Related Manuals for SGS GPS520
Summary of Contents for SGS GPS520
- Page 1 52CC PETROL TRIMMER OWNER’S MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE.
-
Page 2: For Safe Operation
Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Se- cure hair so it is above shoulder level. WWW.SGS-ENGINEERING.COM PAGE 2 PAGE 3 CALL FOR ASSISTANCE: 01332 576 850... - Page 3 Never use a machine that is faulty. Carry out the checks, maintenance and service instructions de- scribed in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. WWW.SGS-ENGINEERING.COM PAGE 4 PAGE 5 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 4: Components Location Diagram
2. Put the handle assembly into the bracket and put the upper cap over it. Tighten the cap securely. 3. Insert the right handle into the switch assembly and tighten with bolt and nut. WWW.SGS-ENGINEERING.COM PAGE 6 PAGE 7 CALL FOR ASSISTANCE: 01332 576 850... - Page 5 (2), and plate (3) so as to fasten the axle. 2. Mount the trimmer head (8), by turning it anti-clock- wise. 3. Fasten the trimmer head (8), tightly before use. WWW.SGS-ENGINEERING.COM PAGE 8 PAGE 9 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 6: Fuel Safety
Make sure the strimmer unit is off, whilst doing • Avoid all skin contact with fuel. Fuel is a skin irritant. this procedure, to ensure accurate balancing. WWW.SGS-ENGINEERING.COM PAGE 10 PAGE 11 CALL FOR ASSISTANCE: 01332 576 850... -
Page 7: How To Mix Fuel
3. Stop the engine before refilling the unit with fuel. At that time, be sure to sufficiently agitate the mixed fuel in the container. WWW.SGS-ENGINEERING.COM PAGE 12 PAGE 13 CALL FOR ASSISTANCE: 01332 576 850... - Page 8 If you can’t see fuel enter- ing the priming bulb please contact SGS. 5. In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty.
- Page 9 “Run” position (open). Pull the rope up as vertically as you can. Don’t let the rope drag on the casing of the strimmer. WWW.SGS-ENGINEERING.COM PAGE 16 PAGE 17 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 10: Troubleshooting
30- 40 seconds. Your carb adjustment screw. strimmer should now be ready to use. WWW.SGS-ENGINEERING.COM PAGE 18 PAGE 19 CALL FOR ASSISTANCE: 01332 576 850... -
Page 11: Adjusting The Carburetor
Turn the adjustment screw clockwise until the engine speed drops. Now check that the engine still accelerates smoothly when you apply the throttle. WWW.SGS-ENGINEERING.COM PAGE 20 PAGE 21 CALL FOR ASSISTANCE: 01332 576 850... - Page 12 Restart the starting procedure If you're still struggling to start your SGS strimmer after following the troubleshooting please contact us/ If you are still having trouble with your strimmer, then contact us using these methods: Place the sparkplug back into the spark plug wire.
- Page 13 WWW.SGS-ENGINEERING.COM PAGE 24 PAGE 25 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 14: Maintenance
Dry completely be- fore installing. If the element is broken or shrunk, replace with a new one. filter WWW.SGS-ENGINEERING.COM PAGE 26 PAGE 27 CALL FOR ASSISTANCE: 01332 576 850... -
Page 15: Fuel Filter
3. Check to see if any oil or grease has worked its way in be- tween the clutch lining and drum, and if it has, wipe it away using spirits. WWW.SGS-ENGINEERING.COM PAGE 28 PAGE 29 CALL FOR ASSISTANCE: 01332 576 850... - Page 16 Be careful not to spill any fuels during transportation to another spot. When transporting the unit over long distances, ensure the engine is cool to the touch, and that any fluids cannot spill out. WWW.SGS-ENGINEERING.COM PAGE 30 PAGE 31 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 17: For Safe Operation
Ensure that the guard is undamaged sionally. If you need further information please contact us at SGS and is not cracked. Replace the guard Engineering. - Page 18 General rules CAUTION! Muffler is fitted with a catalytic converter designed to reduce exhaust gas 1. Only use cutting attachments with the guards SGS emissions. Engineering recommend! For mufflers, it is very important that you follow the instructions on checking, maintaining, and servicing your machine.
- Page 19 • Only use the recommended cutting attachments as stated by tainers intended for this purpose. SGS Engineering. • When storing the machine for long periods the fuel tank must be emptied. Contact your local authority to find out where to dispose of excess fuel.
-
Page 20: Parts Diagram
Shield Rim 904314 904343 Ring ø15 Guard 904315 904344 Guard Bracket Bearing 6202 904316 904004 Bolt M6x25 Snap ring ø35 902554 904346 Nut M6 Drum 904048 904347 Nut M4 Engine 904178 904348 WWW.SGS-ENGINEERING.COM PAGE 38 CALL FOR ASSISTANCE: 01332 576 850... -
Page 21: Engine Parts Diagram
904246 Square Screw M5 904285 Bolt M5x12 904074 Rope Knob starter 904286 Gasket for muffer 904248 Washer starter 904287 Inner cover 904249 Knob 904288 Inner cover cap 904250 Knob starter 904289 WWW.SGS-ENGINEERING.COM PAGE 40 CALL FOR ASSISTANCE: 01332 576 850... -
Page 22: Ec Declaration Of Conformity
SGS Engineering (UK) Ltd West Side Park Raynesway Derby, DE21 7AZ EC Declaration of Conformity This is an important document and should be retained MANUFACTURER’S NAME: SGS Engineering (UK) Ltd PETROL BRUSH CUTTER TYPE OF EQUIPMENT: GPS520 PART NUMBER: APPLICATION OF EC COUNCIL DIRECTIVES / STANDARD:...
Need help?
Do you have a question about the GPS520 and is the answer not in the manual?
Questions and answers