Table of Contents
Advertisement
ATTACHMENT
OPERATOR'S
MANUAL
42" Single-Stage Snowthrower &
46" Single-Stage Snowthrower
42" Snowthrower Attachment
Mfg. No.
Description
1694144
42" Single-Stage Snowthrower
1694295
42" Single-Stage Snowthrower
46" Snowthrower Attachment
Mfg. No.
Description
1694150
46" Single-Stage Snowthrower
1694296
46" Single-Stage Snowthrower
1724186-06
1723220-06
Rev 11/2004
TP 100-2545-06-AT-SMA
Advertisement
Table of Contents
Related Manuals for Simplicity 1694144
Summary of Contents for Simplicity 1694144
- Page 1 ATTACHMENT OPERATOR’S MANUAL 42” Single-Stage Snowthrower & 46” Single-Stage Snowthrower 42” Snowthrower Attachment Mfg. No. Description 1694144 42” Single-Stage Snowthrower 1694295 42” Single-Stage Snowthrower 46” Snowthrower Attachment Mfg. No. Description 1694150 46” Single-Stage Snowthrower 1694296 46” Single-Stage Snowthrower 1724186-06 1723220-06...
-
Page 2: Table Of Contents
Safety Rules & Information Training ...2 Preparation ...2 Operation...2 Children ...3 Clearing a Clogged Discharge Chute ...3 Service, Maintenance and Storage ...3 Emissions ...3 Decals...4 Required Accessories...5 Reccomended Accessories...5 Clean-Out Warning and Proceedure ...5 Features & Controls Control Functions ...6 General Operating Instructions Checks Before Starting...7 Engine &... -
Page 3: Safety Rules & Information
Safety Rules & Information This machine is capable to amputating hands and feet. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. -
Page 4: Children
20. Do not operate the unit while under the influence of alcohol or drugs. 21. Keep in mind the operator is responsible for acci- dents occurring to other people or property. 22. Data indicates that operators, age 60 years and above, are involved in a large percentage of power equipment-related injuries. -
Page 5: Decals
Safety Decals SAFETY DECALS This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing. Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effec- tively, we have placed several safety labels on the unit to... -
Page 6: Required Accessories
Required Accessories It is required that tire chains and two rear wheel weights or Quick Tach Weights are used. Never operate on slopes greater than 17.6% (10°). Recommended Accessories A rear-mounted weight box can also be added for additional traction. The maximum weight added to the tractor should not exceed 35 lbs. -
Page 7: Features And Controls
Features & Controls CONTROL FUNCTIONS The information below briefly describes the function of individual controls. Operating the tractor and attachment requires the combined use of these controls and additional controls whose operation is described in the tractor Operator’s Manual. Please take a moment and familiarize yourself with the name, loca- tion, and function of... -
Page 8: Checks Before Starting
WARNING If auger does not start and stop when engaging/disengaging electric clutch, see your authorized dealer. Under no circumstances should you attempt to defeat the safety system. Checks Before Starting IMPORTANT NOTE: Refer to Tractor Operator’s Manual for important information concerning safely storing your tractor. -
Page 9: Snow Removal Suggestions
General Operating Instructions Snow Removal Suggestions • Determine the best snow removal pattern before beginning. • Wind direction is an important factor to consider. Rotate the spout to discharge snow downwind. • Plan the pattern so that you avoid throwing snow on cleared areas and on yourself as you are operating. -
Page 10: Maintenance
WARNING To avoid serious injury, perform maintenance on the unit only when the engine is stopped, parking brake is set and all moving parts have stopped. Always remove the ignition key before beginning maintenance or adjustments to prevent accidental starting of the engine. Schedule For Normal Care Care Required Schedule... -
Page 11: Inspect, Adjust, & Lube Drive Chain
Maintenance Inspect, Adjust, & Lubricate Drive Chain See Figure 3. 1. Remove the two flange nuts (A) and chain guard (B). 2. Check the chain. Replace chain if worn or damaged. 3. There should be no slack in the chain, and the sprockets (D and E) should be aligned. -
Page 12: Troubleshooting, Adjustments & Service
TROUBLESHOOTING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and remedies. -
Page 13: Drive Chain Adjustment
Troubleshooting, Adjustments, & Service Drive Chain Adjustment See Inspect, Adjust & Lubricate Drive Chain in the MAIN- TENANCE Section. Skid Shoe Adjustment On smooth surfaces such as concrete or asphalt, the scraper bar should scrape the surface. On surfaces such as gravel, the scraper bar should be set high enough so that it will not pick up debris. -
Page 14: Lift Rod Adjustment
Lift Rod Adjustment In the fully raised position the attachment should be 4”-5” off the ground. In the fully lowered position, the lift rod should compress the spring creating downward pressure on the blade. NOTE: Always adjust the lift height before and after adjusting the downward pressure. -
Page 15: Belt Tension Adjustment
Troubleshooting, Adjustments, & Service Belt Tension Adjustment See Figure 8. 1. With the snowthrower drive belt installed, trunnion (A) should be between marks (G) on spring tension bracket (B) for correct belt tension. 2. Turn belt tension handle (C) to move trunnion for- ward or rearward until it is between marks. -
Page 16: Initial Setup & Assembly
Ref Qty Description SNOWTHROWER GUIDE, Chute, Hold-Down SCREW, Plastite DISCHARGE CHUTE ASSY. MOUNTING BRACKET WASHER, Large LOCKWASHER, 1/4” NUT, 1/4-20 HAIR PIN CLIP CAPSCREW, 1/4-20 x 7/8 SWITCH WIRE HARNESS, Switch WIRE HARNESS, Trailer Plug Figure 10. Initial Setup Ref Qty Description SPRING, Extension BRACKET, Spring... -
Page 17: Install Hitch
Initial Setup & Assembly Figure 11. Assemble Discharge Chute A. Plastite Screw B. Hold-Down C. Chute Ring D. reinforcement Ring Gear INITIAL SETUP & ASSEMBLY NOTE: Some of the following setup procedures may already be completed. Install Hitch Install the sub-frame hitch. Refer to sub-frame hitch installation instructions. -
Page 18: Attach Deflector Control Cable Support
Figure 14. Deflector Control Cable Support Arm A. Support Arm B. 5/16-18 x 1 Capscrew C. Lockwasher & Nut D. 3/8-16 x 1-1/4 Capscrew E. Assist Lever F. Spacer G. Lockwasher & Nut H. Large Washer Attach Deflector Control Cable Support Arm &... -
Page 19: Mount Remote Deflector Control
Initial Setup & Assembly Mount Remote Deflector Control 1. Using the template included in the back of this manu- al, drill two 9/32” holes in the dashboard to mount the remote chute control. See MOUNTING REMOTE DEFLECTOR CONTROL on page 22. 2. -
Page 20: Install Snowthrower
Install Snowthrower CONNECT TO HITCH 1. Position the snowthrower in front of the hitch. Insert the hitch pin (A, Figure 18) through the snowthrower and hitch on both sides of the snowthrower. Secure with a hair pin clip (B). Use the back set of hitch holes (see inset). - Page 21 Initial Setup & Assembly INSTALL ASSIST SPRING 4. Lift the snowthrower up fully and support with wood blocks. 5. Assemble the lift assist spring (B, Figure 21) and spring bracket (C). Install the spring assist bracket (C) in the front bumper. Be sure the spring notch is in the lower position.
-
Page 22: Install Drive Belt
INSTALL DRIVE BELT 8. Route the drive belt as shown in Figure 23. Note that the back of the belt rides in the back-side idlers (B). 9. With the snowthrower drive belt installed, the trun- nion (A, Figure 24) should be between the marks (G) on spring tension bracket (B) for correct belt tension. -
Page 23: Removal
Removal & Normal Installation Figure 25. Dozer Removal A. Rotator Motor Plug C. Hair Pin Clip B. Lift Rod D. Hitch Pin & Clip Removal 1. Fully raise and support the snowthrower with wood blocks. 2. Release the lift assist spring. Remove the spring and spring bracket (E, Figure 25) from the tractor. -
Page 24: Normal Installation
7. Use the trunnion handle (C, Figure 26) to relieve belt tension. Remove the belt from the snowthrower drive pulley (D, Figure 27). 8. Remove the hitch pin and clip (D, Figure 25) from the snowthrower and remove the snowthrower. Reinstall all pins and clips to prevent loss. -
Page 25: Lift Variations When Using Attachments
Tractor Lift Linkage Figure 28. Lift Lock Plate - Hydraulic Lift Models A. Lift Cylinder B. Flat Head Pin (Original) C. Flat Head Pin (New) D. Lock Plate E. Hair Pin Clips F. Lift Shaft Assy. G. Washers LIFT VARIATIONS WHEN USING ATTACHMENTS When a front-mounted attachment such as a snowthrow- er or dozer blade is used with the tractor, the lift mecha-... -
Page 26: Hardware Torque Specifications
Hardware Identification & Torque Specifications Common Hardware Types Hex Head Capscrew Carriage Bolt Standard Hardware Sizing When a washer or nut is identified as 1/2”, this is the Nominal size , meaning the inside diameter is 1/2 inch; if a second number is present it represent the threads per inch When bolt or capscrew is identified as 1/2 - 16 x 2”, this means the Nominal size , or body diameter is 1/2 inch;... -
Page 27: Mounting Remote Deflector Control Instructions
Mounting Remote Deflector Control Line Template Up with Edge of Plastic Dashboard Mark and Drill One 9/32” Hole Mount Bracket and align with Line Mark and Drill One 9/32” Hole Figure 28. Template Location MOUNTING REMOTE DEFLECTOR CONTROL NOTE: Read through instructions before beginning. 1. -
Page 28: Template
Line Template Up with Top Crease of Plastic Dashboard Mark and Drill One 9/32” Hole Line Template Up with Edge of Plastic Dashboard Template... - Page 29 Template...
- Page 30 M A N U F A C T U R I N G , I N C . 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.
Need help?
Do you have a question about the 1694144 and is the answer not in the manual?
Questions and answers