Thank You For Choosing Kohler Company We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start installation. If you encounter any installation or performance problems, please don’t hesitate to contact us. Our phone numbers and website are listed on the back cover.
Page 3
220 VAC, 15 A, 50 Hz circuit protected by a Class A Ground-Fault Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB). NOTE: This product is designed for installation with the electrical and water supplies located through either the wall or the floor. Kohler Co. 1035530-X2-A...
Page 4
Both types are illustrated. Refer to the dimensional information for your chosen installation. NOTE: A floor mounted water supply stop may be no higher than 2-3/4” (7 cm) from the floor. Install the water supply. If you are installing a floor supply, study the dimensional information illustrated carefully. 1035530-X2-A Kohler Co.
T-Bolts Floor Flange 3. Install the T-Bolts Install two 5/16” diameter T-bolts into the floor flange. 4 Install the O-Ring Place the wax ring in the putty ring located on the tank. Kohler Co. 1035530-X2-A...
Page 6
Position the tank on the T-bolts. Press down on the cylinder where the gasket was mounted. Do not press anywhere else on the tank assembly. Replace the outlet gasket. Position the loose end of the refill tube in the outlet ring. 1035530-X2-A Kohler Co.
Page 7
IMPORTANT! If this installation replaces an existing toilet, a hose other than the one shipped with the water supply may be used. Use a stainless steel, burst-resistant hose. NOTE: This installation is configured to accept a floor water supply. A wall supply is also acceptable. Connect the water. Open the shut-off valve. Kohler Co. 1035530-X2-A...
Page 8
To adjust the water level, use a flat blade screwdriver to gently turn the adjustment rod on the inlet valve. Turning the rod counterclockwise will lower and clockwise will raise the water level. Return the lever to the unlocked (closed) position. 1035530-X2-A Kohler Co.
Page 9
Place the wiring harness plug, level switch wire, and refill tube on the floor so they extend out the rear access opening. Tape them to the floor so they will not be pinched or damaged. Install the collar onto the tank. Clip the spray shield into place over the fill valve. Kohler Co. 1035530-X2-A...
Page 10
Make sure the trapway seats fully in the outlet gasket. If the vitreous shell does not sit evenly on the floor, the trapway is not properly seated. Make all adjustments gently until the trapway is properly seated. 1035530-X2-A Kohler Co.
If any moisture is present, allow the area to dry before plugging the unit in. If hardwire installation is desired, make the electrical connections at this time. Otherwise, plug the pump in. Connect the refill tube. Connect the wiring harness. Connect the level switch. Kohler Co. 1035530-X2-A...
Insert a screw through both grommets. Insert a screw in both of the provided holes and tighten. Do not overtighten. Place a cap over each screw. The caps should be flush with the exterior of the shell. 1035530-X2-A Kohler Co.
Position the tab on the hinge cover with the slot in the hinge assembly and snap the hinge cover into place. With the seat raised, gently push the seat cover forward. The seat and seat cover should close slowly. Kohler Co. 1035530-X2-A...
Place the access cover over the opening in the back of the toilet. Caulk around the base of toilet. Do not caulk the area where the access cover meets the floor. 1035530-X2-A Kohler Co.
(calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. Kohler Company shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite).
Page 16
E. The level switch is not E. Check the level switch properly connected. connection. F. The pump assembly does not F. Replace the pump assembly. work. G. The actuation assembly does not G. Replace the actuation assembly. work. 1035530-X2-A Kohler Co.
Need help?
Do you have a question about the K-3492 and is the answer not in the manual?
Questions and answers