router. - Page 9 " " ® or the App Store (Compatibility: iOS 9.0+ or Android 4.0+). Launch the app and sign up for a free Zmodo account. All of your devices will be bound to this account. Zmodo Log in and press in the upper...
- Page 10 Select the “Tap here to add a Beam” option at the bottom of the page to connect your Beam. Your Beam will be added to your Zmodo account. Follow the on-screen instructions and select “Tap here to begin setup” to go “AP_ZMD”...
- Page 11 Return to the Zmodo app page and select or enter the SSID and password of the WiFi network that you want your Beam to connect to. Note: The WiFi name and password are case- sensitive. √ to proceed. If you see this screen, the app will connect your Beam to your WiFi network.
- Page 12 Tap to proceed. Note: The password provides an additional layer of security for your devices. You will not need to use this password when accessing your devices from the Zmodo app. It is not required, but it is highly recommended.
- Page 13 Keep away from sources of heat and fire, i.e. a space heater or candle. Place in a cool and well-ventilated indoor area. Do not expose to direct sunlight. If water or liquid damage occurs, power off the Beam immediately and contact Zmodo support.
- Page 14 Configuring your Greet Pro (2.4GHz Network) You can connect your Greet Pro to either a 2.4GHz or 5GHz WiFi network. If you would like to connect to a 5GHz WiFi network, please skip to Section 5. The following instructions will help guide you to connect your Greet Pro to a 2.4GHz WiFi network using your Beam.
- Page 15 Log in and press in the upper right corner. Select "Add Device". Select the “Automatic” connection method to connect your Greet Pro. Your Greet Pro will be added to your Zmodo account.
- Page 16 Greet Pro. Tap proceed. Note: The password provides an additional layer of security for your devices. You will not need to use the passwords when accessing your devices from the Zmodo app. It is not required, but it is highly recommended.
- Page 17 Your Greet Pro has been successfully configured! Configuring your Greet Pro (5GHz Network) Greet Pro supports both 2.4GHz and 5GHz networks. If you are connecting to a 5GHz network, follow the instructions below. For detailed instructions and troubleshooting, please visit: www.zmodo.com/support...
- Page 18 The Greet Pro uses an internal battery for backup power. Once you have mounted your doorbell, let it charge for 30 minutes before attempting mobile setup. Download and install the "Zmodo" app from Google Play ® or the App Store (Compatibility: iOS 9.0+ or Android 4.0+).
- Page 19 Select the “Zink” connection method to connect your Greet Pro. Your Greet Pro will be added to your Zmodo account. √ to proceed.
- Page 20 Note: If you see a "No Internet Connection" error message, please ignore it and connect anyway. Return to the Zmodo app page and select or enter the SSID and password of the WiFi network that you want your Greet Pro to connect to.
- Page 21 If you see this screen, the app will connect your Greet Pro to your WiFi network. This may take a few minutes. Once it’s completed, please skip to step 11. If you do not see this screen, please proceed to step 8.
- Page 22 Note: The password provides an additional layer of security for your devices. You will not need to use this password when accessing your devices from the Zmodo app. It is not required, but it is highly recommended. Your Greet Pro has been successfully configured! You can now share or view your Greet Pro.
- Page 23 Enjoy more smart features in the future. Viewing Options All of your Zmodo devices will be bound to your Zmodo user account. You can access your camera and other devices by using the Zmodo app with any Android or ®...
-
Page 24: Having Difficulty
Your device has successfully connected to the WiFi network. Support Having difficulty? You can use the Live Chat function in Zmodo app if you have any technical problems. Please follow the steps below: Access the “Me” page in the bottom right corner of the Zmodo app and select “Zmodo Support”.
Need help?
Do you have a question about the Greet Pro and is the answer not in the manual?
Questions and answers