Pro Auto-Disk; Auto-Drum; Using The Down-Stroke Verification Device? - Lee Precision PRO 1000 Complete Instructions

6
position
2
A
FIG 6
FIG 7

PRO AUTO-DISK

7
Loosen the black knurled adapter on the powder measure and
orientate the measure so the pull back lever aligns with the shell
plate carrier hole, then tighten the knurled adapter.
tach end bell 5 beads from the end of the chain. Place the buffer
spring on top of the end bell. Feed the chain through the hole on
the shell plate carrier. With the shell plate carrier in the down
position, thread the chain through the outer-most hole in the Pro
Auto-Disk actuator lever. Raise the shell plate carrier slightly
and pass one additional bead through the hole. Lower shell
plate carrier, the chain should be taut. Pass the remaining chain
through the inner most hole of the Pro Auto-Disk actuator lever.
The case will actuate the powder measure and the bead chain
will return the powder measure for the next charge. Consult your
powder measure instructions and reloading die instructions
for setting the charge.
PRO AUTO-DISK
FIG 10
Outer-
most
hole
Buffer
spring
End
bell
Handgun Powder Through Expanding
FIG 5
die
(position # 2)
Spin the lock-ring up to the top
[FIG 5]
of the powder through expanding die.
Install powder measure into die. Lower
the press lever (shell plate carrier
raised).
Install powder measure assembly into
turret position # 2. Thread assembly
in until it touches the shell plate, then
back out one full turn.
Powder Through
case into the shell plate and align the
Expanding Die
shell with turret position # 2. Raise the
case into the power through expanding
die to flare the case mouth. Lower the
shell plate carrier enough so that you
can check the amount of flare.
Use your bullet as a gauge. Flare enough
so that the bullet easily starts into the
case. Flare is increased by turning the
die clockwise (closer to the shell plate).
Continue short cycling the press lever
until you've achieved the desired flare,
finger tighten the die lock-ring.
Consult your powder measure instructions and reloading die instructions for setting the charge on
your Auto-Drum instructions pg. 2
At-
[FIG 10]
Knurled
adapter
OR
Insert a
[FIG 6]
Charging
Dispense position
Note: slider drop
tube should not
[FIG 7]
make contact with
top of slot

AUTO-DRUM

OR
Orientate the powder measure so the disconnector aligns with the shell plate carrier
hole and tighten the knurled adapter. Attach end bell to end of bead chain and thread chain
up through the shell plate carrier hole. Raise carrier to the mid stroke position, snap bead
chain into the disconnector slot, lower the ram while lifting the loose end of the bead chain.
The beads will snap through the disconnector and rest in the proper position.
If you select a light target load or fast burning powder that occupies less
than 2/3 of the case capacity, install down-stroke verification device.
Instructions on page 3 of Auto-Drum instructions.

Using the down-stroke verification device?

Attach end bell to end of bead chain
and thread chain up through the
shell plate carrier hole. Raise carrier
to the mid stroke position, snap
bead chain into the disconnector
slot, lower the ram while lifting
the loose end of the bead chain.
The beads will snap through the
disconnector and rest in the proper
position.
Rifle Short Charging Die (position # 2)
This die only ships inside the 223 Remington Pro 1000
Spin the lock-ring up to the top of the rifle short
charging die. Thread charging die on to Auto-
[FIG 8]
Drum knurled adapter completely. Install assembly
two full turns into the turret in position # 2. Insert a
case into position # 2. Lower press lever (shell plate
carrier up). Screw the powder measure assembly into
the press until the case actuates the powder measure
slider drop tube rises and activates the powder
[FIG 9]
measure.
Rifle
Die
FIG 9
AUTO-DRUM
Disconnector
Shell plate carrier hole
FIG 8
Knurled
adapter
3