REVER MCX1 Instructions page 5

INSTALLATION: REVER MCX1 CONTINUED
DISC BRAKE PAD AND ROTOR BED-IN PROCEDURE
New brake pads and rotors should be put through a wear-in process called
"bed-in". The bed-in procedure, which should be performed prior to your
first ride, ensures the most consistent and powerful braking feel along with
the quietest braking in most riding conditions. The bed-in process heats
up the brake pads and rotors which deposits an even layer of brake pad
material (transfer layer) to the braking surface of the rotor. It is this transfer
layer that optimizes braking performance.
The bed-in process requires you to perform heavy braking. You must be
familiar with the power and operation of disc brakes. Braking heavily when
not familiar with the power and operation of disc brakes could cause you
to lose control of your bicycle, which could lead to a crash and could result
in serious injury. If you are unfamiliar with the power and operation of disc
brakes, you should have the bed-in process performed by a qualified
bicycle mechanic.
Step 1: Accelerate the bike to a moderate speed, then firmly apply the
brakes until you are at walking speed. Repeat twenty times.
Step 2: Accelerate the bike to a faster speed. Then very firmly apply the
brakes until you are at walking speed. Repeat ten times.
ONGOING MAINTENANCE
If you lack proper tools, knowledge, or patience to get the job done right,
visit your friendly, professional mechanic for assistance. In the event you lose
or break part of your Rever brake caliper, spare parts are available through
your local bike shop, or contact Rever directly at info@ride-rever.com.
DISC BRAKE PAD MAINTENANCE
• Do not get oil or grease on the rotor or disc brake pads. This could cause
the brakes to perform poorly or not at all
• If while riding, your brake(s) makes noise, it could be caused by pads that
are worn past the safe, usable limit. Before checking the pads' thickness,
make sure the system has cooled down to prevent injury. Check that
the thickness of each pad is 0.5mm or more, not including the thickness
of the backing plate
• The Rever MCX1 caliper is compatible with the Shimano
disc brake pad shape
GENERAL MAINTENANCE
• Always make sure the front and rear brake are working correctly before
you ride. Squeeze brake levers and attempt to move bike to ensure
cables and brake pads move freely. Check to make sure cables are not
frayed and check housing for cracks and corrosion
• The required braking distance will be longer during wet weather.
Reduce your speed and apply brakes early and gently
• For best performance, make sure the caliper, rotor, and disc brake pads
are free of dirt, mud, ice, or any other contaminants
LIMITED WARRANTY
This Rever product is warranted against defects in materials and workmanship
for two years from the date of retail purchase of the product, subject to the
limitations detailed below. Save your dated receipt for proof of purchase.
This warranty does NOT cover the following:
• Damage due to improper assembly or follow-up maintenance or lack
of skill, competence or experience of the user or assembler
• Products that have been modified, neglected, used in competition
or for commercial purposes, misused or abused, involved in accidents
or anything other than normal use
• Installation of components, parts or accessories not originally intended
for or compatible with the Rever product
• Damage or deterioration to the paint, surface finish, aesthetics
or appearance of the product
• Normal wear and tear
• Labor required to remove and/or refit and re-adjust the product within
the bicycle assembly
This limited warranty is expressly limited to the repair or replacement
of a defective product, at the option of Rever, and is the sole remedy of the
warranty. This limited warranty applies only to the original purchaser of the
Rever product and is not transferable. This warranty applies only to products
purchased through an authorized dealer or distributor. In no event shall Rever
be liable for any loss, inconvenience or damage, whether direct, incidental,
consequential, or otherwise resulting from breach of any express
G-Type
®
or implied warranty or condition, of merchantability, fitness for a particular
purpose, or otherwise with respect to our products except as set forth herein.
This limited warranty gives the consumer specific legal rights, and those
rights and other rights may vary from place to place. This limited warranty
does not affect your statutory rights.
TO THE EXTENT NOT PROHIBITED BY LAW, THESE WARRANTIES
ARE EXCLUSIVE AND THERE ARE NO OTHER EXPRESS OR IMPLIED
WARRANTIES OR CONDITIONS INCLUDING WARRANTIES OR CONDITIONS
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Rever
6400 West 105th Street
Bloomington, MN 55438
1.844.666.8468
Email: tech@ride-rever.com
ride-rever.com
10644 03/15